[ Log In ]
[ Register ]
NEW: CNC Router PLANS Available for all of our Newest CNC Models!! Click here to "Design Your CNC".

Question #: 13251

Question: What are your terms and conditions for financing?

Current Solution

We work with banks who will process financing requests. For more information about submitting an application for financing please contact sales@buildyourcnc.com

Respond:

Other Possible Solutions to this Question

  • What are the fault conditions of the DM556 and DM542 drivers?

    There are three main LED fault signals that the DM556 and DM442 drivers exhibit. There is a red and green LED. The red LED will show the fault signals.

    The fault signals are:

    - Over-Current: If there is continuous current that is above 16 amps, the Red LED will flash every three seconds. Over-current could be related to: a short in the motor coils, or two of the wires of the motor are shorted; of the motor wires/coil is shorted to ground.

    - Over-voltage: If the power supply output to the driver exceeds a voltage of 52 volts, the red LED will flash twice every three seconds.

    - Phase Error: Is the motor wires are not connect, or they are connected incorrectly, the red LED will flash four times every three seconds.

    Click the link to respond:
    What are the fault conditions of the DM556 and DM542 drivers?

  • What size forstner are used in the book build your own cnc

    That was a very long time ago, but I think I was using 3/4". You can use a size just larger than the outer width of the nut.

    Click the link to respond:
    What size forstner are used in the book build your own cnc

  • What are the model numbers for your 2.2kw 110v and 220v VFDs? Or can you share a link to their documentation?

    Documentation for Parameter setup is included with VFD purchase. For spindle wiring and programming, please refer to the product pages for the spindles or VFDs (or the combo kit) and scroll down to instructions. For further assistance you can contact customerservice@buildyourcnc.com

    Click the link to respond:
    What are the model numbers for your 2.2kw 110v and 220v VFDs? Or can you share a link to their documentation?

  • Hi does your company offer financing?

    For financing option, you can use the Bill Me Later feature offered by PayPal.

    Click the link to respond:
    Hi does your company offer financing?

  • I'm new to CNC and just finish building my router.I need software for my post processor and not sure if your product is what I need?

    You will need a CNC software that will control your router cnc machine, and your design CAD/CAM software will need to know the CNC software you plan on using so the post processor in the CAM software can create the g-code for the CNC control software. So if you have for example, Mach 3 and our parallel breakout board, you can use the Mach 3 post processor in your design software.

    Click the link to respond:
    I'm new to CNC and just finish building my router.I need software for my post processor and not sure if your product is what I need?

  • what are the dimensions and model number of the 3/8" ID roller bearings on your website?

    The specifications for our 3/8" bearings are R6ZZ. The ZZ means double metal shielded. The metal shielding is to protect the ball bearings between the inner race and outer race.

    Inside diameter: 3/8"
    Outside Diameter: 7/8"
    Width: 9/32"

    Click the link to respond:
    what are the dimensions and model number of the 3/8" ID roller bearings on your website?

  • how long are your lead screws 3/8 and how much ? looking for 3/8 see my previous question what is the minimum length and how much per inch
  • I'm selecting a vacuum for dust collection (greenLean). What works well in terms of HP and gallons of bin capacity?

    We use the Ridgid wet/dry vacuums in our shop. If you get the larger capacity that also come with a 6.0 HP motor seem to be a good fit and is relatively quiet. We also use two vortex type mechanisms in-line before the vacuum to get the big chips (first one) and the dust (second one) so the filter does not get clogged in the vacuum. Since we have been using this system, the vacuum will not contain any chips or dust which will provide 100% of vacuum suction throughout the entire machining process.

    https://www.ridgid.com/us/en/wet-dry-vac

    Click the link to respond:
    I'm selecting a vacuum for dust collection (greenLean). What works well in terms of HP and gallons of bin capacity?

  • what are all the settings i'd need for mach3 for use with a blackfoot and a redfly?

