[ Log In ]
[ Register ]

Question #: 13249

Question: Running Redleaf 3 axis Bobcad/mach3 Won't cut circles w/o two imperfections at 180 degrees from each other

Current Solution

Make sure the drive sprockets are very tight. There the mechanical parts are loose, circles will be the first geometrical shapes to show this issue.

Additional Information:

Respond:

Other Possible Solutions to this Question

  • What causes one of my two x-axis motors to stop while the Mach 3 program is still running?

    If one of your stepper motors decides to stop moving and the others are moving during a CNC milling or laser cutting job, then there could be two things that could be causing this.

    - The motor found its limiting torque (usually comes with a not-so-pleasant sound). This is where the control software is trying to move the stepper motor too fast (velocity, or too fast too quickly, acceleration) and the load against the stepper motor (inertia of the machine, or the material against the end mill while milling). Recommended action is to lower the velocity and/or acceleration, and/or lower the feedrate when cutting.

    - There is a wiring issue with the wiring from the driver to the motor. This could be a loose wire, or a chafed wire (or two shorting together). It can also be a loose digital wire from the controller board to the driver. Sometimes wire ties can be the culprit. Recommended action would be to thoroughly inspect the wiring.

    It's probably not the limit switches since that would cause a stop to the entire motion of the cnc router or laser machine.

    Sometimes Mach3 will show a status when something goes wrong, but in cases where the motor is stopping due to its torque limit, then that would not be shown in the status. It's always good to check it anyway.

    Additional Information:
    I need to clarify my situation a little better after going to my shop and trying to run another program on Mach 3. About 15 minutes into the milling process all the motors (2-X axis, Y axis and Z axis)stop but the program continues to run. I stop the program and after a couple of minutes when I try to restart the program all the motors start working again. Then after another 15 minutes or so, all the motors stop again. I checked and rechecked my wiring. This has never happened to me before when running the same programs with the same setups and motor speeds. All of a sudden when I reloaded a program I successfully used before it does this. Do you have any recommendations?

    Additional Information:
    Yeah, it sounds like a more complex issue. Have you tried running in the air without using the spindle. This may be a power related issue.

    Additional Information:
    That's exactly what I did. I ran the program without the router motor on just to see if the motors would get through the whole program but they stopped working after about fifteen minutes and then I was able to start them again after about 3 or 4 minutes. I never had this problem before so you can imagine my frustration especially after ruining a couple of projects on expensive material.

    Additional Information:
    Sure. I can completely understand. Try this: disconnect all but one of the driver from power and digital connection and do the air run. Repeat this for each driver and note your findings. This will rule out the drivers causing a power failure.

    Also, is your stepper motors and drivers on a separate power circuit from the computer?

    Additional Information:
    I will try disconnecting each driver and digital connection, which will be a real pain because it will be hard to access.

    All the stepper motors, drivers and computer are plugged into the same power strip.

    Additional Information:
    Ok, so there is no power failure going on, but I believe it is necessary to test each stepper motor and driver pair individually. Hopefully that will lead to a conclusion.

    Additional Information:
    It will take a little time but I will do it and report back on my findings.

    Additional Information:
    Curious, what machine is exhibiting this problem?

    Additional Information:
    I purchased a BYCNC kit back in 2009 with an approximate cutting area of 2' X 4'. I later changed out the Z-Axis Motor and controller for a larger one and have two X-axis motors and controllers. In 2010 I rebuilt the machine out of birch plywood instead of the particle board that the kit supplied. I sent Patrick pictures to him. The machine never gave me a problem till now.

    Additional Information:
    Thanks for the update. This is Patrick by the way. I answer pretty much all of the Customer Service questions. That machine has given quite a good history.

    Additional Information:
    I love the machine and made a number of samples of my work for my e-commerce site, but I can't start selling product until I know this problem is solved because I will not be able to fulfill orders. I finally got all the electronics out of its enclosed protected area near the machine so that I test each controller as you recommended. I hope the problem can be rectified. Will let you know.

    Additional Information:
    Thanks.

    Additional Information:
    I tested each stepper motor and driver pair individually and they worked so what might be the next step?

