Can you check if there are cracks in the inner glass tube? Also, check to see if there is water between the inner glass tube and the outer glass tube. That will give you an indication of cracking in the inner glass tube.

Click the link to add information to this solution:
I was in the process of aligning mirrors for our vertical XL and suddenly the laser does not fire anymore, there is an arcing sound and a light near the Anode (positive) connector of the tube on the very inside. Do you think the laser tube would go bad so quickly? how could we avoid this?

BYCNC Response:
This is correct. You will need to use a method appropriate for the software you are using. Also remember that NC switches are typically wired in series, while NO switches are normally wired in parallel.

User Response:
I am using the cnc planet software for your USB board. Are the limit configurations in this software?

BYCNC Response:
Yes, Planet CNC software is compatible with the use of limit switches. Configuration information will depend on your specific application. You can view Planet CNC's information here: http://www.planet-cnc.com/files/CNCUSBController.pdf

Click the link to add information to this solution:
LIMIT SWITCHES FOR AXIS. THE PRINT SHOWS THAT YOU CAN WIRE LIMITS EITHER N.O. OR N.C. SO IF THIS IS CORRECT I WOULD NEED TO TELL BOARD IN SOFTWARE HOW LOOK AT THESE LIMITS, I'M GOING GET AN INPUT LOOSE DEPEND ON IT.

The installation of the motor inside the gantry is mounted and wired before installation of the back plate of the gantry. For Example, our blackFoot machine seen in steps(124/139), you can see that the gantry and and z axis is complete finished before back plate is placed.

Click the link to add information to this solution:
Am I supposed to drill a hole in the back of the gantry to access the wires for the motor?? There does not seem to be a way to access the wires for the x axis motor once the gantry back is installed.

To wire the CNC electronics, use the tutorial for the specific interface board you are using.

If you have the parallel breakout board, use this tutorial:
https://buildyourcnc.com/CNCElectronicsandWiring.aspx

If you have the USB interface board, use this tutorial:
https://buildyourcnc.com/tutorials/tutorial-Electronics-USB-Interface-Wiring

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
The instructions for the 3-axis combo at https://buildyourcnc.com/item/electronicsAndMotors-3axis-425-elcombo seem to be missing. Can you look into that.

No, at this time, we do not offer any .dxf or any other type of file to cut the pieces for the DIY Combo #1. Just the directions that you are already able to access with the dimensions in them.

Additional Information:

Click the link to add information to this solution:
Are there .dxf files or other files for the MDF parts in Combo #1 so that they may be cut using a CNC?

We could not guarantee, nor say, whether or not your current software would be able to utilize the USB breakout board. Our USB breakout board is designed for use with Planet CNC software found here, http://www.planet-cnc.com/index.php?page=software

As far as we know, this is the only CNC Controller software that operates on a USB breakout controller.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
Is it possible to manage USB Controller (Breakout) from my own (custom) Windows application? Is there a driver API or smth for that?

Yes, it is found in laser components section

Click the link to add information to this solution:
DO YOU GUYS SELL THE POTENTIOMETER FOR YOUR LASER SYSTEM BY ITSELF

I current;y use a 2 inch focal length lens in my VLXL.

Click the link to add information to this solution:
Hello, Patrick. What focus length do you run on your VLXL? 2.5"?

The stepper motor on the X axis on the VLXL is this motor here:
https://www.buildyourcnc.com/item/electronicsAndMotors-nema34-651ozin

There is no black lead on that motor and the connection diagram can be found here:
https://www.buildyourcnc.com/Documents/PN.SM86HT80-5504B-U(inhouse%20PN.85BYGH450A-47-80)%20(1).pdf

Red - A+
Green - A-
Yellow - B+
Blue - B-

The wiring diagram on the instructions for the Vertical Laser XL is meant as a general guide for all laser systems. The motor specific to the axis should be checked against the datasheet to insure proper wiring.

The 24V power supply should be connected to the laser controller. The 36V power supply should be connected to the drivers to power the motion electronics.

Additional Information:
My fault. Must have had that backwards. I'm sure he told me the right way.

Additional Information:
Not a problem. The laser controller has two terminals labeled for the 24V connection.

The 36V power supply works really well for stepper motor drivers as the voltage/current on this power supply allows for best stepper motor performance with this laser application.

Click the link to add information to this solution:
Hello! Question about the x motor on the vlxl. There is no black lead. Is the yellow in its position? Also, I really just want to double check that this wiring diagram is solid. About to finish the wiring. Juan told me to use the 36V for the tube and 24 for the drivers. Correct?

Our 1.5/2.2kW spindle will work with both setups, in our wiring diagram it is more seen as the Euro/AUS-style, however you can do the same thing with the North American style as well. Also depending on if you have single or three phase 220V, you can use pins R, S, T. A manual will arrive in the VFD box, which will have further information and diagrams.

Please seek a certified electrician if you are unsure of any aspect in wiring the spindle or VFD, since wiring to main lines will require wiring of the plug and main lines to the inverter and to avoid any damage or injury's while installing the 1.5/2.2kW spindle and VFD combo.

Click the link to add information to this solution:
On the wiring diagrams for the 220v inverters I noticed that there is one hot (220) a neutral and a ground. Will the inverter work with the American split phase system? Hot (120) hot (120) ground?

Here is the answer to your first questions regarding the blueChick motors:
https://buildyourcnc.com/FAQ/9024

The shipping of the blueChick CNC will depend on if the machine is assembled or not. There is a duty for international orders, but I am unsure of the cost in other countries other than the US.

