[ Log In ]
[ Register ]
NEW: CNC Router PLANS Available for all of our Newest CNC Models!! Click here to "Design Your CNC".

Question #: 13506

Question: Will Mach3 work on windows 8.1

Current Solution

Yes, you can use Mach3 CNC motion control software with Windows 8, but you will not be able to access the parallel port with this version of Windows and Mach3. If you wish to use Windows 8 and Mach3 together, you will need to use a USB motion controller like the one shown at the following URL:

https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Respond:

Other Possible Solutions to this Question

  • Will the mach3 usb interface card work with Windows 7?

    Yes, Mach3 (the software profram) will work with Windows 7, and windows 10 when coupled with the Mach3 USB interface. If you intend to use the parallel port driver, stick with Windows 7 in 32-bit mode.

    Click the link to respond:
    Will the mach3 usb interface card work with Windows 7?

  • will mach3 work on a cnc masters mill

    Yes, you can use the Mach3 software on a CNC Masters Mill, but you will need to replace the main controller card with one of the following:

    Our breakout board (works with Mach3 and LinuxCNC and requires a parallel port on your computer):
    https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay

    The PoKeys57CNC (works with Mach3 and Mach4):
    https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

    Generic USB breakout board (works with Mach3):
    https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

    This board will need to be connected to the drivers for each stepper motor. From my research, these mills have gecko drivers to drive the individual stepper motors.

    It has also been noted with the power supply may be under powered as well. If you feel that is the case, you may want to consider replacing that as well.

    Click the link to respond:
    will mach3 work on a cnc masters mill

  • will any of your software work with Windows 10

    Yes, all of the software we sell on this website will work on windows 10.

    Additional Information:
    I have a usb controller with JP-3163B 3.9 V is it able to work with mach 4 and windows 10

    Click the link to respond:
    will any of your software work with Windows 10

  • Is there any other software that will work with your controller Mach3?

    The mach3 control software will work with all major CAM software (CAMBAM, Aspire and Vectric, BobCAD/CAM, ArtCAM, Dolphin CAM, CAM software that integrate with SolidWorks and AutoDesk Inventor, and many more).

    Click the link to respond:
    Is there any other software that will work with your controller Mach3?

  • Will the Mach 3 USB breakout board work with a Windows 7 64 bit system?

    I don't see why Mach3 under windows 64-bit wouldn't work with an interface that uses USB as it's primary communication method. I am a bit vague on this, so I will do more research on it.

    We recommend Mach3 run under Windows 32-bit when using the parallel interface as this is a legacy function.

    Additional Information:


    Additional Information:
    mach 3 usb board setup

    Additional Information:
    I am running Mach3 under Windows 7 Pro 64bit without any problems.

    Additional Information:


    Additional Information:

    Click the link to respond:
    Will the Mach 3 USB breakout board work with a Windows 7 64 bit system?

  • Can the completely configured blueChick, with computer be shipped with working and test Unbuntu/EMC2 and not Windows/Mach3?

    I noticed in the Computer CNC Systems of this webpage that Linux/EMC2 (now called LinuxCNC) is available on the preconfigured systems. The wording on the CNC Machines page makes it look like Windows7 is all that is available. So thats the best I can see for now as far as clarity.

    Yes, if the redLeaf or redSprout is purchased with the machine, we can completely configure the electronics to use Ubuntu and Linuxcnc. If windows is selected, we install Windows 7 and completely configured under Mach3.

    If Windows is not selected, we assume Ubuntu/Linuxcnc, but we always contact the customer to confirm in these cases.

    Click the link to respond:
    Can the completely configured blueChick, with computer be shipped with working and test Unbuntu/EMC2 and not Windows/Mach3?

  • Help with loading mach3 usb interface board on Windows 10

    The Mach3 usb controller/interface has instructions and videos on this page:
    https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

    There is a 5 step process on that page to install the plug-in and the configuration xml file that is necessary for the proper functioning of the controller.

    The videos on that page also demonstrate in detail how to install the software, plug-ins, xml file and wiring and testing most of the features of the Mach3 USB interface.

    Hope this helps.

