[ Log In ]
[ Register ]
NEW: CNC Router PLANS Available for all of our Newest CNC Models!! Click here to "Design Your CNC".

Question #: 14090

Question: witch city are you in

Current Solution

We are located in Katy Texas which is near Houston.

Respond:

Other Possible Solutions to this Question

  • What city are you in?

    We are currently located in Houston Texas.

    Click the link to respond:
    What city are you in?

  • How long are the wires on the proximity switches you over

    The NPN proximity switches we stock have 43" (1.09 meters) of cable and the PNP proximity switches we carry have 48" (1.21 meters) of cable.

    Click the link to respond:
    How long are the wires on the proximity switches you over

  • MY LIMIT SWITCHES ARE TRIGGERING AT RANDOM.

    Are you using shielded wire? If so, take the shield to ground. If there are any other wires in the cable that is not being used, ground those as well. The customer can also try moving the cables as far away as possible from the motor wires and motors.

    Additional Information:

    Click the link to respond:
    MY LIMIT SWITCHES ARE TRIGGERING AT RANDOM.

  • What are the dipswitch settings for the drivers?

    blueChick:

    X-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    blackToe:

    X-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    blackFoot:

    X-axis
    “CW8060 (6.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100 (“0”=down, “1”=up)
    Mach3 Motor Tuning: 914.29 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    greenBull:

    X-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/16 Microstep
    Dipswitches: 01100110 (“0”=down, “1”=up)
    Mach3 Motor Tuning: 914.29 steps/in

    Y-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/16 Microstep
    Dipswitches: 01100110
    Mach3 Motor Tuning: 914.29 steps/in

    Z-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/4 Microstep
    Dipswitches: 01100100
    Mach3 Motor Tuning: 1600 steps/in


    Scratch-Build / Book-Build Kit:

    X-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100 (“0”=down, “1”=up)
    Mach3 Motor Tuning: 1600 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    Additional Information:


    Additional Information:
    Scratch built/book CNC with NEMA 34 motors and CW8060 microstep driver

    Additional Information:

    Click the link to respond:
    What are the dipswitch settings for the drivers?

  • Are there any videos detailing wiring of limit switches and stop button?

    This video may serve helpful on the homing and limit switches:
    https://www.buildyourcnc.com/PrimeronHomingandLimitSwitches.aspx

    I don't go into great detail on the wiring, however. If after you watch that video and you still need a video, please let me know and I will make a video on the wiring of limit switches and the E-stop button.

    Click the link to respond:
    Are there any videos detailing wiring of limit switches and stop button?

  • stepper switch settings

    On the top of the stepper motor drivers is a grid with the appropriate toggle switch positions for the lead screw being used. If it is 2 turns per inch, the proper toggle switch positions would be 01101110. Try this and see if it works.

    Click the link to respond:
    stepper switch settings

  • What are the tolerances of your machines?

    The tolerance of our machines, like any machine, depends on several variables. The major variables include the manufacturing tolerance, the type of machine control used, the precision of assembly, the thoroughness of maintenance, and the initial and ongoing calibration of the machine. Because we sell kits only most of these variables are outside our control. Therefore, we are hesitant to guarantee a certain level of tolerance for an end user. However, in our experience, tolerances of .001" are readily achievable with our machines.

    Additional Information:
    What is the likely tolerance one could achieve without continual frustration and months of tinkering?

    Additional Information:
    We actually do very little tinkering with our production machine. The wood has a very small coefficient of linear expansion as compared to metals and plastic, so calibration is reduced to a very infrequent state.

    As with all machines, the determination of backlash in all parts of the machine is important, managing the tightening of these points of adjustment is necessary, but are still done infrequently.

    Click the link to respond:
    What are the tolerances of your machines?

  • Do you have wood holders for switching my Black Toe from router to spindle?

    You will need a Z-axis mount for Spindle if you are currently using a router.

    Click the link to respond:
    Do you have wood holders for switching my Black Toe from router to spindle?

  • What are the toggle switch settings on the stepper motor drivers for the .5 in. lead screw 10 tpi 2 turns per inch? Thankyou!

    On the top of the stepper motor drivers is a grid with the appropriate toggle switch positions for the lead screw being used. If it is 2 turns per inch, the proper toggle switch positions would be 01101110. Try this and see if it works.

    Click the link to respond:
    What are the toggle switch settings on the stepper motor drivers for the .5 in. lead screw 10 tpi 2 turns per inch? Thankyou!

  • Were are the mounting locattions of the 6 Limit switches on the Blackfoot 4.3

    Here are the recommended locations for limit switches for our CNC machine kits.

    The x-axis limit switches should be located on a single gantry. This makes the wiring of the limit switches close in proximity and more manageable.
    https://www.buildyourcnc.com/images/IMG_6367-800.JPG

    The y-axis limit switches should be located at each end of the gantry. This keeps the switches stationary and impose minimal movement of the wire for better wire management.

