Yes, you can send your electronics to us for repair, or retrofit to work with either Mach3, Mach4 or LinuxCNC. You can send us an email at customerService@buildyourcnc.com to set up your appointment.

Some of the types of CNC electronics we will consider.

- We will work on electronics from other manufacturers as long as you are ok with the Mach3, Mach4 or LinuxCNC control software for your CNC machine or CNC router.

- We will repair or retrofit used CNC electronics.

- Some customers find that electronics are overwhelming to put together so we will finish these electronics wiring and assembly for you.

The cost for these includes labor cost for the time it takes to finish the CNC electronics repair or retrofit and for any parts that need to be replaced or added.

Here is an example of CNC electronics that we worked on for a customer:

Click the link to add information to this solution:
I would like to use Mach3 instead of the software for my CNC router. Can you fix the electronics for me?

The best way to determine how to control your VFD using Mach4 is to read the MAch4 manual found here:
http://www.machsupport.com/wp-content/uploads/2014/05/Mach4%20Installation%20Manual.pdf

You will find that there a a few ways to control the spindle/VFD on your CNC machine or CNC Router.
- The first and easiest is to have your VFD's power controlled by a relay. This will allow your spindle to have on/off control through Mach4 with an output pin.
- The second is to have a controller output a DAC voltage between 0-10 volts to control speed on the VFD/Spindle. There is a termial on the VFD to receive this signal line. The controller will also have an output that outputs a high or low and that can control the on/off on the VFD.
- The third, and more difficult of the three methods is to use a USB to Serial adapter (USB to USART or RS-485). The Computer plugs into the adapter using a USB cable and the adapter uses the RX/TX to connect to the VFD's terminals for communication. This will provide a great amount of control. Mach4 will need a plug-in to make this option work.

Click the link to add information to this solution:
How can I control my VFD using Mach4 cnc control software?

The post-processor that should be used in Aspire, Vectric V-Carve, Cut 2D, and other CAM programs in their suite should use Mach 2/3 Arcs (inch) or Mach 2/3 Arcs (mm).

Click the link to add information to this solution:
[575] Is there a special .tap g code file I should use with this mach3 controller I’m using aspire as cad

You will need a cam program to create machining operations for the geometry in the .dwg file. The CAM program outputs these machining operations into g-code for the control program (planet-cnc) to use.

I have a couple of tutorials that explain this concept.
http://www.buildyourcnc.com/tutorials/Tutorial-sketchup-fabrication-fabricate-cad-cam-dxf

The following is an older video but get's the point across:
http://www.buildyourcnc.com/process1.aspx

Additional Information:

Click the link to add information to this solution:
HAVE CAD FILES (.DWG AND .DWF) FOR THE GUITARS. HOW DO LOAD THEM INTO PLANT CNC SOFTWARE USE?

If you would like to remove the malware or flash adware called text-enhance, follow the steps on this wab page: http://botcrawl.com/how-to-remove-text-enhance/

Click the link to add information to this solution:
How can I remove the text enhance malware adware hijacker software?

Yes, I will need to know more specifics of the machine so I can recommend the correct electronics.

Click the link to add information to this solution:
ok I Build my CNC machine table and now need a complete set for motor and software how you can help me

If you take the standard parallel cable BoB (Break Out Board), then you will need control software (Mach 3 or EMC2) and CAM software to make your G-Code (such as CamBam). Personally I use CamBam and Mach 3, they work beautifully but don't expect to turn them on and know how they work out of the box. Give yourself a few weeks to get familiar with the basics. CamBam is VERY powerful software for it's price. I'm surprised how much I keep learning on what I can do with it...I highly recommend it if you want as much control as possible.

Mach 3 + CamBam as a bundle costs $310. EMC2 will give you a free replacement for Mach 3 and is exclusively for Linux.

If you use the USB BoB, it will cost an extra $75 + $75 for the software. This is an all-in-one package so no need for Mach 3 or CamBam.

For etching rasters (jpeg, bmp, tiff, non-vectors, photos), I highly recommend PicEngrave. It has been a labor of love for the past 9 years and John has done a wonderful job with it. It easily compares in quality compared to software that is in the $200-$300 range. John's software runs $40 and can be found here: http://picengrave.com/ (don't let the modest website fool you, this stuff can do amazing things). DotG and the Mach3 engrave plugin are two other options and instructions can be found on Dustans page in the gallery on buildyourcnc.com website.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
WHAT SOFTWARE CAN BE USED WITH THE BLACKTOOTH LASER CUTTER?

You can call us, send an email, or pose the specific question on this customer service live that pertains to the issue that you are having.

Click the link to add information to this solution:
Im having software setup problems with my backtooth (mach3) and i seem not to find a solution in the forum. what can i do?