    Additional Information:
    Did each stepper motor driver pair work for the full +15 minutes?

    Additional Information:
    Yes, I had them in operation for over 30 minutes.

    Additional Information:
    Ok, well it’s good that the motors and driver are ok. We are now down to the power supply and the breakout board as possible causes for the stop. I have a feeling it may be the power supply where with all three drivers drawing current and the power supply maybe getting too hot. Is the fan in the power supply working? You can also test to see if there is 36 volts on the power supply voltage output (V+ and V-).

    Regarding the breakout board, if you have an oscilloscope, you can test if the driver pulses are outputting, but I would consider this as a last resort after you determine if there is a problem with the power supply.

    Additional Information:
    I tested the power supply with a voltmeter and each output was registering 39-40 volts. I think the problem may be the g-code. I am using V-Carve pro to do design and output to Mach 3 Mill g-code. When I studied the g-code lines I noticed that further into the program the z-axis g-code stopped zeroing out to move to the next part of the carving. In other words both the x and y keep moving and the z just stopped working because there was g-code missing. I think something is missing when the design was converted to g-code. I noticed that when I ran a simpler project it worked without problems so I need to investigate this further.

    Additional Information:
    New Update, Its not the g-code. I started to run the long program and everything was working fine until about 45 minutes into it, all the motors stopped working (but the program was still running) and there was a high pitched hum. When I put my hands on the motors they were all trying to move but it seemed they were all stalled. I turned the power off, gave it a minute and when I turned it back on I was able to move the motors again. Could this be a power supply problem?

    Additional Information:
    It does sound more and more like a power supply problem. Did you test the power supply after the motors stopped?

    Additional Information:
    No, I did not. What should I be looking for.

    Additional Information:
    It’s good that you know the voltage during normal operation, so you have a base understood. If the power supply is the problem, the voltage will be reduced or non existent when measured after the problem.

    Additional Information:
    Also, check to see if the fan is running on the power supply when the motors stop. That may (not absolutely) be an indication.

    Additional Information:
    I'll run another test, check the voltage and fan when the problem occurs and let you know. Thanks for hanging in there with me as we try to resolve the problem.

    Additional Information:
    It’s my pleasure. This service is rarely used and is faster then email. Odd nobody uses it. Any recommendations you can give would be great. No problem using this FAQ to pose ideas as this resolution will be cleaned up later.

    Additional Information:
    It might be that people do not realize you can communicate through the sight like this because they are so used to e-mail and texting. You may want to explain this feature in the customer service section.

    I ran the program this morning and it did not take long before the motors stopped. While operating the voltages for all three motors was 46 volts, when the motors stalled (and again there was a high pitch hum) the voltage went up to 60 volts and the fan on the power supply was operating.

    Additional Information:
    So, the driver work individually, but not all together. There is a high pitch sound when the motors fail. You have noted 60 volts from the power supply and the supply fan remains on. This is a difficult issue to resolve, but it seems to me that your power supply may be bad. The 60v measurement tells me that the current dropped and ohms law tells us that is current drops, volts will rise if the resistance stays the same.

    Additional Information:
    As one last test I am going to test each driver again and let them go through the entire program because it seems that the failure can occur at the beginning or towards the end of the program. When I originally tested ach driver I let them run for about a half an hour and the program takes over an hour to run completely. I just want to make sure that it is not the drivers. I will report back when I finished but as you noted it may be the power supply but I want to make sure.

    Additional Information:
    That’s a great idea.

    Additional Information:
    I just ran the x-axis through the whole program and there was no problem especially since I have two NEMA 23 motors moving that axis. Before I check the Y and Z could having a NEMA 34 on the Z axis with appropriate controller be a problem. I used the larger motor on the z axis because the router I am using is a large 1 1/2 hp. I've run this program in the past with this set-up and have not had a problem.

    Additional Information:
    Having a, say 3.0 amp driver, driving a stepper motor that typically requires a 6 amp driver would not seem to be an issue since the driver is limiting the current draw, but the driver may not be able to handle larger coil and back EMF with the protection on the 3.0 amp driver. With that said, I don’t believe that is the issue in this case.

