Yes, the 651 oz/in motor requires a driver that is compatible to the motors (the motor will draw 6 amps max and the driver paired with this motor will be able to allow for a 6 amp draw). I would also recommend a 36 volt power supply for better high velocity performance.

Click the link to add information to this solution:
I have one of your smaller stepper motors running my X AXIS bridge crane and if it is moved to fast the stepper motor sounds like it is skipping steps will the 651oz stepper motor require a different power supply and controler?

BYCNC Response:
This is correct. You will need to use a method appropriate for the software you are using. Also remember that NC switches are typically wired in series, while NO switches are normally wired in parallel.

User Response:
I am using the cnc planet software for your USB board. Are the limit configurations in this software?

BYCNC Response:
Yes, Planet CNC software is compatible with the use of limit switches. Configuration information will depend on your specific application. You can view Planet CNC's information here: http://www.planet-cnc.com/files/CNCUSBController.pdf

Click the link to add information to this solution:
LIMIT SWITCHES FOR AXIS. THE PRINT SHOWS THAT YOU CAN WIRE LIMITS EITHER N.O. OR N.C. SO IF THIS IS CORRECT I WOULD NEED TO TELL BOARD IN SOFTWARE HOW LOOK AT THESE LIMITS, I'M GOING GET AN INPUT LOOSE DEPEND ON IT.

Since you mentioned there is a nasty smell, I'm wondering if there might have been a issue with the power supply. Can you email us your name for the order and specific voltage you are using for the redFly? at techsupport@buildyourcnc.com. Also I want to mention if you have the USB cord plugged in to the redFly if it has the parallel interface board?

Click the link to add information to this solution:
When I first hooked up my redFly and was manually testing all the axes, everything was going well, then my Y axis stopped working all together, and now my X and Z have stopped also and my redFly has a nasty smell coming from it and none of the stepper motors seem to be getting power.

We can configure the redLeaf or redSprout to control the motor of a 4th axis. The driver we use for the motor on the 4th axis is our standard 3.0 amp driver.

Click the link to add information to this solution:
If I purchase the Heavy Duty redleaf system (651 oz-in motors) and your 4th Axis Tail Stock setup will you configure the 4th axis to the computer? Your site states the 4th axis add on is "for a total of 4 axes 425 oz-in motors only"

All of our controller will allow two steppers on any of the axes. Multiple stepper motors and drivers on a single axis is more a function of the way the stepper motor drives are connected to the output pins of the controller. To connect two stepper drivers to a single axis, you need to connect the output pins (dir and step) to each of the two stepper motor drivers.

Consider the controller on cost, features and how they are connected to the computer.

Out lowest cost controllers are:

Mach3 USB board - Has good features and uses the USB from the computer as the main connection
https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Parallel Breakout - The computer generates the main signals and this board conditions the signals for the drivers. Although it requires the parallel port from older computer, the board has the most broad compatibility with control software out there including Mach3 and LinuxCNC.
https://buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay

Highest cost but most feature rich:

Pokey57CNC - works with both Mach3 and Mach4
https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Click the link to add information to this solution:
I am looking for a controller for a 3 axis dual Y stepper cnc machine. If at all possible I would like a list of the parts that will be needed. I prefer to go with an ethernet setup vs a parallel port.

The leadscrew length for the greenBull long Z-axis is 47 inches.

Additional Information:

Click the link to add information to this solution:
BUILDING ONE OF YOUR GREENBULL 6X LONG AND 2.2 KILOWATT SPINDLE DOES NOT FIT. SEEMS LEAD SCREW YOU SENT WITH KIT IS SHORT 42" LOOKS LIKE IT NEEDS TO BE 5 OR 6 INCH LONGER. THIS CORRECT? WHAT THE NEEDED LENGTH FOR UNIT?

it is possible to install 2 motors on a single axis but you will require another driver and motor, but wire it directly to the same pins on your breakout board. Also the orientation of your motor since it is opposite side of the original so getting it to move accordingly to the original motor it will need to be orientated correctly. The slight shift could be the cause of the rod not being completely flat where the set screws are suppose to tighten the sprocket to the rod, so sanding it to a flatter surface might fix the shift in directions.
Currently do not have a kit or schematic available.

Click the link to add information to this solution:
I am interested in your Black Toe (24" X 48") machine, and am wondering if using two medium motors on the "X" and "Y" axis makes sense relative to power and alignment (racking). What would you recommend?