Thanks

Click the link to add information to this solution:
What are the specs for the stepper motors on the Bluechick? How much for shipping to Toronto, ON, Canada? Is there duty for shipping to Canada?

The files and hardware option for our machines has been removed from the site due to the following reasons:
Difficulty for the end use of the files and the challenges (and time/money) on our side to assist in using these files.
The abuse of these files over the internet.
Ultimately may reduce the sales of machines keeping us in business.
Sadly, this is what has come out of our company attempting to be open; however, the machines sold on this site is still far lower in price than the competition for the quality that we provide as we have a great desire to engender the cottage industry to fulfill their need for low end manufacturing. My sincere apologies if this causes any inconvenience.

Additional Information:
NO, is not possible, I can help with the shipping cost

Additional Information:

Click the link to add information to this solution:
BlackToe g-code or rather the DXF-file(s), but I can't find that option on the site anymore. Also, is it possible to convert all measurements to mm instead of inches? (Since I live in Sweden). Thank you!

Sure, let me check.

Additional Information:
Your order was shipped out on Tuesday (10/20/2020). I noticed that your email was not stored in the customer record when the order was made. I will send you the tracking number via email now.

Click the link to add information to this solution:
Placed an order for the cable set for the Pokeys57cnc interface on 10/20 but it is not showing up in My Account as being ordered. It was charged to my credit card and I have not had any info that it was received by you.

Physical size of the subject affects the fraction of the total radiofrequency energy that is absorbed in the body. To account for this known effect, the maximum permissible exposure standards for radiofrequency energy were set for the worst-case condition, that is assuming the body size for maximal absorption at a given frequency. Thus the maximum permissible exposure standards are fully protective for bodies of different sizes. For more detailed information, see the answers and the cited references to questions 79, 109, 694, and 893 under the Nonionizing Radiation section of the Health Physics Society Ask The Expert Web page. Gary H. Zeman, ScD, CHP

Click the link to add information to this solution:
WHAT EFFECTS OF CELL PHONES WILL THERE BE ON YOUNGER PEOPLE OPPOSED TO OLDER PEOPLE? THE AGE OR STATE DEVELOPMENT EFFECT DANGERS A PHONE?

Did you connect the USB connector to the breakout board?

Additional Information:
YES I CONNECTED THE USB TO THE BREAKOUT BOARD

Click the link to add information to this solution:
I connected the electronics (for 2 x 4 feet) that I ordered from you. But how do I check if I connected all the wiring properly. There is neither any light on motor drivers nor on breakout board. And the motor shaft also does not move before and after the power supply is given.

Are you able to install a newer version of Mach3? If you are worried that your configuration will be lost, you can save the configuration by copying all of the XML files from the Mach folder. The XML files contain all of the settings that you applied in Mach3. Just in case the XML files are not compatible with the new version, make sure not to erase the current Mach3 that you have on the machine.

Click the link to add information to this solution:
[575] Hi, I have an old version of MACH3 V1.84 - Can someone tell me where to place the USB motion drive as there is no plugin folder in this version.

Can you provide the model number of your VFD?

Yes, I have the "YL600 - 2S - 2K20"

It just came with a small booklet that is all in Chinese...

Click the link to add information to this solution:
I WIRED MY VFD (2.2KW VERSION) AND TRIED TEST RUNNING THE SPINDLE. CONFIGURED TO YOUR SPECS ON THIS WEBSITE, ONLY ISSUE IS WE GOT AN ERROR CODE. ERR 02, DO YOU KNOW WHAT IS? OR HAVE A LIST OF CODES? THANK

There are a number of opportunistic gadgets on the market to allegedly protect the user from hazards of cellular phones. You can search the Internet to find the latest, ranging from antenna shields to whole-body shielding materials. Most experts believe that these devices take advantage of customers' misunderstanding and unfounded fears to sell products with no real value. First of all, cell phones that operate within the guidelines established by national and international safety panels have never been shown to pose a health risk to the user (see answers to other questions on cell phone safety on this website). Secondly, placing any kind of shield over the antenna of a cell phone will in most cases cause it to increase its RF output as it attempts to compensate for signal loss in the shield and maintain a quality phone call. The U.S. Food and Drug Administration published an advisory on cell phones several years ago that said if you are concerned about risks of using a cell phone, then simply use it less. That is still good advice today. Gary Zeman, ScD, CHP Lawrence Berkeley National Laboratory

Additional Information:



Additional Information:

Click the link to add information to this solution:
ARE THERE PRODUCTS AVAILABLE TO THE GENERAL PUBLIC THAT CAN BE PURCHASED PROTECT CELLULAR OR PORTABLE TELEPHONE USERS FROM RADIATION? IF SO, WHERE THESE FOUND?

We are currently working on a relay board that will connect to USB breakout board, and the router/spindle for both the on/off function. Unfortunately we still do not have it completed or ready to be placed on our website, but it is in the final stages of testing. Please check back regularly for updated stock!

Here is a link to a tutorial for a DIY relay circuit:

Click the link to add information to this solution:
I AM PUTTING TOGETHER THE BLACKFOOT AND USING A PORTER CABLE ROUTER. CONFUSED ON HOW TO RELAY ROUTETR WITH USB BOARD. IS THERE ANOTHER SWITCH THAT GOES BETWEEN BOARD ROUTER SO PLANET CNC CAN TURN PERHAPS VACUUM OFF?