    These are the recommend values(default) for our blackFoot CNC machine, the acceleration and velocity can be adjusted as high as the motor can rotate without stalling! Suggested increment's will be by 10's.

    blackFoot:
    X-axis
    “CW8060 (6.0A) Driver”
    Set to 1/16 Microstep, 5.43A
    Dipswitches: 01100110 (“0”=down, “1”=up)
    Mach3 Motor Tuning: 914.29 steps/in, Velocity 400.02, Acceleration 4
    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in, Velocity 400.02, Acceleration 4
    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in, Velocity 79.98, Acceleration 5

    Additional Information:
    how can we tuning the CNC motor

    Click the link to respond:
    what are all the settings i'd need for mach3 for use with a blackfoot and a redfly?

  • What is the z-axis travel for your largest machine?

    The largest CNC machine we make at this time (12/04/2015) is the GreenBull 6'x12' model. This model has 2 options for Z-axis travel.

    The short-z option has a total Z travel of 5.75 inches. From that you would subtract the length of the end mill used and the thickness of the spoil board to determine the maximum material thickness. (Example: If the end mill extends 1.25" from the collet and the spoil board is .75", then the material could be up to 5.75 - 1.25 - 0.75 = 3.75 inches in thickness). This is good for most sheet-type materials.

    The long-z option, used mainly for large 3D carvings, requires a custom frame and allows for up to 36" of travel.

    Click the link to respond:
    What is the z-axis travel for your largest machine?

  • If I build a Laser with the components on this site, can I cut the 0.1mm and 0.2mm board? Is it cut in optimal conditions, or if not what you recommend ?!

    What material is the 0.1mm and 0.2mm board?

    Additional Information:
    Steel sheet


    Additional Information:
    Steel Sheet

    Additional Information:
    Thanks for the response. CO2 lasers unfortunately cannot cut metallic materials. Metals are best cut with other types of lasers, or by using oxygen assist. The oxygen assist method is not encourages as the combination or CO2 laser and oxygen is very volatile.

    Additional Information:
    and I can not do this laser to cut the steel plate, but instead of the CO2 tube I put the oxygen tube, or do not I know ?! Do I have a chance in the products on the site to create a laser for 0.1mm and 0.2mm steel sheets?

    Additional Information:
    I can help with an answer, Thanks!

    Additional Information:
    I can help with an answer, Thanks!

    Additional Information:
    Can you help me with an answer? Thank you! **

    Click the link to respond:
    If I build a Laser with the components on this site, can I cut the 0.1mm and 0.2mm board? Is it cut in optimal conditions, or if not what you recommend ?!

  • WHAT CAUSES RINGING IN YOUR EAR AND HOW CAN YOU STOP IT?

    Tinnitus . Learn to love it. No really you should see a doctor. Make sure. White noise will help you sleep when it gets loud.

    Additional Information:
    I learned, too late, that if a sudden loud event causes tinnitus, see an audiologist IMMEDIATELY. They can do something about it if addressed within a day or so.

    Wear hearing protection...always. Loud noises trigger my tinnitus, and headphones and ear plugs (when out & about or at the movies, subway, etc) help tremendously. Mine are rated 33dB.

    Click the link to respond:
    WHAT CAUSES RINGING IN YOUR EAR AND HOW CAN YOU STOP IT?

  • What are the tolerances of your machines?

    The tolerance of our machines, like any machine, depends on several variables. The major variables include the manufacturing tolerance, the type of machine control used, the precision of assembly, the thoroughness of maintenance, and the initial and ongoing calibration of the machine. Because we sell kits only most of these variables are outside our control. Therefore, we are hesitant to guarantee a certain level of tolerance for an end user. However, in our experience, tolerances of .001" are readily achievable with our machines.

    Additional Information:
    What is the likely tolerance one could achieve without continual frustration and months of tinkering?

    Additional Information:
    We actually do very little tinkering with our production machine. The wood has a very small coefficient of linear expansion as compared to metals and plastic, so calibration is reduced to a very infrequent state.

