[ Log In ]
[ Register ]

Question #: 13327

Question: Y-Axis on Controller Not Working

Current Solution

When I switch the driver to Z or X axis it works fine, but Y gets no response. I'm using the Planet CNC driver and software (latest versions).

Additional Information:


Additional Information:


Additional Information:


Additional Information:

Respond:

Other Possible Solutions to this Question

  • Can I add a fourth axis by just adding another controller?

    In generally, you would only need a driver to drive the motor on the 4th axis.

    A fourth (4th) axis can be added using a head stock that contains a motor where the motor turns a chuck that holds the object. The motor requires a driver that is controlled by an interface card such as the parallel breakout board, or the usb controller board. Our 4th Axis head stock can be driven by our standard 3.0 amp driver.

    The software used to control the 4th axis would need to be able to control 4 axes (X, Y, Z and A). Mach3, LinuzCNC and Planet-CNC are good examples of control software that can control more than 3 axes.

    Click the link to respond:
    Can I add a fourth axis by just adding another controller?

  • Requirement of laser cutting CNC Router having working area: 100cm x 100cm x 300cm, Belt driven motion, servo motor controller

    This is an open ended question to which there could be many possible answers.

    The requirement of a laser cutter is having a laser with enough energy output to cut the intended material. Generally, the laser function is not tied to the working area unless the laser tube is stationary, where the farther the beam has to travel, the less energy results at the intended area (on the surface of the material).

    We don't use servo motors here. Rather, we use precision stepping motors instead.
    https://buildyourcnc.com/category/nema

    We do offer timing belts.
    https://buildyourcnc.com/category/pulley

    Our blackTooth Laser Cutter:
    https://buildyourcnc.com/blackToothLaserCutterAndEngraver.aspx

    Our greenBull Leaser/Spindle Head:
    The CNC Machine: https://buildyourcnc.com/greenBullCNCMachineKit.aspx
    The Laser/Spindle Head: https://buildyourcnc.com/item/cnc-machine-laser-spindle-combo-head

    Click the link to respond:
    Requirement of laser cutting CNC Router having working area: 100cm x 100cm x 300cm, Belt driven motion, servo motor controller

  • do you not have a usb controller for planet cnc since yours is discontinued

    Unfortunately not. As much as we like the Planet-CNC software and control, they made a change in their Planet-CNC software that eliminates support for our board.

    Click the link to respond:
    do you not have a usb controller for planet cnc since yours is discontinued

  • Laser Controller Password?

    The current model laser controller that we sell is the AWC608 Laser Controller, and the password is 608.

    Our current testing model PH01/02/03(Blue) Laser Controller's password is PHD123.

    Additional Information:


    Additional Information:

    Click the link to respond:
    Laser Controller Password?

  • LASER CONTROLLER PASSWORD?

    What is the model number of the laser controller?

    Additional Information:
    Hey - the model number on the laser controller is
    AWC708C
    S/N:708014243

    Additional Information:
    Do you need any additional information here? I really want to get going on it this weekend!

    Additional Information:
    Sorry about that. If you are referring to the CN1 and CN2 connector, I don't believe it is needed if it didn't come with the connector. The components that we send to the customer is the same package that is sent from the manufacturer of the product. I would try connecting it to the CN1 connector of both units and test the interface (control panel).

    Additional Information:
    The manual for the AWC 708 shows the two ports CN1 and CN2 connected, but that may just be for thorough documentation if the CN2 is needed for some reason. Do you have a copy of the manual or know where to find it? If not, I will put the document link here.

    Click the link to respond:
    LASER CONTROLLER PASSWORD?

  • Laser controller limit switch connection

    If you are using the AWC708 or equivalent laser controller, the limit switches will connect between the EL input terminal and the GND terminal in normally open (NO) connection. Most limit switches can be connected as NO, or normally closed (NC).

    For instance, a limit switch for the X- limit will be connected from the ELX- terminal to the NO connection of the limit switch, then a connection from the GND terminal on the laser controller to the COM connection to the same limit switch.

    Click the link to respond:
    Laser controller limit switch connection

  • 5 AXIS CONTROLLER ISSUES.

    Please visit this link https://buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay#prettyPhoto
    and follow the steps described on the bottom of the page.

    Click the link to respond:
    5 AXIS CONTROLLER ISSUES.

  • Does the Laser Controller work with Mach3?

    The laser Controller will not work with Mach3.

    Click the link to respond:
    Does the Laser Controller work with Mach3?

  • Can I add a relay to the Mach3 USB controller?

    Yes, you can add a relay to the Mach3 USB controller. The relay must be a 24V relay on it's input side and be able to be set to active low. I demonstrate this in a video on the following page:
    https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

    The video is titled: Mach3 USB Controller Outputs

    Click the link to respond:
    Can I add a relay to the Mach3 USB controller?

  • Can the USB CNC Controller be used with LinuxCNC?

    The USB Interface can only be used with the Planet-CNC software which runs under the windows operating system.

