[ Log In ]
[ Register ]

Question #: 109

Question: Where is the sunset?

Current Solution

The sun sets on the western horizon.

Respond:

Other Possible Solutions to this Question

  • where is the company located

    We are located in Katy, TX

    Our Address is:
    20734 Settlers Lake Cir N.
    Katy, TX 77449

    Click the link to respond:
    where is the company located

  • WHERE IS GOOD PLACE TO PUT THE E-STOP SWITCH?

    Locate the switch as close to where you will normally be as possible and in clear sight.

    Click the link to respond:
    WHERE IS GOOD PLACE TO PUT THE E-STOP SWITCH?

  • Where does the sun set?

    The sun sets on the western horizon.

    Click the link to respond:
    Where does the sun set?

  • where is the spreadsheet with all of the parts for the book?

    You can see the component list on the hardware and plans machine (scratch build machine) since it is the same machine in the book:

    https://www.buildyourcnc.com/Item/cnc-machine-scratchbuild

    Additional Information:

    Click the link to respond:
    where is the spreadsheet with all of the parts for the book?

  • where is my order?

    (9/3/2017) Due to Hurricane Harvey and the mass flooding it created in this region, UPS and FedEX has been physically restricted on making deliveries, and during the storm and shortly thereafter, our employees were having the same difficulties. Please call us to determine the status of your order. Please accept our most sincere apologies for this delay.

    Additional Information:
    114-8849667-9189850 my order

    Additional Information:
    I order ArtSoft Mach3 CNC Control Software from amazon

    Click the link to respond:
    where is my order?

  • Where is sunrise?

    The sun rises on the eastern horizon.

    Click the link to respond:
    Where is sunrise?

  • WHERE ARE THE ELECTRONICS WIRING VIDEOS?

    The blackFoot CNC machine kit does not include a table. The table can be made as long or shot as you need. for instance, if you are looking for a travel of 4 fet x 4 feet, then the table will need to be about 6 feet long to get the full 4 feet of travel.

    The electronics are very straight forward using the connection diagram for the breakout board that you select. Use the videos for a general idea and then use the connection diagram to verify the correct connections for the interface of your choosing.

    Yes,the USB interface replaces the breakout board, but remember that you will need to use the planet-cnc software with the USB interface.

    Additional Information:
    The electronics does accompany the cnc machine kits as long as you select the option "with electronics". There are option to purchase the machines without electronics and that would be necessary if you either have your own electronics, or you prefer the plug and play cnc computer system we call the redLeaf, or redSprout. This will also be necessary if you prefer the electronics that use the USB interface rather than the parallel interface.

    Click the link to respond:
    WHERE ARE THE ELECTRONICS WIRING VIDEOS?

  • WHERE ARE THE ELECTRONICS WIRING VIDEOS?

    The electronics and wiring videos are located under the tutorials section (click Tutorials on the top menu. The Title is "CNC Electronics and Wiring". The actual link to these videos is: https://www.buildyourcnc.com/CNCElectronicsandWiring.aspx

    Additional Information:
    You will also find the electronic wiring videos for the USB controller at: https://www.buildyourcnc.com/tutorials/tutorial-Electronics-USB-Interface-Wiring

    Click the link to respond:
    WHERE ARE THE ELECTRONICS WIRING VIDEOS?

  • Where are the previously asked questions?

    The recently answered questions have be reworked to show the last 100 questions. To show a more concise view of the questions and answers, only the question is shown and you can hover of the questions to see the answer.

    Click the link to respond:
    Where are the previously asked questions?

  • Is there anywhere i could see one of your machines,12" x 36",working,thanks

    You can see pictures and info on our machines on the gallery link in the top bar.

    Here are a few links for the blueChick CNC:
    Rot Aylett's:



    &feature=youtu.be

    Click the link to respond:
    Is there anywhere i could see one of your machines,12" x 36",working,thanks

  • Where is the 5v terminal on the parallel breakout board to power the board?

    The parallel breakout board contains a USB port to power the board. Through the USB port, the computer delivers 5v of stable power to the parallel breakout board, but doe not provide any communication as would normally be associated with USB connectivity.

