The 2.2kW spindle will have the same amount of torque and strength using either the 110V or the 220V inverter. Nothing will significantly change in either application since the 110V inverter has a small step up transformer which will increase the voltage from 110V to 220V to run the spindle efficiently.

Additional Information:
I'd like confirmation on this -- isn't there a cost in efficiency to having the 110v step up to 220v?

Additional Information:
Thank you so very much for explaining this!!! I truly appreciate your help! Tricia

Additional Information:
Thank you so very much for explaining this!!! I truly appreciate your help! Tricia

Additional Information:
Thank you so very much for explaining this!!! I truly appreciate your help! Tricia

Additional Information:
Thank you so very much for explaining this!!! I truly appreciate your help! Tricia

Additional Information:
Thank you so very much for explaining this!!! I truly appreciate your help! Tricia

Click the link to add information to this solution:
Good morning, I would like to know if the strength of the 2.2kw spindle is weaker when using the 110V version of the VFD. Does it have the same power as the 220V version VFD?

The dimensions for the #40 drive sprockets will be 1.835" radius tooth to tooth , .575" from teeth to teeth, 0.600" / 3/5 ID, 1.249" OD.
Now the idler sprocket dimensions (same format):
Radius ttt: 2.963"
Fttt: 0.535"
ID: 0.600" / 3/5
OD: 0.825"

Click the link to add information to this solution:
I am designing/building a cnc plasma cutter and I would like some info on some of your parts. Would it be possible to get dimension and/or drawings (or models) of the #40 drive and idle sprockets?

If you are located near Houston, Texas area you can stop by our shop. If you are not near us, you can check in our forums, and see if you can find someone in your area that has one of our machines, and would be willing to let you come see it in action.

Click the link to add information to this solution:
I WOULD LIKE TO KNOW IF THERE IS A STORE OR SHOP WHERE CAN SEE THE PRODUCT AND BUY IT?

Our spindle should work fine with your Delta VFD-M 220v. Spindles that match a VFD are specific to the coil windings. The bearings, shaft and other mechanical components that make up the spindle may be different, but that should not matter.

Click the link to add information to this solution:
I have a GMT 2.2kw water cooled spindle that sounds like the bearings are going out and want to know if your spindle (https://buildyourcnc.com/Item/spindle-inverter-2!2kw-spindle-novfd) is comparable for a swap. The drive is a Delta VFD-M 220v.

The rods where the drive sprockets are located (typically the X-axis) are not flat enough, so that the set screws hold the rod securely. Taking a file tool to make the surface where the set screws can hold the rod in place a bit flatter.
On the Y-axis, make sure you have the idler sprocket in the correct place being dual nuts on top corner (away from the motor (http://buildyourcnc.com/Item/cnc-machine-bluechick-v4#prettyPhoto/1/) and (https://www.buildyourcnc.com/images/bluechick%204-3%20instructions%2013_700_sm.jpg)) to have the sprockets line up perfectly.

The #40 drive sprocket will not work with the #25 chain sent with the kit.

Click the link to add information to this solution:
blueChick v4.2. The #25 drive sprockets occasionally come loose especially on the y-axis. The screws are barely on the shaft when I line up the sprocket to the idler gears. Lots of Loctite or should I try the #40 drive sprocket?

Currently we do not have that modification kit, our set up is fixed for our greenBull only modification kit we have for this model is the long z-axis kit(Designed for Foam cutting).

Click the link to add information to this solution:
I am building your "Green Bull' 6 foot wide kit and I am at the stage of attaching the motor and drive chain. I would like to know if you have an modification kit available to put the 1/2" ACME screw on the Y-axis?

According to the supplier of the 2.2 kW spindle, the safest operating speed for the spindle is 6000 RPM. The supplier also stated that theoretically, the spindle can operate from 0 to 24,000 RPM. I am continuing a dialog with the supplier to delve deeper into understanding the configurations and ramifications of such configurations for operations outside of the safe boundaries into the "theoretical" ranges.

Additional Information:
20

Click the link to add information to this solution:
I would like to know what the lowest rpm that can be acheived with the 2.2kw spindle and inverter and still have enough torque to drill

SketchUcam will output gcode which standard CNC control software will typically interpret, execute and control CNC machines. So, there is no problem using SketchUcam. However, our CNC machine control software that use our CNC machine interface boards require Windows OS, of Linux. The Mach3 USB board will only run with Mach3 control software which runs under the Windows OS. The parallel breakout board can run under Windows or Linux OS and the computer must contain a parallel port.

Click the link to add information to this solution:
I would like to know if your breakout board and driver boards are compatible with MAC OS X working with Sketch Up pro using SketchUcam ?

Yes, our porter cable collets and nuts will fit the porter cable 7518.

Additional Information:

Click the link to add information to this solution:
HAVE PORTER CABLE 7518 ROUTER ON MY CNC AND WOULD LIKE TO KNOW IF YOUR ER20 COLLET NUT, FOR THE CABLE, WILL FIT ROUTER.

You will definitely want to adjust your debounce setting in mach3 if your emergency or limit switch is engaging.

Additional Information:
Did you ever fix this issue? I am having the same problem.

Additional Information:
Did you ever fix this issue? I am having the same problem.

Additional Information:
Did you ever fix this issue? I am having the same problem.

Additional Information:
Did you ever fix this issue? I am having the same problem.

Additional Information:
Did you ever fix this issue? I am having the same problem.

Additional Information:
Did you ever fix this issue? I am having the same problem.

Additional Information:
Did you ever fix this issue? I am having the same problem.

Additional Information:
Did you ever fix this issue? I am having the same problem.

Additional Information:
Did you try changing the denounce setting?

Additional Information:
Meant to say denounce.

