Consider the loads on each axis when choosing appropriate stepper motors. If your holding torque is maxed out at roughly 16oz/in (1lb/in), then you could use the NEMA 11 or 14. Also consider the shaft sizes and current ratings when choosing drivers that pair with the motors.

Click the link to add information to this solution:
I am planning to build a scratch CNC machine to do rotary engraving on writing pens. Can you recommend the parts I would need? I'm thinking NEMA 14 (11?) and 3/8" acme rod. Not sure which linear motion to use. I have an old lathe to use for the 4th axis.

Only our greenBull CNC machines will be able to use the long Z-axis, due to structural construction of the greenBull over the blackFoot.
The height from the table top to the bottom of the gantry is: 4.25"

Both the maximum cutting height and diameter, will be dependent on the specific end mill/router bit you plan on using, since they can vary in length.
The maximum cutting height (useful to engrave or cut material)is: with spoil-board 3.875", without a spoil-board is 4.625"
The maximum diameter will (estimated) is: 3"

Specifically dealing with our greenBull long Z-axis CNC machines, depending on how you specifically design the table you can have more cutting height and a larger diameter clearance. If you only create a frame for the machine with a hollow center(adjustable midsection), allowing you to have a greater clearance.
Similar table image here: (https://buildyourcnc.com/Item/cnc-machine-greenBull-v4-6X#prettyPhoto/5/)

Click the link to add information to this solution:
Planning to Buy Greenbull or Blackfoot 4'x 8' Long "Z" Axis. My questions are: what is the hight between the table and the Gantry ? what maximun Z can useful engraving? if I instal a rotating 4 Axle. what maximun diameter can be useful.

We currently do not have any Nema motor's with a .375"/3/8" shaft diameter. The motors in stock 100 oz, 425 oz, with a 1/4" input shaft. Our 651 oz, with a 1/2" input shaft.

Click the link to add information to this solution:
Your combo kits don't specify whether they are standard NEMA motors. I need Nema 34 with a .375 shaft diameter. Which 3 axis kit work for these requirements?

To select a 4 axis NEMA 17 motor and driver combination, you will need the following:

- Four (4) NEMA 17 motors: https://buildyourcnc.com/item/electronicsAndMotors-nema17-62ozin-NEWBIEHACK-motors-stepping_motor-62_ozin

- Four (4) drivers, either the 2.5A: https://buildyourcnc.com/item/motion%20electronics-steppermotordriver-newbiehack-Motor_Drivers-2!5_Amp_modular or the 3.0A: https://buildyourcnc.com/item/electronicsAndMotors-stepper-driver-3!0a

- One (1) Power supply, either the 24V or 36V (recommended): https://buildyourcnc.com/item/electronicsAndMotors-power-supply

- Finally, an interface is needed, either parallel, or USB. The USB works with planet-cnc software only. The parallel interface works with all major CNC control software: https://buildyourcnc.com/category/breakout

Click the link to add information to this solution:
Can you supply a quote for a 4 axis combo kit with NEMA 17 Motors

The new Vertical Laser XL version 2 is available now. The price is the same as version 1, so you can simply go to that webpage and order it. The new version will automatically be sent.

https://buildyourcnc.com/item/cnc-machine-vertical-laser-xl

Click the link to add information to this solution:
When will your new Vertical Laser XL that uses the new linear rail be available?

Gcode or digital files are not available for our machines.

Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
I have the build your own CNC kit 3 Axis CNC Machine 2008, were can I get the Gcode or vector files for it ? I wanted to have it laser cut

If you go to our R&D section, you can vote for your machine and/or type a special request to create a machine that you might need.

R&D:https://www.buildyourcnc.com/ResDev.aspx

Click the link to add information to this solution:
interest i nbuilding a 2X2' low budget 4-5 axes machine of 1-2 hp with tilting, rotating spindle up to 45 degrees off vertical

The torque curve for the 651 oz-in stepping motor can be found here:

https://www.buildyourcnc.com/item/electronicsAndMotors-nema34-651ozin#prettyPhoto

Click the link to add information to this solution:
Using your NEMA 24 stepping motor with microstepping, can I get a speed range from 3 RPM to 600 RPM ?

Same issue here -- TTL output from the AWC708C never seems to be pulled low. Still troubleshooting.