This is most likely a wiring issue. I would disconnect all of the power to the drivers and reconnect one at a time to isolate the problem.

Additional Information:
that was not helpful. I already did that way before submitting this question. there are not that many wires here and I have already rewired this a few times. I actually think its a software or interface board issue because it does work sometimes but then trips (possibly a amperage / voltage issue) I am using the interface board that has a parallel port and usb for 5V. are there different settings that I need to setup?

Click the link to add information to this solution:
I'm using the big 651oz in stepper motor for X and Y and the smaller 325 for the z and X and Y keep tripping when I try to tune the motors on Mach3 but Z seems to work. I have to turn power on and off to reset....is this a wiring issue?

The leadscrew length for the greenBull long Z-axis is 47 inches.

Additional Information:

Click the link to add information to this solution:
Building one of your greenBull 6X Long and 2.2 kilowatt spindle does not fit. Seems lead screw you sent with kit is short 42" looks like it needs to be 5 or 6 inch longer. Is this correct? What is the needed length of lead screw for this unit?

If there is play within the motor itself, then that motor may be defective. Call us to provide us more detail on this issue.

Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:
Ins9kru1

Additional Information:
-1 OR 2+486-486-1=0+0+0+1 --

Additional Information:
-1 OR 2+693-693-1=0+0+0+1

Additional Information:
-1' OR 2+890-890-1=0+0+0+1 --

Additional Information:
-1' OR 2+307-307-1=0+0+0+1 or 'HN9afNei'='

Additional Information:
-1" OR 2+88-88-1=0+0+0+1 --

Additional Information:
1'"

Additional Information:
1����%2527%2522

Additional Information:
@@mxOzC

Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
I have NEMA 34 motors for a GreenBull 6x12. After 2 weeks of use, my Y axis motor has developed play in the front but not rear of the motor. Is this a motor defect or has something come loose somewhere? Thanks,

Cutting metal with lasers even at 100W and 130W is difficult. The main problem is molten is a byproduct of lasing, which can severely damage the laser.

Click the link to add information to this solution:
For the XL Vertical Laser Machine I see it won't cut metal as it is only 80w. However, I noticed that you are working on 100w and 130w versions so will that be sufficient to cut through sheet metal? If so, how much longer until those are available?

The upper right hand corner of the data sheet found at https://buildyourcnc.com/Documents/PN.SM86HT80-5504B-U(inhouse%20PN.85BYGH450A-47-80)%20(1).pdf labels the coil wires A-D and also by color, which refers to the colors coming off of the motor. Our specification for A+, A-, B+, B- follows the labeling of the driver connections where A+ is coil A's positive lead and the same for the B coil. If you find yourself wiring 4-wire stepper motors without a datasheet, you can easily determine which colors go together with an ohmmeter. Each pair associated with the same coil will have continuity (negligable resistance) between them.

Additional Information:


Additional Information:
https://buildyourcnc.com/Documents/PN.SM86HT80-5504B-U has an error
HTTP Error 404.0 - Not Found
The resource you are looking for has been removed, had its name changed, or is temporarily unavailable

Click the link to add information to this solution:
Wiring the greenBull stepper motors, in the video you say to look at the data sheet for the motor, which is the 651, in the data sheet it shows A, B, C, D, for the colors, and in the video you say A+, A- and so on. Is there a video for wiring the connection to the RedFly that I bought to better explain what I need to do next. I'm using 16c4 SO cord, so I can match color to color on the motor side.

This sounds like a problem with the step (pulse) signal. The driver motors receive two signals from the computer via the board -- one is high or low and tells the motors which direction to turn, one is a square wave pulsed signal(quick that tells the motor to turn or a constant high signal that tells the motor to maintain its position. With an oscilliscope you can check for proper signal at the board. If you bought the board from us, please contact us to arrange a return authorization.

Click the link to add information to this solution:
Y axis on usb controller not working. The motor gets power and holds but will not turn. I tried switching the same wires, driver, and motor over to the A axis on the controller and it works fine like that. I have double, and triple checked the wiring

You can download a trial version of PlanetCNC software from their site at http://www.planet-cnc.com/index.php?page=software to see how you like the interface. If you look at their main GUI screen, along the left side you will see 4 boxes labeled X,Y,Z and A. These represent the axes the software is equipped to control. (A being Axial, or rotational motion) Typically a separate motor and driver is used to control each axis. If you plan to switch axes you will need to connect and disconnect the outputs from your software to the drivers.