    The reason we elected to use the USB port to provide power is to remove the need for an external 5v wall adapter.

    Click the link to respond:
    Where is the 5v terminal on the parallel breakout board to power the board?

  • where do I download the trial version of Mach 3

    You can download the Mach3 software at this link:
    http://www.machsupport.com/software/mach3/

    Click the link to respond:
    where do I download the trial version of Mach 3

  • Where are the datasheets for the stepper motors?

    You can find the datasheets to our motors be going to the the stepping motor category page https://www.buildyourcnc.com/category/nema and selecting the motor. This will bring you to the product page for the motor and all of the motor information will be found there.

    Click the link to respond:
    Where are the datasheets for the stepper motors?

  • How to use the power supplier with laser an commands ? Where is the documentation ?

    Dealing with our laser power supplies you can find a simple schematic/wiring diagram here ((Parallel)https://www.buildyourcnc.com/images/LaserWiringParallel.jpg / (USB)https://www.buildyourcnc.com/images/LaserWiringUSB.jpg),
    Now you can also find steps for our blackTooth laser cutter/engraver from steps 55-68 on our website here (https://www.buildyourcnc.com/blackToothLaserCutterAndEngraver.aspx).

    One of our previous customers gave us a courtesy of making a detailed forum on our blackTooth laser cutter assembly (http://blacktoothlaser.blogspot.ca/2013/04/index-for-blacktooth-laser.html?view=classic).

    Click the link to respond:
    How to use the power supplier with laser an commands ? Where is the documentation ?

  • Where is the link for the expansion kit for the CNC Routing Machine Kit Version 1.3?

    You can use the board5.nc as the expansion parts.

    Additional Information:
    20

    Click the link to respond:
    Where is the link for the expansion kit for the CNC Routing Machine Kit Version 1.3?

  • I WOULD LIKE TO KNOW IF THERE IS A STORE OR SHOP WHERE CAN SEE THE PRODUCT AND BUY IT?

    If you are located near Houston, Texas area you can stop by our shop. If you are not near us, you can check in our forums, and see if you can find someone in your area that has one of our machines, and would be willing to let you come see it in action.

    Click the link to respond:
    I WOULD LIKE TO KNOW IF THERE IS A STORE OR SHOP WHERE CAN SEE THE PRODUCT AND BUY IT?

  • z axis 1/4" drill rod, wheres it go?

    Which machine are you referring to?

    Additional Information:
    they are the x axis drive extensions

    Click the link to respond:
    z axis 1/4" drill rod, wheres it go?

  • where is my purchased cad/cam software?

    Mach3 or Mach4 licenses purchased from us go through a process that includes us purchasing the license from the Mach3 developer first. The developer can take up to 2 hours to delver that license back to us to be emailed to the customer.

    If the license was purchased outside of business hours, then we will start the process at the beginning of the next business day.

    If you notice a delay in this process, please give us a call so we can provide a status, or let us know that you purchased the license so we can get the process going. Even during business hours, it may take some time to get to your order with our workload.

    Thanks.

    Click the link to respond:
    where is my purchased cad/cam software?

  • Where does the Laser Controll unit mount on a Blacktooth?

    Just my luck. As soon as I posted the question, I found 4 holes that match the controller on the back panel near the fan. Can you confirm?

    Click the link to respond:
    Where does the Laser Controll unit mount on a Blacktooth?

Get Help with:
This Product
Orders
Tech Support
Sales
This Product
Order Query
Tech Support
Sales
Not logged in. Log In Register
Track Order(s)
View Order(s)
I Want to Schecule a One-On-One Paid Tech Support Session
Book an Appointment Pertaining to a BuildYourCNC Product (Free)
Ask a Quesion Below (Free):
Book an Appointment Pertaining Other Equipment ($60/half hour)
Book an Immedite Appointment Pertaining Other Equipment ($120/half hour)
Ask a Quesion Below (Free):
Waiting for response... I may not answer immediately, but I was notified on my cellular phone so my response is forthcoming. If I don't respond immediately, you can always go to the [My Account] page to see all of our chats at any time.