    Click the link to respond:
    Help with loading mach3 usb interface board on Windows 10

  • Help with loading mach3 usb interface board on Windows 10

    The Mach3 usb controller/interface has instructions and videos on this page:
    https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

    There is a 5 step process on that page to install the plug-in and the configuration xml file that is necessary for the proper functioning of the controller.

    The videos on that page also demonstrate in detail how to install the software, plug-ins, xml file and wiring and testing most of the features of the Mach3 USB interface.

    Hope this helps.

    Click the link to respond:
    Help with loading mach3 usb interface board on Windows 10

  • Help with loading mach3 usb interface board on Windows 10

    The Mach3 usb controller/interface has instructions and videos on this page:
    https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

    There is a 5 step process on that page to install the plug-in and the configuration xml file that is necessary for the proper functioning of the controller.

    The videos on that page also demonstrate in detail how to install the software, plug-ins, xml file and wiring and testing most of the features of the Mach3 USB interface.

    Hope this helps.

    Click the link to respond:
    Help with loading mach3 usb interface board on Windows 10

  • WILL THE USB BREAKOUT BOARD WORK WITH MACH3?

    Sure, the USB interface has a place for 4 axes of limit switches.

    Each axis can have two limit switches: one for the ++ (positive) end and one for the -- (negative) end. The positive end would be the limit switch at the end of the machine that, say the machine has a 4'x8' area, reaches a bit after the 8 foot mark. The negative end would be the limit switch behind the 0 foot location behind the origin. If the origin is in the middle, the negative would be at a little more than the -4 foot end and the positive would be at a bit more than the +4 foot end. Note that you can have more than one switch on each pin where the NC is connected in serial fashion and the NO is connected in parallel fashion (this can be seen on the diagram in the multiple limits switch section). The software configurations for the limits switches are under File -> Settings -> Limit.

    A typical limit switch has three connections on it. These connections consist of COM (common), NC (normally closed) and NO (normally open). The COM would generally go to GND and the NC or the NO would go to the pin. If the NC is used, then the the switch is constantly connected until the switch is pushed (engaged) then the connection from the pin to gnd is broken (open). Use the settings in software to set whether in NC or NO configuration.

    Let me know if this information was helpful (or not) by adding information to this question. Thanks.

    User response:
    Thank you very much for this helpful information. I'm still a little fuzzy on how the 6 limit switches physically connect to each other and to the USB breakout board. You've stated one switch (home) goes to positive and another switch (limit) goes to negative. Are all the GND prongs from all 6 switches connected to each other and going to GND on the breakout board, or no? And the NC prongs, how exactly are they connected to each other? And to the board? There has to be a diagram somewhere shows this visually, no? I don't know how to wire the switches in series or in parallel. I have already physically installed all the switches on the machine and ran the wires to where the board is. Now I just need to know where to plug these wires into the board. Also, taking into consideration that I'm using the Planet CNC software, the only settings I have pertaining to limit switches is "Enable/Disable" for each axis, and the actual limit for each axis. Nothing about NC or NO. Is that only in Mach3?
    Thank you.

    buildyourcnc response:
    On the USB interface, the COM on the switch connects to GND and the NC or NO connects to the input pin (i.e. x++, y--, etc.)

    Limit switch configuration is rather difficult to understand, especially with series and parallel. You can think of series as a single wire going from GND to the axis letter input terminal (i.e. X++ or X--). If the wire is broken, then the circuit is open (or the switch is engaged in a normally closed scenario). Normally closed is like an actual wire, and when engaged, the switch "opens" (breaks the wire). This is why we recommend in some systems that you can put many switches in series on a single pin. When one of the switches is engaged (breaking the connection) then the entire circuit of switches is broken and the machine stops.

    In a parallel scenario, the state of the circuit is always broken until the one of the switches is engaged and the circuit is then closed or connected. The topology looks like a ladder. All the switches connect to both sides of the ladder and the switches are like the runs of the ladder (the horizontal bars that the feet are placed while climbing). Imagine all of the switches broken in this scenario (normally open). It would be like the ladder could be split in two, but if one of the ladder runs (switches) is closed by engaging it, then that run would connect both sides of the ladder and the two sides of the ladder would have a connection.