Click the link to add information to this solution:
sorry, this is what i meant to say: OK, so if I use the USB version then I would find the rotary/linear axis definitions in the planet cnc control software somewhere. I will be needing to change axis type often for various projects that is why I am asking.

Recommend first test to check a non-working axis, is to connect the current working axis(ex X-axis) to either the y/z axis to test the actual board and wiring in other axis setup. If tests failed and working (x-axis setup) does not working in the new axis location, go the Planet-CNC/File/Settings/Axes and check if your current non-working axis setup requires a inverted pulse. Check box and test again.
Next test if first fails, is to check continuity in your wires. A simple multimeter(ohm's) will work, just connect the positive and negative ends to one side of the same wire and if reading comes to 0.000, wire has continuity and if reads 0.L then there is a break in the wire and should be replaced.

Click the link to add information to this solution:
I installed the USB CNC Planet and got out of your USB controler $ 75 .Viska have linked to a video 'Party - 2.. X - running and y and z-axis does not work, it moves step motors and controller positions X -axis works, and Y and Z does not work.

When you press the x-axis limit switch, does the LED emit light?

Click the link to add information to this solution:
I currently have my whiteant build complete. But when I go to print the 20mm x 20mm box I seem to be having issues. The Z axis does not seem to move. Also the X axis hits the limit and does not move of of it. What is the best way to trouble shoot this issue?

If your axis shutters and will not move unless moved by another force, that sounds like your acceleration is set too high. Lower the acceleration until it works well, then lower it a bit more to have a margin of safety.

IF that didn't work, try swapping the X and Y drivers. That way you will pinpoint if the issue is the driver. If the proplem persists, then there may be an issue with the motor itself.

The X and Y drivers can be easily swapped by swapping only the motor wires.

- Remove the x-axis motor wires from the X driver.
- Remove the Y motor wires from the Y driver.
- Insert the X motor wires into the Y driver.
- Insert the Y motor wires into the X driver.

Now the Y-axis will move the gantry. Test the Gantry movement by moving the Y axis using the up and down arrow keys (mach3).

Click the link to add information to this solution:
X AXIS STEPPER MOTOR STALLS AND SHUTTERS WHEN COMING FROM A STAND STILL WON'T MOVE WITHOUT PUSH BY HAND. I TOOK THE CHAINS OFF SPUN FINE WITH OUT LOAD. HAVE CHAIN HOOKED UP CAN MACHINE BACK FORTH HAND, NO HANG UPS OR ANYTHING, BUT TRY TO IT DOESN'T JUST SPINS OUT. ANY SUGGESTIONS?

What controller are you using to control the cnc machine (Mach3 usb, parallel breakout board, etc.)?

The spindle VFD has an input for 0-10 volts to control the speed and can be used with the MAch3 USB or the Pokeys57CNC board. There are also other terminals in the VFD to control the forwared/reverse and start and stop. Mach3 has parameters to control these output and you need to specify which pins are used for these.

You can also use the TX/RX RS-485 connection on the VFD to have total control using an FTDI USB to serial connector board to connect the computer directly to the VFD.

How to connect the USB to Serial adapter to the VFD:
https://www.buildyourcnc.com/FAQ/13790

FTDI USB to Serial:
https://www.buildyourcnc.com/item/Interfaces-newbiehack-Interfaces-TTL232R-USB-UART-Serial

Pokeys57CNC board:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Mach3 USB board:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Parallel Breakout board:
https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay



Additional Information:
I do apologize for leaving out the parts list.
Leadshine MX4660 4-Axis Digital Stepper Motor Driver
Ethernet SmoothStepper
YL600-2S-2K20 VFD
4 Relay control board
Has anyone had any success getting Mach3 to control the spindle speed and direction?

Click the link to add information to this solution:
I have the 2.2KW VFD. I would like to have it controlled through software. What are the Mode parameters that need to be changed that will allow FWD/ REV, START/STOP and RPM control?

Did you set them up as limit switches or home switches?

Additional Information:
Not sure where do I check that?

Additional Information:
Go to config, then ports and pins, then input signals.

Additional Information:
The limits are labeled x++, x— for example.

Click the link to add information to this solution:
I'm using Mach3. I have 2 limit switches on X, 2 on Y and 1on Z for retracted/home. I can go to diagnostics and see the switches/inputs working. But when I move with jog or gcode they have no effect. Also I can go right past the soft limits. I must have something turn off but I don't know what.