    As with all machines, the determination of backlash in all parts of the machine is important, managing the tightening of these points of adjustment is necessary, but are still done infrequently.

    Click the link to respond:
    What are the tolerances of your machines?

  • Under what conditions should the LED on the 3d printer driver be lit when the driver is connected to the MB?

    The driver's LED serves to indicate a fault condition. The driver chip has built in protection for overheating and over current. If the LED is on, most likely, the driver will stop until the condition is resolved. If you see the LED on, adjust the vref trimmer. First, connect a multimeter to the pads just next to the trimmer potentiometer and adjust until the voltage is lowered a bit. Alternatively, even though the PCB contains a vast amount of thermal vias and a relatively large ground plane connected to the belly of the driver, there still may be a need to cool the driver chip using a small heat sink. Do this only if you are not satisfied with the performance of the motor at the torque require.

    Click the link to respond:
    Under what conditions should the LED on the 3d printer driver be lit when the driver is connected to the MB?

  • What file types can your laser cutter and engraver accept?

    LaserCAD and the Anywells Laser Controller used in our BlackTooth and Vertical Laser XL laser cutters and engravers can accept these file types:

    .nc (Gcode)
    .ai (Adobe Illustrator)
    .svg
    .pdf (Adobe Acrobat)
    .dxf (AutoCAD and Drawing Exchange)
    .plt
    .dst
    .dsb
    .uds (UD)
    .bmp (Bitmap image)
    .gif (Image)
    .jpg (Joint Photographers)
    .png

    Click the link to respond:
    What file types can your laser cutter and engraver accept?

  • how long are your lead screws 3/8 and how much ? looking for 3/8 see my previous question

    We currently only stock 2 start lead screw for the 3/8".

    Click the link to respond:
    how long are your lead screws 3/8 and how much ? looking for 3/8 see my previous question

  • What is your largest format cnc router

    The largest CNC machine we make at this time (12/04/2015) is the GreenBull 6'x12' model. This model has 2 options for Z-axis travel.

    The short-z option has a total Z travel of 5.75 inches. From that you would subtract the length of the end mill used and the thickness of the spoil board to determine the maximum material thickness. (Example: If the end mill extends 1.25" from the collet and the spoil board is .75", then the material could be up to 5.75 - 1.25 - 0.75 = 3.75 inches in thickness). This is good for most sheet-type materials.

    The long-z option, used mainly for large 3D carvings, requires a custom frame and allows for up to 36" of travel.

    Click the link to respond:
    What is your largest format cnc router

  • what does the plans, hardware, electronics and mechanical option consists of for a CNC router?

    The plans/hardware/electronics/mechanical includes everything but the wood structural components that can be cut by the customer. This plans/hardware option includes all of the electronics, like motors, drivers, controller, and all of the cables and wires to connect all of the electronics together. The mechanical components include shafts, couplings, linear rails, bearing blocks, sprockets, lead screws, etc. The hardware consists of all of the screws nuts, insert nuts, cross dowels, etc, to assemble all of the structural, mechanical, and electronics together.

    Click the link to respond:
    what does the plans, hardware, electronics and mechanical option consists of for a CNC router?

  • What output pins on your BOB are used to control the SuperPID?

    Yes, you can use any two of the output terminals of the breakout board to control the SuperPID closed loop router controller (a diagram is not needed with these instructions).

    One output terminal will be used as an on/off (1/0 or 5v/gnd) that will be invoked with the M3/M4/M5 M-codes in your g-code instructions.

    The other terminal will be connected to either another 5v/gnd signal to control speed for 5000/20000 rpm or for PWM output (recommended) for proportional speed control.

    To setup this configuration in Mach3, go to your ports and pins dialog box (config menu -> ports and pins). Click on the spindle setup tab. In the Motor Control Section of the dialog, check the box for Use Spindle Motor Output and check the box for PWM control. Change the PWM Base Frequency to 50Hz.

    Click the link to respond:
    What output pins on your BOB are used to control the SuperPID?