    Additional Information:
    I don't either because I was able to run this and other complicated programs with this set-up in the past. I will let you know on the y and z axis.

    Additional Information:
    Thanks

    Additional Information:
    I ran the Y axis and z axis separately through the entire program and there was no stopping or problem. I guess the culprit is the power supply and I'll order a new one and hope that resolves the problem.

    Additional Information:
    Yes, that is the most probable cause. Please keep me informed. Thanks!

    Additional Information:
    Received and installed the new power supply. I ran the program with the router on and it worked flawlessly. The program runs for an hour and a half and I did not have a single problem. I guess it was the power supply but I was glad to go through all the diagnostics we discussed before replacing it. I hope this power supply lasts a lot longer than the last one. Thanks much for hanging in there with me and coming up with the solution.

    Additional Information:
    It’s my absolute pleasure and I am so happy to hear that the power supply replacement solved the problem.

    Additional Information:


    Additional Information:
    Y axis stop working X & Z work fine Y axis has two motors have check wiring & connections new breakout board still the same port & Pin set OK dont no were to go next David

    Additional Information:


    Additional Information:
    my cnc plasma cutter will run out the program when cutting. what is the cause?

    Additional Information:
    The cnc plasma question shod be a separate question. Can you pise that question by clicking the customer service live menu button at the top? Thanks.

    Click the link to respond:
    What causes one of my two x-axis motors to stop while the Mach 3 program is still running?

  • WHAT CAUSES ONE OF MY TWO AXIS MOTORS TO STOP WHILE THE MACH3 PROGRAM IS STILL RUNNING

    If one of your stepper motors decides to stop moving and the others are moving during a CNC milling or laser cutting job, then there could be two things that could be causing this.

    - The motor found its limiting torque (usually comes with a not-so-pleasant sound). This is where the control software is trying to move the stepper motor too fast (velocity, or too fast too quickly, acceleration) and the load against the stepper motor (inertia of the machine, or the material against the end mill while milling). Recommended action is to lower the velocity and/or acceleration, and/or lower the feedrate when cutting.

    - There is a wiring issue with the wiring from the driver to the motor. This could be a loose wire, or a chafed wire (or two shorting together). It can also be a loose digital wire from the controller board to the driver. Sometimes wire ties can be the culprit. Recommended action would be to thoroughly inspect the wiring.

    It's probably not the limit switches since that would cause a stop to the entire motion of the cnc router or laser machine.

    Sometimes Mach3 will show a status when something goes wrong, but in cases where the motor is stopping due to its torque limit, then that would not be shown in the status. It's always good to check it anyway.

    Additional Information:
    I need to clarify my situation a little better after going to my shop and trying to run another program on Mach 3. About 15 minutes into the milling process all the motors (2-X axis, Y axis and Z axis)stop but the program continues to run. I stop the program and after a couple of minutes when I try to restart the program all the motors start working again. Then after another 15 minutes or so, all the motors stop again. I checked and rechecked my wiring. This has never happened to me before when running the same programs with the same setups and motor speeds. All of a sudden when I reloaded a program I successfully used before it does this. Do you have any recommendations?

    Additional Information:
    Yeah, it sounds like a more complex issue. Have you tried running in the air without using the spindle. This may be a power related issue.

    Additional Information:
    That's exactly what I did. I ran the program without the router motor on just to see if the motors would get through the whole program but they stopped working after about fifteen minutes and then I was able to start them again after about 3 or 4 minutes. I never had this problem before so you can imagine my frustration especially after ruining a couple of projects on expensive material.

    Additional Information:
    Sure. I can completely understand. Try this: disconnect all but one of the driver from power and digital connection and do the air run. Repeat this for each driver and note your findings. This will rule out the drivers causing a power failure.

    Also, is your stepper motors and drivers on a separate power circuit from the computer?

    Additional Information:
    I will try disconnecting each driver and digital connection, which will be a real pain because it will be hard to access.

    All the stepper motors, drivers and computer are plugged into the same power strip.

    Additional Information:
    Ok, so there is no power failure going on, but I believe it is necessary to test each stepper motor and driver pair individually. Hopefully that will lead to a conclusion.