    There is a diagram on the USB page of the various limit switch configurations. If you need more information (visual and/or otherwise), please let us know and we will immediately add that information to benefit everyone.

    Click the link to respond:
    WILL THE USB BREAKOUT BOARD WORK WITH MACH3?

  • Will the USB breakout board work with Mach3?

    Our newer USB board will work with Mach3 and can be found here at this URL:

    https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

    Click the link to respond:
    Will the USB breakout board work with Mach3?

  • DOES MACH3 WORK ON A MAC?

    There are several CAD/CAM programs out there for MacOS. Here is a list of a few: http://www.macuser.de/forum/f53/3d-2d-cad-395058/#post4499316
    I've also read good things about punchCAD: http://www.punchcad.com/
    Of course, there is always SketchUp if you are in a pinch. There are a few CAM plugins for SketchUp as well, but I've never used them, so I can't vouch for them.

    CAD/CAM will get you as far as designing your parts and producing the g-code, but if you also want to run the CNC machine with your Mac, you will need a piece of software similar to Mach3 or EMC to run the g-code. I haven't been able to find anything like these programs that runs on Mac, so you may have to run Mach3 or EMC in Windows using Boot Camp or a virtual machine such as VMware or Parallels.

    Personally, I would use the Mac to do all the CAD/CAM, then use a cheap PC to run the CNC machine.

    Additional Information:


    Additional Information:
    EasyDNC for OSX
    www.dnc-x.com

    Additional Information:

    Click the link to respond:
    DOES MACH3 WORK ON A MAC?

  • Does the Laser Controller work with Mach3?

    The laser Controller will not work with Mach3.

    Click the link to respond:
    Does the Laser Controller work with Mach3?

  • what ports do i connect my computer to on a redleaf system that has Windows Mach3 installed?

    The redLeaf system features an integrated CNC computer preinstalled with Windows and mach3. You should only need to connect a monitor/keyboard/mouse for functionality.

    Click the link to respond:
    what ports do i connect my computer to on a redleaf system that has Windows Mach3 installed?

  • Windows 7 is reboots after starting Mach3. Please advise. S

    Are you using the parallel port to interface with the machine? If so, Mach3 uses a driver that interacts with the parallel port and if there is a problem with your parallel port, then I suspect that your computer will reboot, from a short at that portion of the motherboard, of something to that effect.

    Additional Information:
    yes i use parallel port

    Additional Information:

    Click the link to respond:
    Windows 7 is reboots after starting Mach3. Please advise. S

  • will 220v vfd work on 110v outlet

    No, VFDs with an input voltage of 220v will only work on 220 volt mains.

    Click the link to respond:
    will 220v vfd work on 110v outlet

  • WILL THE LASER ENGRAVER WORK ON NON-ANODIZED ALUMINUM

    no, it will only work on anodized aluminum

    Click the link to respond:
    WILL THE LASER ENGRAVER WORK ON NON-ANODIZED ALUMINUM

  • I can't get the Mach3 USB interface to work

    Please follow the steps on the following webpage:

    https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

    Additional Information:
    Mach3 interface board not connected

    Additional Information:
    Mach3 interface board not connected

    Additional Information:
    Mach3 interface board not connected

    Additional Information:
    Mach3 interface board not connected

    Additional Information:
    Mach3 interface board not connected

    Additional Information:
    Mach3 interface board not connected

    Click the link to respond:
    I can't get the Mach3 USB interface to work

  • limit switch does not work as wired mach3 usb

    Are you connecting the limit switch in normally open mode? I would suggest connecting a single limit switch from the DCM terminal to one of the input terminals. Make sure you have a 24v power supply connected between the 24V terminal and the DCM terminal.

    Additional Information:
    Are you connecting the limit switch in normally open mode? I would suggest connecting a single limit switch from the DCM terminal to one of the input terminals. Make sure you have a 24v power supply connected between the 24V terminal and the DCM terminal.

    Click the link to respond:
    limit switch does not work as wired mach3 usb