Click the link to add information to this solution:
MY LASER MACHINE VERTICAL DOES NOT ACTIVATE THE LASER TUBE, VERIFY THE POWER SUPPLIES AND THEY ARE WORKING WHICH THE PROBLEM CAN BE

If your motors are hot to the touch, this is normal. Current is being drawn by the motor coils as the motor moves and as the motor stays at a position. If the motor is not using the current in the coils to move (holding it's position), the energy will be translated as heat (rather than motion, sound or light). Even while moving, some of the energy will be lost as heat. Remember that energy cannot be created nor destroyed.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
Are the stepper motors on x and y axis suppose to be hot after running for approximately 30 min. I can touch them but they are hot.

If your axis shutters and will not move unless moved by another force, that sounds like your acceleration is set too high. Lower the acceleration until it works well, then lower it a bit more to have a margin of safety.

Users response:
I've lowered my acceleration to 1 in the StepCon program and it still shutters when I jog it, anything else I could check?

Buildyourcnc response:
IF that didn't work, try swapping the X and Y drivers. That way you will pinpoint if the issue is the driver. If the proplem persists, then there may be an issue with the motor itself.

Buildyourcnc response:
The X and Y drivers can be easily swapped by swapping only the motor wires.

- Remove the x-axis motor wires from the X driver.
- Remove the Y motor wires from the Y driver.
- Insert the X motor wires into the Y driver.
- Insert the Y motor wires into the X driver.

Buildyourcnc response:
Now the Y-axis will move the gantry. Test the Gantry movement by moving the Y axis using the up and down arrow keys (mach3).

Users response:
Problem is now solved, I switched the X and Y at the redFly and got the same problem, so then I undid the wires going to each motor and switched them there and it I had a bad solder point in the X axis connector, thank you for the help

Buildyourcnc response:
You're very welcome. We will make sure to thoroughly check the solder points on the cable connectors prior to a redFly delivery.

Click the link to add information to this solution:
GreenBull 5x10 X axis shutters and spins out with acceleration at 1 in StepCon, is there anything else I can check?

Yes, with caveats. This kit includes a controller that will not be compatible, but if you use another type of controller that has web based control, you can use these electronics. Here is a list of web based control for CNC:

- Easel: The web-based software from Inventables can be accessed through Safari or other macOS-compatible web browsers.

- bCNC: A Python-based GRBL CNC command sender, although you may need to jump through some hoops to get it to run on macOS.

- Universal Gcode Sender: A Java-based software that should run on macOS if you have the Java Runtime Environment installed.

- CNCjs: Another web-based interface that you can run on macOS using Node.js.

Click the link to add information to this solution:
[50] Is there a software control package that will work with Axis Electronics Combo (For Heavy Gantry) for apple os.

Yes Mach3 is a great program. Our 3 axis is 6'X12'X3'using all BYCNC components (incl. redsprout)

Click the link to add information to this solution:
I JUST BOUGHT THE 3 AXIS W/HEAVY GANTRY, WILL MACH 4 RUN WELL WITH THIS, AND HOW LARGE CAN GO CUT AREA

Sure, the USB interface has a place for 4 axes of limit switches.

Each axis can have two limit switches: one for the ++ (positive) end and one for the -- (negative) end. The positive end would be the limit switch at the end of the machine that, say the machine has a 4'x8' area, reaches a bit after the 8 foot mark. The negative end would be the limit switch behind the 0 foot location behind the origin. If the origin is in the middle, the negative would be at a little more than the -4 foot end and the positive would be at a bit more than the +4 foot end. Note that you can have more than one switch on each pin where the NC is connected in serial fashion and the NO is connected in parallel fashion (this can be seen on the diagram in the multiple limits switch section). The software configurations for the limits switches are under File -> Settings -> Limit.

A typical limit switch has three connections on it. These connections consist of COM (common), NC (normally closed) and NO (normally open). The COM would generally go to GND and the NC or the NO would go to the pin. If the NC is used, then the the switch is constantly connected until the switch is pushed (engaged) then the connection from the pin to gnd is broken (open). Use the settings in software to set whether in NC or NO configuration.

Let me know if this information was helpful (or not) by adding information to this question. Thanks.

User response:
Thank you very much for this helpful information. I'm still a little fuzzy on how the 6 limit switches physically connect to each other and to the USB breakout board. You've stated one switch (home) goes to positive and another switch (limit) goes to negative. Are all the GND prongs from all 6 switches connected to each other and going to GND on the breakout board, or no? And the NC prongs, how exactly are they connected to each other? And to the board? There has to be a diagram somewhere shows this visually, no? I don't know how to wire the switches in series or in parallel. I have already physically installed all the switches on the machine and ran the wires to where the board is. Now I just need to know where to plug these wires into the board. Also, taking into consideration that I'm using the Planet CNC software, the only settings I have pertaining to limit switches is "Enable/Disable" for each axis, and the actual limit for each axis. Nothing about NC or NO. Is that only in Mach3?
Thank you.

buildyourcnc response:
On the USB interface, the COM on the switch connects to GND and the NC or NO connects to the input pin (i.e. x++, y--, etc.)