    One end of he gantry:
    https://www.buildyourcnc.com/images/IMG_6361-800.JPG

    Other end of the gantry:
    https://www.buildyourcnc.com/images/IMG_6360-800.JPG

    Click the link to respond:
    Were are the mounting locattions of the 6 Limit switches on the Blackfoot 4.3

  • Can you tell me what gauge wire is needed for limits switches and the spindle?

    The hookup wires you will need is 22 to 24 AWG stranded and shielded for the wiring of the limit switches and E_Stop. Our kit customers select various places for these switches, so we don't supply the wiring. If you don't use shielded cable, you will need to change the debounce setting in Mach3 (if that is the control program you are using).

    We typically use 14 AWG stranded wire for the VFD to Spindle (U, V, W) connections.

    Click the link to respond:
    Can you tell me what gauge wire is needed for limits switches and the spindle?

  • Are the prices on your website in US dollars?

    Yes, all prices on the website are in US Dollars.

    Click the link to respond:
    Are the prices on your website in US dollars?

  • will any of your software work with Windows 10

    Yes, all of the software we sell on this website will work on windows 10.

    Additional Information:
    I have a usb controller with JP-3163B 3.9 V is it able to work with mach 4 and windows 10

    Click the link to respond:
    will any of your software work with Windows 10

  • hi how are do you build tshirts printing machine

    The dimensions of the optional table are 73" x 34".

    Click the link to respond:
    hi how are do you build tshirts printing machine

  • What version of LaserCAD are you supporting now?

    At this time 1/10/2020, we support version 8.10.21. As new versions of LaserCAD are available, we will support the current version.

    Click the link to respond:
    What version of LaserCAD are you supporting now?

  • There are no limit switches in my Greenbull 5x10 kit. Are these no longer needed?

    You most definitely should have received limit switches in your package. We will send you the missing limit switches.

    But to directly answer your question; no, limit switches are not needed with CNC machines. You can set up soft limits to make sure the machine does not go out of bounds.

    With that said, if the motors stall for some reason and the computer does not know the actual position of the gantry or the spindle, then the machine may actually go out of bounds and the machine may hit a physical limit. With or without limit switches, the machine will stop.

    Additional Information:
    Please call the office so that we know who you are and we can send the limit switches to the correct person.

    Click the link to respond:
    There are no limit switches in my Greenbull 5x10 kit. Are these no longer needed?

  • What are your terms and conditions for financing?

    We work with banks who will process financing requests. For more information about submitting an application for financing please contact sales@buildyourcnc.com

    Click the link to respond:
    What are your terms and conditions for financing?

  • limit switch triggered in mach3

    http://buildyourcnc.com/PrimeronHomingandLimitSwitches.aspx
    There is a pin setting in Mach3 that says how to react to the inputs from the switches. Your setting is probably wrong as the trigger happens immediately.

    You may want to think about shielded wire and/or a resistor on each limit switch line. If there are stray wires, connect them to ground. Additionally, the shield from the shielded cable insulation should alse connected to ground at both ends.
    Try upping the Debounce interval in Mach3. You have to adjust the debounce interval. You go to config,general config, and it is in the top right corner. I set mine to 100 and it seems to work well.

    Additional Information:
    how to solution cnc revo 540 limit tripped error?


    Additional Information:


    Additional Information:

    Click the link to respond:
    limit switch triggered in mach3

  • Where are the limit switch connections made when the switches are in series, and NC??

    One end of the limit switch circuit will be connected to the pin and NC, and the other end will be connected to COM and GND.

    For example: (the "-" is wire.)

    [Breakout board input pin] ---- ([NC on switch] [com on switch]) ---- [NC on switch] [com on switch] ---- [back to GND on the breakout board]

    An explanation of the limit switch connections is located on the brakout board datasheet: https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay (instruction step # 1.

    Click the link to respond:
    Where are the limit switch connections made when the switches are in series, and NC??

Get Help with:
This Product
Orders
Tech Support
Sales
This Product
Order Query
Tech Support
Sales
Not logged in. Log In Register
Track Order(s)
View Order(s)
I Want to Schecule a One-On-One Paid Tech Support Session
Book an Appointment Pertaining to a BuildYourCNC Product (Free)
Ask a Quesion Below (Free):
Book an Appointment Pertaining Other Equipment ($60/half hour)
Book an Immedite Appointment Pertaining Other Equipment ($120/half hour)
Ask a Quesion Below (Free):
Waiting for response... I may not answer immediately, but I was notified on my cellular phone so my response is forthcoming. If I don't respond immediately, you can always go to the [My Account] page to see all of our chats at any time.