    Additional Information:
    It will take a little time but I will do it and report back on my findings.

    Additional Information:
    Curious, what machine is exhibiting this problem?

    Additional Information:
    I purchased a BYCNC kit back in 2009 with an approximate cutting area of 2' X 4'. I later changed out the Z-Axis Motor and controller for a larger one and have two X-axis motors and controllers. In 2010 I rebuilt the machine out of birch plywood instead of the particle board that the kit supplied. I sent Patrick pictures to him. The machine never gave me a problem till now.

    Additional Information:
    Thanks for the update. This is Patrick by the way. I answer pretty much all of the Customer Service questions. That machine has given quite a good history.

    Additional Information:
    I love the machine and made a number of samples of my work for my e-commerce site, but I can't start selling product until I know this problem is solved because I will not be able to fulfill orders. I finally got all the electronics out of its enclosed protected area near the machine so that I test each controller as you recommended. I hope the problem can be rectified. Will let you know.

    Additional Information:
    Thanks.

    Additional Information:
    I tested each stepper motor and driver pair individually and they worked so what might be the next step?

    Additional Information:
    Did each stepper motor driver pair work for the full +15 minutes?

    Additional Information:
    Yes, I had them in operation for over 30 minutes.

    Additional Information:
    Ok, well it’s good that the motors and driver are ok. We are now down to the power supply and the breakout board as possible causes for the stop. I have a feeling it may be the power supply where with all three drivers drawing current and the power supply maybe getting too hot. Is the fan in the power supply working? You can also test to see if there is 36 volts on the power supply voltage output (V+ and V-).

    Regarding the breakout board, if you have an oscilloscope, you can test if the driver pulses are outputting, but I would consider this as a last resort after you determine if there is a problem with the power supply.

    Additional Information:
    I tested the power supply with a voltmeter and each output was registering 39-40 volts. I think the problem may be the g-code. I am using V-Carve pro to do design and output to Mach 3 Mill g-code. When I studied the g-code lines I noticed that further into the program the z-axis g-code stopped zeroing out to move to the next part of the carving. In other words both the x and y keep moving and the z just stopped working because there was g-code missing. I think something is missing when the design was converted to g-code. I noticed that when I ran a simpler project it worked without problems so I need to investigate this further.

    Additional Information:
    New Update, Its not the g-code. I started to run the long program and everything was working fine until about 45 minutes into it, all the motors stopped working (but the program was still running) and there was a high pitched hum. When I put my hands on the motors they were all trying to move but it seemed they were all stalled. I turned the power off, gave it a minute and when I turned it back on I was able to move the motors again. Could this be a power supply problem?

    Additional Information:
    It does sound more and more like a power supply problem. Did you test the power supply after the motors stopped?

    Additional Information:
    No, I did not. What should I be looking for.

    Additional Information:
    It’s good that you know the voltage during normal operation, so you have a base understood. If the power supply is the problem, the voltage will be reduced or non existent when measured after the problem.

    Additional Information:
    Also, check to see if the fan is running on the power supply when the motors stop. That may (not absolutely) be an indication.

    Additional Information:
    I'll run another test, check the voltage and fan when the problem occurs and let you know. Thanks for hanging in there with me as we try to resolve the problem.

    Additional Information:
    It’s my pleasure. This service is rarely used and is faster then email. Odd nobody uses it. Any recommendations you can give would be great. No problem using this FAQ to pose ideas as this resolution will be cleaned up later.

    Additional Information:
    It might be that people do not realize you can communicate through the sight like this because they are so used to e-mail and texting. You may want to explain this feature in the customer service section.

    I ran the program this morning and it did not take long before the motors stopped. While operating the voltages for all three motors was 46 volts, when the motors stalled (and again there was a high pitch hum) the voltage went up to 60 volts and the fan on the power supply was operating.

    Additional Information:
    So, the driver work individually, but not all together. There is a high pitch sound when the motors fail. You have noted 60 volts from the power supply and the supply fan remains on. This is a difficult issue to resolve, but it seems to me that your power supply may be bad. The 60v measurement tells me that the current dropped and ohms law tells us that is current drops, volts will rise if the resistance stays the same.