Limit switch configuration is rather difficult to understand, especially with series and parallel. You can think of series as a single wire going from GND to the axis letter input terminal (i.e. X++ or X--). If the wire is broken, then the circuit is open (or the switch is engaged in a normally closed scenario). Normally closed is like an actual wire, and when engaged, the switch "opens" (breaks the wire). This is why we recommend in some systems that you can put many switches in series on a single pin. When one of the switches is engaged (breaking the connection) then the entire circuit of switches is broken and the machine stops.

In a parallel scenario, the state of the circuit is always broken until the one of the switches is engaged and the circuit is then closed or connected. The topology looks like a ladder. All the switches connect to both sides of the ladder and the switches are like the runs of the ladder (the horizontal bars that the feet are placed while climbing). Imagine all of the switches broken in this scenario (normally open). It would be like the ladder could be split in two, but if one of the ladder runs (switches) is closed by engaging it, then that run would connect both sides of the ladder and the two sides of the ladder would have a connection.

There is a diagram on the USB page of the various limit switch configurations. If you need more information (visual and/or otherwise), please let us know and we will immediately add that information to benefit everyone.

Click the link to add information to this solution:
How can I convert from Xylotex to yours, four axis with limit switches. Have parallel PC and steppers on machine.

The motor that is attached to the 4th axis is wired as follows:

The motor should have red, green yellow and blue wires coming form the motor. The red and green are paired as one coil and the yellow and blue is paired as the other coil. You can wire the motor to a 3.0 amp driver with red to A+, green to A-, Yellow to B+ and Blue to B-

Click the link to add information to this solution:
HOW DO I WIRE THE 4TH AXIS THAT YOU SELL. I HAVE MACH3 SOFTWARE. NO INSTRUCTIONS ON YOUR SITE

Depending if the spindle can work with this specific VFD, it might be possible. However we would not like to risk you working unit, with a possible match so we would like more details on your specific model and any information available on the spindle itself.

Response
The only info on the spindle is 2.2KW 400HZ 220V. Made by Zhong Hua Jiang.

Was originally on a Delta C200 vfd. That is 220 single phase.

Click the link to add information to this solution:
I PURCHASED A VFD AND SPINDLE FROM FRIEND, HIS SET UP IS 220. DON'T HAVE 220 IN MY SHOP. QUESTION CAN USE YOUR 110 WITH THIS SPINDLE??

Yes, if you need a replacement part on your machine please call us at 281-815-7701.

Click the link to add information to this solution:
I have a blacktooth laser engraver. The Y Axis stepper motor needs to be replaced. Can you please provide me with the information I would need to replace this motor.

The largest CNC machine we make at this time (12/04/2015) is the GreenBull 6'x12' model. This model has 2 options for Z-axis travel.

The short-z option has a total Z travel of 5.75 inches. From that you would subtract the length of the end mill used and the thickness of the spoil board to determine the maximum material thickness. (Example: If the end mill extends 1.25" from the collet and the spoil board is .75", then the material could be up to 5.75 - 1.25 - 0.75 = 3.75 inches in thickness). This is good for most sheet-type materials.

The long-z option, used mainly for large 3D carvings, requires a custom frame and allows for up to 36" of travel.

The tolerance of our machines, like any machine, depends on several variables. The major variables include the manufacturing tolerance, the type of machine control used, the precision of assembly, the thoroughness of maintenance, and the initial and ongoing calibration of the machine. Because we sell kits only most of these variables are outside our control. Therefore, we are hesitant to guarantee a certain level of tolerance for an end user. However, in our experience, tolerances of .001" are readily achievable with our machines.

Additional Information:

Click the link to add information to this solution:
What tolerance can I expect from your largest cnc machine and the laser cutter? Also, what depth can I get on the z axis?

Our hold down method is screws. For a 4'x8' 3/4" sheet, we use 6 screws around the perimeter of the sheet. This provides sufficient hold down for milling. For the vertically oriented machine, the sheet also rests on a small ledge, making it easy for the board to maintain position while fastening.

Click the link to add information to this solution:
Can the vertical CNC router do about what a horizontal router can, like cutting out 3/4" cabinet doors from a 4'X8' formica clad sheet? If so, how do you hold it - with Vacuum? Is a vacuum system available?