The main components for a CNC machine, includes:
Computer (required with correct OS system for compatibility with the CNC control software and interface board)
CAD/CAM Software
CNC Control Software (Mach 3, Planet-CNC, Linux-EMC2)
Interface Board (Our current models: Parallel interface board(mach3), USB interface board(planet-CNC))
CNC Electronics (which should be included with most cnc kits)
(ex.) Drivers, Motors, Power Supply, Interface Board
CNC Machine

Miscellaneous Items:
Limit Switches
Cable Carrier
Wires (different gauges)
End Mills/Bits
Vacuum
Emergency Stop Button
Spindle/Router

Click the link to add information to this solution:
I have computer, Cad/Cam software and my router unit not sure what else I need?

The plans or DXF files are not offered. We sell the machines as kits or fully assembled. The kits are very well priced and will most likely cost less if materials and labor than working from plans (this comes from feedback from many customers that built similar machines from plans).

Click the link to add information to this solution:
co you sell plans so I can cut my own laser setup??

A cutting surface. I bought myself a aluminum 'egg crate' mesh from my local HVAC company. They are used a cover for fluorescent lights and work great for low impact cutting surface. They come in 4'x8' sheets and are easily cut to fit. The other side is if you can find a steel honeycomb cutting bed to fit. These can be quite costly or fairly affordable depending where you are looking. The benefit of a steel honeycomb is you can use high power magnets to hold material down.

Click the link to add information to this solution:
WHAT CAN USE BELOW MY WORKPIECE AS SUBSTRATE IN BLACKTOOTH LASER CUTTER?

Planet-CNC is the control software. If you decide to use the USB controller, you will need to use the planet-CNC software as the control software. You will be able to use any of the CAM software applications with the planet-CNC control software.

Click the link to add information to this solution:
Would I be able to use the Mach3 CNC Control Software or any of the CNC CAM Software(BOBCAD/CAM,CAMBAM) if I choose to use the Planet-CNC USB Interface Board?

You can find the latest version here http://www.planet-cnc.com/index.php?page=download

Additional Information:

Click the link to add information to this solution:
Where can I download the USBCNC software? The https://buildyourcnc.com/files/CNCUSB_20130308.zip link is dead.

For software, you will need some sort of CAD (Computer Aided Design) software to draw your designs (such as SketchUp, AutoCAD, Corel Draw, etc.).

You will then need CAM (Computer Aided Manufacturing) software to apply machine operations to your designs, and to export "G-code". We suggest CamBam. CamBam also has CAD capabilities, but they are quite limited and inefficient, so I would suggest using separate, dedicated CAD software.

The final piece of software is for controlling the CNC machine. We suggest Mach3. This program reads the G-code and controls the movement of the CNC machine.

CamBam and Mach3 can be found here: http://www.buildyourcnc.com/CNCsoftware.aspx

Click the link to add information to this solution:
What kind of software do I need?

Have you tried comparing all of the parameters for the motor outputs? For instance, go into the motor outputs screen in the mill profile, take note of all the parameters. Then open the turn profile, go into the motor outputs and change the parameters from the notes you had in the mill profile.

If that works, do the same for the other setting screens.

Click the link to add information to this solution:
[575] Everything works in mill, but if I wanna use turn software then there is problems to recognize rnrmotion card.

An unhandled exception generally means that, in the program code, the program is not checking against every possible exception that could occur. Most likely, this exception is caused by some limit that is being exceeded (or the other way around). I would remove any files that could be associated with the program, like setting files, or even register configurations associated with that software. Also, make sure that you completely update your version of windows.

Check to make sure all of the drivers are current for your graphics hardware. Make sure that your graphics hardware works in other programs as well.

If you upgraded the Windows version, check to make sure your graphics hardware is compatible with the new version of Windows. Unhandled exception issue may be associated with graphics hardware and compatibility.

Customer Response:
I've given up on the wiped laptop and loaded the program on a different computer using windows 8. At first it won't operate my CNC until I read on Planet-CNC forum about loading the drivers on windows 8. All working now. Will run through the calibrations again today. Thanks

Click the link to add information to this solution:
I had to wipe my computer due to virus and now can not download the USB software again. I get a "unhandled exception" error message. Any suggestions?

The USB interface that we sell only works with planet-cnc software. We will be developing our own USB board and plug-in that will work with Mach4 very soon.

Additional Information:
does the mach3 usb interface board work with mach4?

Click the link to add information to this solution:
Can I use your USB interface board and Mach4 on my 3 axis CNC router?

Planet-CNC is the control software. If you decide to use the USB controller, you will need to use the planet-CNC software as the control software. You will be able to use any of the CAM software applications with the planet-CNC control software.

Click the link to add information to this solution:
Can I use your USB interface board and Mach3 on my 3 axis CNC router?

You can find instructions for the Mach3 USB here:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

You will probably need to use the Mach3 USB board with Mach3. We have not tested the Mach3 usb card with Mach4.

Click the link to add information to this solution:
Whereb can I find directions on how to install the Mach3 USB board with Mach 4 software? I do not have a parallell port.