    Additional Information:
    As one last test I am going to test each driver again and let them go through the entire program because it seems that the failure can occur at the beginning or towards the end of the program. When I originally tested ach driver I let them run for about a half an hour and the program takes over an hour to run completely. I just want to make sure that it is not the drivers. I will report back when I finished but as you noted it may be the power supply but I want to make sure.

    Additional Information:
    That’s a great idea.

    Additional Information:
    I just ran the x-axis through the whole program and there was no problem especially since I have two NEMA 23 motors moving that axis. Before I check the Y and Z could having a NEMA 34 on the Z axis with appropriate controller be a problem. I used the larger motor on the z axis because the router I am using is a large 1 1/2 hp. I've run this program in the past with this set-up and have not had a problem.

    Additional Information:
    Having a, say 3.0 amp driver, driving a stepper motor that typically requires a 6 amp driver would not seem to be an issue since the driver is limiting the current draw, but the driver may not be able to handle larger coil and back EMF with the protection on the 3.0 amp driver. With that said, I don’t believe that is the issue in this case.

    Additional Information:
    I don't either because I was able to run this and other complicated programs with this set-up in the past. I will let you know on the y and z axis.

    Additional Information:
    Thanks

    Additional Information:
    I ran the Y axis and z axis separately through the entire program and there was no stopping or problem. I guess the culprit is the power supply and I'll order a new one and hope that resolves the problem.

    Additional Information:
    Yes, that is the most probable cause. Please keep me informed. Thanks!

    Additional Information:
    Received and installed the new power supply. I ran the program with the router on and it worked flawlessly. The program runs for an hour and a half and I did not have a single problem. I guess it was the power supply but I was glad to go through all the diagnostics we discussed before replacing it. I hope this power supply lasts a lot longer than the last one. Thanks much for hanging in there with me and coming up with the solution.

    Additional Information:
    It’s my absolute pleasure and I am so happy to hear that the power supply replacement solved the problem.

    Additional Information:


    Additional Information:
    Y axis stop working X & Z work fine Y axis has two motors have check wiring & connections new breakout board still the same port & Pin set OK dont no were to go next David

    Additional Information:


    Additional Information:
    my cnc plasma cutter will run out the program when cutting. what is the cause?

    Additional Information:
    The cnc plasma question shod be a separate question. Can you pise that question by clicking the customer service live menu button at the top? Thanks.

    Click the link to respond:
    WHAT CAUSES ONE OF MY TWO AXIS MOTORS TO STOP WHILE THE MACH3 PROGRAM IS STILL RUNNING

  • From the BOB how can I reverse one of my steppers - i'm running 2 on my Y Axis

    When trying to use two motors on a single axis, there is a multitude of methods to get them to work together.
    First: There should always be a slave option in the CNC control software(mach 3/ planet-cnc/emc2/etc.), this will be the easiest way to make the dual motor configuration work. However some adjusting might be necessary due to the orientation of the motor when mounting it on the opposite side of the CNC machine.(Mach3/config/slaveaxis, planet-cnc/file/settings/axes).

    Secondly: Dealing with our interface boards(maybe third-party as well), you can have two drivers going to the same axis on the interface board. Which then will have one motor per driver, this will use the same motion and control from the (ex.) x-axis to driver two motors. However some adjusting might be necessary due to the orientation of the motor when mounting it on the opposite side of the CNC machine.

    Adjusting of the driver or motor wires, can be done separate from the control software with the use of a hex inverter, that can be used and to switch the signal (ex. takes a low signal and brings it high, and takes a high signal and brings it low) of one of the motors, to run the same as the other motor.
    There is also another method of inverting the orientation of the motors movement without the use of a hex inverter. This method you will have to wire the coil's of the motors oppositely of what is recommended for one of the motors. Example, you will wire our Nema 24 as follows(recommended): A+ - red/blue, A- - yellow/black, B+ - white/brown, B- - green/orange. However to run another motor with with it you will have to switch the A/B connections to: A+ - white/brown, A- - green/orange, B+ - red/blue, B- - yellow/black.