    Click the link to respond:
    Can the USB CNC Controller be used with LinuxCNC?

  • Any timing on the USB Controller board for Mach-4

    The board has been developed and we are currently waiting to receive developer info from the makers of Mach4 so we can proceed with testing compatibility. There is no definite time frame but we are hopeful it will be released within the next couple months.

    Click the link to respond:
    Any timing on the USB Controller board for Mach-4

  • how to control the spindle with the usb controller

    To control a spindle using the USB CNC interface, you will need a relay board that contains a transistor that can activate the relay with a power source with enough current that can activate the relay. This video explains all of the information you will need to develop this relay circuit:

    &index=44&list=PLE72E4CFE73BD1DE1

    Click the link to respond:
    how to control the spindle with the usb controller

  • Can I use Mach3 or 4 with your USB controller PCA?

    The USB controller board is currently only compatible with Planet-CNC software.

    Click the link to respond:
    Can I use Mach3 or 4 with your USB controller PCA?

  • Limit switches connect to AWC708c laser controller

    If you are using the AWC708 or equivalent laser controller, the limit switches will connect between the EL input terminal and the GND terminal in normally open (NO) connection. Most limit switches can be connected as NO, or normally closed (NC).

    For instance, a limit switch for the X- limit will be connected from the ELX- terminal to the NO connection of the limit switch, then a connection from the GND terminal on the laser controller to the COM connection to the same limit switch.

    Click the link to respond:
    Limit switches connect to AWC708c laser controller

  • How do I use the outputs on the Mach3 USB controller?

    I created a video to demonstrate how to use the outputs on the Mach3 USB controller. You can find this video on the following page:
    https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

    Scroll down to the 5th video on that page. The title of the video is: Mach3 USB Controller Outputs

    Click the link to respond:
    How do I use the outputs on the Mach3 USB controller?

  • does the pokeys57cnc controller support slaving an axis?

    All controllers actually support slaving as long as there are enough step and direction connections on the controller to allow for either the A, B, or C axis to be used. The feature is set up in Mach3 or Mach4. Under the config menu, you can select the Slave Axis selection and specify the A, B, or C axis as the slave. The A axis is motor connection 4, B is 5 and C is 6. Make sure to set the steps per unit the same as the main axis since Mach will not do this automatically.

    Click the link to respond:
    does the pokeys57cnc controller support slaving an axis?

  • What file types will the anywells laser controller accept?

    LaserCAD and the Anywells Laser Controller used in our BlackTooth and Vertical Laser XL laser cutters and engravers can accept these file types:

    .nc (Gcode)
    .ai (Adobe Illustrator)
    .svg
    .pdf (Adobe Acrobat)
    .dxf (AutoCAD and Drawing Exchange)
    .plt
    .dst
    .dsb
    .uds (UD)
    .bmp (Bitmap image)
    .gif (Image)
    .jpg (Joint Photographers)
    .png

    Click the link to respond:
    What file types will the anywells laser controller accept?

  • How are limit switches connected to the AWC708 controller?

    If you are using the AWC708 or equivalent laser controller, the limit switches will connect between the EL input terminal and the GND terminal in normally open (NO) connection. Most limit switches can be connected as NO, or normally closed (NC).

    For instance, a limit switch for the X- limit will be connected from the ELX- terminal to the NO connection of the limit switch, then a connection from the GND terminal on the laser controller to the COM connection to the same limit switch.

    Click the link to respond:
    How are limit switches connected to the AWC708 controller?

  • how to configure the Z probe using the pokey57cnc controller

    If you do the following, you can get mach3 to recognize the probe.

    In mach3, go to config, ports and pins, input signals, and scroll down to probe. Check enabled, active low, and emulated. Ignore the ports, pins and keys. They are set automatically.



    Go to Mach3 Plugin Control tab, select Configure Pokeys57CNC. Go to pulse engine settings tab, and under the probing input in the lower left corner of the page, scroll down and select Pin 19. Click apply. Close and restart mach 3. When you go to diagnostics page in mach3 after it’s reopened, the digitize light indicates whether the probe circuit is closed. IF it’s lit, it’s closed. IF not, it’s not.

    If this information exists anywhere else, I couldn’t find it. I found it through working with poblocks, which also updated my pokeys57cnc firmware.

    Click the link to respond:
    how to configure the Z probe using the pokey57cnc controller

Get Help with:
This Product
Orders
Tech Support
Sales
This Product
Order Query
Tech Support
Sales
Not logged in. Log In Register
Track Order(s)
View Order(s)
I Want to Schecule a One-On-One Paid Tech Support Session
Book an Appointment Pertaining to a BuildYourCNC Product (Free)
Ask a Quesion Below (Free):
Book an Appointment Pertaining Other Equipment ($60/half hour)
Book an Immedite Appointment Pertaining Other Equipment ($120/half hour)
Ask a Quesion Below (Free):
Waiting for response... I may not answer immediately, but I was notified on my cellular phone so my response is forthcoming. If I don't respond immediately, you can always go to the [My Account] page to see all of our chats at any time.