Click the link to add information to this solution:
When I start my spindle I get a emergency stop in Mach 3. I have run shielded cable and it is grounded at the VFD it is wired per you site instructions. any idea what to check

Dealing with our USB BoB, the potentiometer that will be used in the key jog, is a 5V, 5k - 10k Ohm potentiometer.

Click the link to add information to this solution:
I am building a cnc mill using your USB controller and i would like to know what is the specification of potentiometer used for adjusting manual axis jog speed

See the question on our "Ask the Expert" question-and-answer list on cellular towers under nonionizing radiation for a discussion of RF safety issues associated with cellular radios. The technology underlying cellular radios and base station antennas is similar around the world, but there are differences in systems design and RF safety limits in different countries. For a summary of cellular radio RF safety issues with attention to international differences see the excellent Web page, Cellular Phone Antennas (Base Stations) and Human Health, by John E. Molder, Ph.D., from the Medical College of Wisconsin. Gary H. Zeman Sc.D., CHP

Click the link to add information to this solution:
I LIVE IN ITALY AND WISH TO KNOW MORE ABOUT RADIATIONS CAUSED FROM MOBILE TELEPHONES. TELECOM WOULD LIKE PLACE A WIRE-ANTENNA THE HEARTH OF MY TOWN, I'M AFRAID IT. WHICH KIND RISK HEALTH COULD IT CAUSE? THANK YOU IF WILL SEND ME SOME INFORMATION SCIENTIFIC ARTICLES THIS PROBLEM!

What controller are you using to control the cnc machine (Mach3 usb, parallel breakout board, etc.)?

The spindle VFD has an input for 0-10 volts to control the speed and can be used with the MAch3 USB or the Pokeys57CNC board. There are also other terminals in the VFD to control the forwared/reverse and start and stop. Mach3 has parameters to control these output and you need to specify which pins are used for these.

You can also use the TX/RX RS-485 connection on the VFD to have total control using an FTDI USB to serial connector board to connect the computer directly to the VFD.

How to connect the USB to Serial adapter to the VFD:
https://www.buildyourcnc.com/FAQ/13790

FTDI USB to Serial:
https://www.buildyourcnc.com/item/Interfaces-newbiehack-Interfaces-TTL232R-USB-UART-Serial

Pokeys57CNC board:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Mach3 USB board:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Parallel Breakout board:
https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay



Additional Information:
I do apologize for leaving out the parts list.
Leadshine MX4660 4-Axis Digital Stepper Motor Driver
Ethernet SmoothStepper
YL600-2S-2K20 VFD
4 Relay control board
Has anyone had any success getting Mach3 to control the spindle speed and direction?

Click the link to add information to this solution:
I have the 2.2KW VFD. I would like to have it controlled through software. What are the Mode parameters that need to be changed that will allow FWD/ REV, START/STOP and RPM control?

If you were logged in when you made the purchase, you can click the "My Account" link at the top of any page on this website and see all of your orders, order line items (with direct links to these items), and shipment information.

Here is a link to the "My Account" page for your convenience:
https://www.buildyourcnc.com/CustomerInfo.aspx

I did not see your username on your internal customer record, so I added this username and you should be able to see the information in the "My Account" page.

Additional Information:
I just tested your accounts page and the cable carrier links are in there. Thanks and please let me know if you need further assistance.

Click the link to add information to this solution:
I have purchased cable carrier chain and would like to know if you could send me a copy of that order as I need to purchase extra lengths of the links I bought. Thanks

Our spindles have a runout of less than .0001 in, which includes that collets that we sell. If you use a collet from another manufacturer, we cannot guarantee this TIR (Total Indicated Runout) dimension.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
Hi, I'm interested in the 1.5 kW (kilowatt) Water Cooled Spindle with Inverter (VFD), I would like to know about the run out of this spindle?

You can always come to our offices in Katy TX. If that is not an option, we can do cut in our shop and record video for you. Specify what you would like to cut and we can consider doing this for you.

Thanks. I've reviewed the gallery and think my question comes down to this- Can I do hardwood carving like Mike M.'s guitar display cases and cut 3/4 inch baltic birch plywood with the same machine?

Absolutely, the cutting and machining is more a function of how the machining operations are created and specified. Baltic birch is not a tough material and you will be able to cut very aggressively with any of our machine kits.

Click the link to add information to this solution:
Where is the best place to see projects made with BuildYourCNC CNCs? I would like to get an idea of carving capabilities and cutting Baltic Birch plywood. Thanks.

We only have these models in SketchUp. Is that a format that will be acceptable?

Additional Information:
Anything with basic profile dimensions will work just fine.

Click the link to add information to this solution:
Would you be able to supply solidworks files for the laser nozzle, mirror mounts, & laser tube? I plan to build a laser engraver and would like to model everything up before i start building to make sure it all fits.

If you purchased the ArtCAM from us, please send an email to us at customerservice@buildyourcnc.com with the name used with making the order and we will contact the developer to send you the license.

Click the link to add information to this solution:
i have Artcam 2013 for an General Inc. Icarver 40913. My computer crash with the Licenses from Delcam i would like to know how to get the licenses.

You can find the cost of shipping and the delivery times by going to the cart (with the items you intend to purchase) and press calculate shipping. This will give you a list of carriers and their expected delivery times.

If you are purchasing a machine kit or assembled machine, it will take between 2 to 5 weeks. Kits typically take 2 weeks before shipping and assembled machines typically take 5 or more weeks depending on how many machines we are assembling at the moment.

Click the link to add information to this solution:
I would like to ask how long does it take to deliver an item to Egypt? and which shipping company will deliver the item me? and if possible, i'd like to know the total cost of the item and the shipping . . many regards