We are working on getting these on the blackTooth page


Additional Information:
Ok, thanks. Do you use a separate 24V P/S for the supply voltage on the AWC708C or tap into the stepper motor P/S?

Click the link to add information to this solution:
Do you have instructions how to mount the AWC708 DSP on the blackTooth?

The motor that is attached to the 4th axis is wired as follows:

The motor should have red, green yellow and blue wires coming form the motor. The red and green are paired as one coil and the yellow and blue is paired as the other coil. You can wire the motor to a 3.0 amp driver with red to A+, green to A-, Yellow to B+ and Blue to B-

Click the link to add information to this solution:
HOW DO I WIRE THE 4TH AXIS THAT YOU SELL. I HAVE MACH3 SOFTWARE. NO INSTRUCTIONS ON YOUR SITE

The instructions to connect the USB CNC Interface for the blackTooth Laser Cutter and engraver can be found on instruction #18 on thispage: https://www.buildyourcnc.com/blackToothLaserCutterAndEngraver.aspx

Click the link to add information to this solution:
Are there any instructions for use the USP breakout board for a CO2 laser?

Some of our kits use video instructions to complete the assembly and those videos can be downloaded from youtube. The kits that offer illustrations and narrative associated with the illustrations are intended to be used directly from that product page. If you wish to receive printed instructions, please call us to specifically request this.

Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:
TctyH5A7

Additional Information:
-1 OR 2+544-544-1=0+0+0+1 --

Additional Information:
-1 OR 2+181-181-1=0+0+0+1

Additional Information:
-1' OR 2+544-544-1=0+0+0+1 --

Additional Information:
-1' OR 2+409-409-1=0+0+0+1 or 'YqFOAy5a'='

Additional Information:
-1" OR 2+380-380-1=0+0+0+1 --

Additional Information:
if(now()=sysdate(),sleep(15),0)

Additional Information:
0'XOR(if(now()=sysdate(),sleep(15),0))XOR'Z

Additional Information:
0"XOR(if(now()=sysdate(),sleep(15),0))XOR"Z

Additional Information:
(select(0)from(select(sleep(15)))v)/*'+(select(0)from(select(sleep(15)))v)+'"+(select(0)from(select(sleep(15)))v)+"*/

Additional Information:
-1; waitfor delay '0:0:15' --

Additional Information:
-1); waitfor delay '0:0:15' --

Additional Information:
-1)); waitfor delay '0:0:15' --

Additional Information:
1 waitfor delay '0:0:15' --

Additional Information:
xcfL6U8x'; waitfor delay '0:0:15' --

Additional Information:
rX9a3bfP'); waitfor delay '0:0:15' --

Additional Information:
evHzDfpD')); waitfor delay '0:0:15' --

Additional Information:
-5 OR 110=(SELECT 110 FROM PG_SLEEP(15))--

Additional Information:
-5) OR 585=(SELECT 585 FROM PG_SLEEP(15))--

Additional Information:
-1)) OR 963=(SELECT 963 FROM PG_SLEEP(15))--

Additional Information:
74ExMZFx' OR 396=(SELECT 396 FROM PG_SLEEP(15))--

Additional Information:
sADmKZTL') OR 910=(SELECT 910 FROM PG_SLEEP(15))--

Additional Information:
BwQqNiWP')) OR 809=(SELECT 809 FROM PG_SLEEP(15))--

Additional Information:
YQHwupOA')) OR 34=(SELECT 34 FROM PG_SLEEP(6))--

Additional Information:
vjQP3wiW')) OR 626=(SELECT 626 FROM PG_SLEEP(13))--

Additional Information:

*DBMS_PIPE.RECEIVE_MESSAGE(CHR(99)||CHR(99)||CHR(99),15)

Additional Information:

'||DBMS_PIPE.RECEIVE_MESSAGE(CHR(98)||CHR(98)||CHR(98),15)||'

Additional Information:
1'"

Additional Information:
1����%2527%2522

Additional Information:
@@qpunq

Additional Information:
@@qpunq

Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
Are the kits provided with printed instructions or a hi-res version of whats online?

You can find the wiring diagrams for the blackTooth on step 105 and 106 on the list of instructions on the blackTooth page. Step 105 pertains to the parallel breakout board and step 106 pertains to the USB interface board.

Additional Information:
wire size

Click the link to add information to this solution:
WHERE ARE THE WIRING DIAGRAMS FOR BLACKTOOTH LASER CUTTER IN INSTRUCTIONS?

To wire the CNC electronics, use the tutorial for the specific interface board you are using.

If you have the parallel breakout board, use this tutorial:
https://buildyourcnc.com/CNCElectronicsandWiring.aspx

If you have the USB interface board, use this tutorial:
https://buildyourcnc.com/tutorials/tutorial-Electronics-USB-Interface-Wiring

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
The instructions for the 3-axis combo at https://buildyourcnc.com/item/electronicsAndMotors-3axis-425-elcombo seem to be missing. Can you look into that.

You can find the wiring diagram for the Mach3 USB card on its product page here:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Here is a direct link to the diagram:
https://www.buildyourcnc.com/Documents/Electric%20Wiring%20Diagram.pdf

Click the link to add information to this solution:
I need wiring instructions for the ST- USB MOTION CARD

Are you trying to determine how to wire the switches or where to place them on the Vertical Laser XL? Let me know and I will provide some pictures or video on how to do this.