    These method's are usually needed/used when trying to control two motors and setting it up without the help of the CNC control software, and also due to the mounting orientation of the second motor, the inverting the direction of motion will be necessary so they work together instead of working against each other.

    Click the link to respond:
    From the BOB how can I reverse one of my steppers - i'm running 2 on my Y Axis

  • Are the stepper motors on x and y axis suppose to be hot after running for approximately 30 min. I can touch them but they are hot.

    If your motors are hot to the touch, this is normal. Current is being drawn by the motor coils as the motor moves and as the motor stays at a position. If the motor is not using the current in the coils to move (holding it's position), the energy will be translated as heat (rather than motion, sound or light). Even while moving, some of the energy will be lost as heat. Remember that energy cannot be created nor destroyed.

    Click the link to respond:
    Are the stepper motors on x and y axis suppose to be hot after running for approximately 30 min. I can touch them but they are hot.

  • I am interested in purchasing the Green Lean complete kit and also buy the ArtCamPro what other software will I need to up and running?

    If you were to buy all of that, only thing you'll need is the mach3 software to run the machine.

    Click the link to respond:
    I am interested in purchasing the Green Lean complete kit and also buy the ArtCamPro what other software will I need to up and running?

  • What tolerance can I expect from your largest cnc machine and the laser cutter? Also, what depth can I get on the z axis?

    The largest CNC machine we make at this time (12/04/2015) is the GreenBull 6'x12' model. This model has 2 options for Z-axis travel.

    The short-z option has a total Z travel of 5.75 inches. From that you would subtract the length of the end mill used and the thickness of the spoil board to determine the maximum material thickness. (Example: If the end mill extends 1.25" from the collet and the spoil board is .75", then the material could be up to 5.75 - 1.25 - 0.75 = 3.75 inches in thickness). This is good for most sheet-type materials.

    The long-z option, used mainly for large 3D carvings, requires a custom frame and allows for up to 36" of travel.

    The tolerance of our machines, like any machine, depends on several variables. The major variables include the manufacturing tolerance, the type of machine control used, the precision of assembly, the thoroughness of maintenance, and the initial and ongoing calibration of the machine. Because we sell kits only most of these variables are outside our control. Therefore, we are hesitant to guarantee a certain level of tolerance for an end user. However, in our experience, tolerances of .001" are readily achievable with our machines.

    Click the link to respond:
    What tolerance can I expect from your largest cnc machine and the laser cutter? Also, what depth can I get on the z axis?

  • What do I need to purchase from you to get me running. I have planet cnc control board but it is difficult contacting them when I need help.

    Software specific questions for Planet-CNC will have to come from them or other sources as we are not fully equipped to troubleshoot all issues. If the issue is related to motor tuning or setup involving our electronics, then we will gladly assist you. You may contact techsupport@buildyourcnc.com with inquiries.

    Click the link to respond:
    What do I need to purchase from you to get me running. I have planet cnc control board but it is difficult contacting them when I need help.

  • Going to purchase a new laptop computer. Question. What is the minimal requirement for laptops running cnc planet software and other softwares that are needed?

    Your purchase of a laptop will depend on what CNC software and CNC interface you will be using. In most cases, CNC interfaces use a parallel port, or the interface will convert USB instructions into a form of parallel I/O pins. We provide both types of interfaces, but you will be required to use specific software packages compatible with the interface. The USB interface that we sell at the moment is only compatible with Planet-CNC software (which is very good software), and if the computer has a parallel port, you will have your choice of many software titles including (but not limited to) Mach3 and LinuxCNC.

    The hardware and processing performance is not as important. Computers with relatively slow processors (i.e. Pentium) can control a CNC machine and achieve good performance.

    If you intend using CAD and CAM on that computer, then you will want a more modern computer that will have a good amount of memory and processing power. You will need to refer to the software requirements for the minimum specifications.

    Click the link to respond:
    Going to purchase a new laptop computer. Question. What is the minimal requirement for laptops running cnc planet software and other softwares that are needed?

  • I am building a machine that requires 2 steppers to drive the Y axis, can you make me a redleaf system using the 651oz steppers that will work for me?