Additional Information:
Kind of both. Have somewhat of an idea as to how to wire them but you included rotary and other limit switches. Not sure which ones to put where. Never worked with these before.

Click the link to add information to this solution:
Do you have a more detailed diagram of the rotary and 15A limit switches on the vlxl?

We don't have cad models of the HIWIN blocks, but you can find the models on McMaster.com. They have can drawings and models for most of these types of parts.

Click the link to add information to this solution:
do you have CAD available for the hiwin guide blocks you sell and the rail?

There is no specific manner in connecting the water lines to the spindle. No specific output and input locations, only the diameter which we use is 1/4 Inside Diameter and 3/8 Outside Diameter (you might find another one that works just as well).
Unscrew the 2 hose nuts and feed the tube through (will be snug), and adjust the tube on the hose fittings and screw the hose nuts down. Feed the tubes through your machine towards the water bucket, making sure it will not get caught on any moving parts and cause a jam/leak, and fit one tube to the outlet of your water pump and leave the other tube to the bucket as a return line. (unless you are using a cooler like a radiator, then feed it to the outlet of the radiator and to your water pump)

Click the link to add information to this solution:
Are there any special instructions regarding connecting water lines to the 2.2k spindle?

We don't have cad models of the HIWIN blocks, but you can find the models on McMaster.com. They have can drawings and models for most of these types of parts.

Click the link to add information to this solution:
DO YOU HAVE CAD AVAILABLE FOR THE HIWIN GUIDE BLOCKS SELL AND RAIL?

We don't have cad models of the HIWIN blocks, but you can find the models on McMaster.com. They have can drawings and models for most of these types of parts.

Click the link to add information to this solution:
DO YOU HAVE CAD AVAILABLE FOR THE HIWIN GUIDE BLOCKS SELL AND RAIL?

We actually tried dissassembling one of our spindles in house with no success, but I just found a good thread on CNCZone that has a good set of photos and instructions.

Here is the link: http://www.cnczone.com/forums/spindles-vfd/129454-water-cooled-chinese-spindle-disassembly.html

Please let me know if this helps.

Additional Information:
Also, If you have no success, let us know and we will make an attempt here on video.

Click the link to add information to this solution:
Are there instructions to disassemble the 2.2KW spindle (220v)? We need to replace the bearings.

If you are looking for the drivers to pair with NEMA 34 stepper motors, you can find the 6.0 amp drivers here:
https://www.buildyourcnc.com/item/electronicsAndMotors-stepper-driver-6!0a

The other electronics to send the signals to the 6.0 amp drivers (the control board that operates with the control software) is subject to personal preference, but here they are listed:

Our breakout board (works with Mach3 and LinuxCNC and requires a parallel port on your computer):
https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay

The PoKeys57CNC (works with Mach3 and Mach4):
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Generic USB breakout board (works with Mach3):
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Additional Information:
Do I need a driver for every motor or can I use one driver for all four motors

Additional Information:
Each motor needs its own driver.

Click the link to add information to this solution:
I HAVE NEMA 34 MOTORS BUT NEED THE ELECTRICAL COMPONENTS DO YOU A KIT WITHOUT INCLUDED?

The greenBull videos are back up. The videos were blank since we added security to the website and those videos were coming from an unsecured http version of YouTube rather than their https.

Click the link to add information to this solution:
greenBull Assembly Instructions The following videos are missing: https://www.buildyourcnc.com/greenBullCNCMachineKit.aspx

The wire that we sell for the limit switch wiring is here: https://www.buildyourcnc.com/item/3d-printer-component-cnc-electronicsandmotors-cable-wire-3-conductor-22-awg-wrcon-cablewire3conductor22awg

This is shielded cable to make sure there isn't any external interference with sensitive components and long wires associated with limit switches. This is necessary due to the interference caused by the motors on a CNC router and the milling process.

Additional Information:
So unshielded is cool. That's what I was curious about. Cheers.

Additional Information:
Absolutely. It's really the only type of cable I would recommend for connecting limit switches.

Click the link to add information to this solution:
Do you sell 22 to 24 AWG stranded and shielded for wiring of the limit switches and E_Stop?

If the products have documents available, they are generally found on the product page itself, somewhere in the description or under the instructions.

Click the link to add information to this solution:
Do you have data sheets available for the Adjustable Rotary Limit Switch and E-Stop (Emergency Stop) Button - 120v-10A/240v-6A?

To connect the stepper motor drivers to the Mach3 USB interface card, you will need to follow the wiring diagram here: https://www.buildyourcnc.com/Documents/Electric%20Wiring%20Diagram.pdf
which can be found here: https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board along with all of the other manuals associated with that interface card.

Please note that the DC+ and DC- on that wiring diagram (power supply to thye stepper motor drivers) is not correct. The DC- is connected to GND on the drivers and the DC+ is connected to VCC on the drivers. Typically, the DC+ on the power supply is labeled V+ and the DC- is labeled either COM or V-.

If you are having any issues with the wiring, please let me know and I will elaborate. Thanks.

Click the link to add information to this solution:
Yawl sold me a ST-USB MOTION CARD I have surched all your electronics and can't find wring instructions I need to know where to connect X,Y and Z to this controler

Check step 9 on this page: http://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay

Click the link to add information to this solution:
IF YOU HAVE CIRCUIT (OR PICTURE) OF HOW THIS RELAY IS CONNECTED TO THE ROUTER