    Yes, we can make a redLeaf system that has all 6A drivers for use with the 651 oz-in motors. We can also wire the electronics in a way that two of the drivers will use the pins of the same axis so that axis will drive two drivers and motors.

    Click the link to respond:
    I am building a machine that requires 2 steppers to drive the Y axis, can you make me a redleaf system using the 651oz steppers that will work for me?

  • Is a cahin driven y axis that is six feet feesable? What is the best setup other than ballscrew?

    The main reason why we chose a chain driven CNC machine is to keep cost down, and works perfectly! It is also pretty simple to setup, so in your application it is feesable!
    We currently have our largest CNC machine (greeBull 6X) which runs roller chain for both the X-axis(12Ft.) and Y-axis(6Ft.).

    In longer lengths the Lead Screw, and Ball Screw will be hard to get in those lengths without any bends or having it perfectly straight at a low cost, and maybe be harder to accomplish.
    Most larger CNC machines, will have to use rack and pinion for the larger lengths, which will have a more complex assembly.
    Both the ball screw and rack and pinion will both run (mostly) on aluminum machines.

    Click the link to respond:
    Is a cahin driven y axis that is six feet feesable? What is the best setup other than ballscrew?

  • I AM USING A XYLOTEX 3 AXIS BOARD AND WANT TO ADD ANOTHER MOTOR SLAVED THE X-AXIS. WILL DRIVE CW230 WORK?

    If the pins from the terminal block on the side of the board are outputs, or at least 2 of them are outputs, then you can connect our modular driver to the board (example: cw230). If they are all inputs, then you would not be able to connect an external driver.

    Click the link to respond:
    I AM USING A XYLOTEX 3 AXIS BOARD AND WANT TO ADD ANOTHER MOTOR SLAVED THE X-AXIS. WILL DRIVE CW230 WORK?

  • Are there .dxf files or other files for the MDF parts in Combo #1 so that they may be cut using a CNC?

    No, at this time, we do not offer any .dxf or any other type of file to cut the pieces for the DIY Combo #1. Just the directions that you are already able to access with the dimensions in them.

    Additional Information:

    Click the link to respond:
    Are there .dxf files or other files for the MDF parts in Combo #1 so that they may be cut using a CNC?

  • Will Mach3 USB Interface board fit in my redleaf, in lieu of the breakout board that came with it?

    The Mach3 USB board will fit in the redLeaf, but you may need to modify the Plexiglas top for proper mounting. However, the redLeaf has the proper parallel GPIO on the motherboard for use with the Parallel breakout board. If you have a laser on the machine you are using, then I would urge you to maintain the parallel breakout board as the Mach3 USB board will not work correctly using the Z-direction pin and you will need to determine how to use the output pins onthe USB board to ensure proper laser functionality.

    Click the link to respond:
    Will Mach3 USB Interface board fit in my redleaf, in lieu of the breakout board that came with it?

  • I am looking at 2 of your drivers. 1 is the 1/64 step and the other is 1/256. What is the difference between the two?

    Stepper motors are designed to move in specific increments; these increments are called "steps". For example, a common standard is for 200 steps per full revolution. Microstepping is a method to send signals to the motor to move only a fraction of a full step at a time. For example, if a motor has 200 steps per revolution and is microstepped 1/16, then effectively there are 3200 small step movements (microsteps) per revolution instead of 200 larger ones. This makes the motion of the motor much smoother and more precisely controllable, at the cost of decreased holding torque.

    Here are is a good references for stepper motor theory: http://users.ece.utexas.edu/~valvano/Datasheets/StepperMicrostep.pdf

    And Wikipedia has a good overview as well:
    https://en.wikipedia.org/wiki/Stepper_motor

    Click the link to respond:
    I am looking at 2 of your drivers. 1 is the 1/64 step and the other is 1/256. What is the difference between the two?

  • For tuning the motors in mach 3 should I be running a gcode or is keyboard jogging enough to determine the stall rates

    It seems to be getting some kind of interference or a short within the wiring or communication, try jogging the motors in the software without anything wired to the board. Then add one motor at a time to see if there is a short within your wiring or a faulty driver/motor.
    If the USB breakout board continues to move the x-axis with no motors or driver wired to it, please email customerservice@buildyourcnc.com for a replacement or further troubleshooting.

    Click the link to respond:
    For tuning the motors in mach 3 should I be running a gcode or is keyboard jogging enough to determine the stall rates

  • For tuning the motors in mach 3 should I be running a gcode or is keyboard jogging enough to determine the stall rates

    Keyboard jogging will give you a good start at motor tuning since going from a stop to rapid travel speed is the quickest the machine will be required to accelerate. However, best practice is to also run test files and actually cut the type of materials you expect to deal with to test machine performance under load and make any fine adjustments needed for maximum performance.

    Click the link to respond:
    For tuning the motors in mach 3 should I be running a gcode or is keyboard jogging enough to determine the stall rates

  • What else to I need to purchase along with the "3 Axis Electronics Combo w/ USB Interface Board" to get the electronics up and running? (software, 5V power supply, 4-conductor wire, etc.)

    Here is a list of the parts needed to get the electronics combo functioning (parallel or USB interface options):

    - 22 or 24 gauge stranded hookup wire to connect all of the drivers to the USB or parallel interface (terminal to terminal connections),
    - 18 gauge stranded hookup wire to connect the drivers to the power supply,
    - a power cable (extension cord) to connect from the power outlet to the power supply,
    - 4 conductor cable to connect the drivers to the stepper motors,
    - a USB cable to connect from the computer to the USB interface (or for power to the parallel interface),
    - for the parallel interface, a parallel cable is needed (male to male db-25),
    - a computer (for parallel interface, the computer will need a parallel port and if the computer does not contain a parallel interface, the motherboard may have a header for it, or you can purchase a parallel adapter to plug into the motherboard, very inexpensive),
    - cnc control software: for the USB interface, you will need planet-cnc software, for the parallel interface, you can use any industry standard cnc control software (the typical is Mach3 for Windows, or EMC2 or Linuxcnc for Linux (Linuxcnc.org).

    5v power supply is not needed. The 5 volts signal level power is derived from the computer through USB on both types of interfaces.

    Click the link to respond:
    What else to I need to purchase along with the "3 Axis Electronics Combo w/ USB Interface Board" to get the electronics up and running? (software, 5V power supply, 4-conductor wire, etc.)

  • what ports do i connect my computer to on a redleaf system that has Windows Mach3 installed?

    The redLeaf system features an integrated CNC computer preinstalled with Windows and mach3. You should only need to connect a monitor/keyboard/mouse for functionality.

    Click the link to respond:
    what ports do i connect my computer to on a redleaf system that has Windows Mach3 installed?

  • The motherboard on the computer I bought from you went out. What would you suggest. I have a laptop, could I use it and use a Mach3 USB interface board?

    Yes, you can use a laptop if you have a controller that uses a USB, like the Mach3 USB card. If you don't have that, you can purchase that part here:
    https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

    If you have a controller board that connects to a 25 pin connector, modern laptops will not be able to connect to that port.

    How old is your CNC computer system?

    Additional Information:
    The CNC computer system is 2013 (5 years). The built in video card went out. I will order the Mach3 USB card. Thank you.

    Additional Information:
    You're welcome

    Click the link to respond:
    The motherboard on the computer I bought from you went out. What would you suggest. I have a laptop, could I use it and use a Mach3 USB interface board?

Get Help with:
This Product
Orders
Tech Support
Sales
This Product
Order Query
Tech Support
Sales
Not logged in. Log In Register
Track Order(s)
View Order(s)
I Want to Schecule a One-On-One Paid Tech Support Session
Book an Appointment Pertaining to a BuildYourCNC Product (Free)
Ask a Quesion Below (Free):
Book an Appointment Pertaining Other Equipment ($60/half hour)
Book an Immedite Appointment Pertaining Other Equipment ($120/half hour)
Ask a Quesion Below (Free):
Waiting for response... I may not answer immediately, but I was notified on my cellular phone so my response is forthcoming. If I don't respond immediately, you can always go to the [My Account] page to see all of our chats at any time.