[ Log In ]
[ Register ]
NEW: CNC Router PLANS Available for all of our Newest CNC Models!! Click here to "Design Your CNC".

Question #: 14321

Question: Is CW the steps

Current Solution

blueChick:

X-axis
“CW230 (3.0A) Driver”
Set to 1/16 Microstep, 2.7A
Dipswitches: 11001100
Mach3 Motor Tuning: 1422.22 steps/in

Y-axis
“CW230 (3.0A) Driver”
Set to 1/16 Microstep, 2.7A
Dipswitches: 11001100
Mach3 Motor Tuning: 1422.22 steps/in

Z-axis
“CW230 (3.0A) Driver”
Set to 1/4 Microstep, 2.7A
Dipswitches: 10101100
Mach3 Motor Tuning: 1600 steps/in

blackToe:

X-axis
“CW230 (3.0A) Driver”
Set to 1/16 Microstep, 2.7A
Dipswitches: 11001100
Mach3 Motor Tuning: 1422.22 steps/in

Y-axis
“CW230 (3.0A) Driver”
Set to 1/16 Microstep, 2.7A
Dipswitches: 11001100
Mach3 Motor Tuning: 1422.22 steps/in

Z-axis
“CW230 (3.0A) Driver”
Set to 1/4 Microstep, 2.7A
Dipswitches: 10101100
Mach3 Motor Tuning: 1600 steps/in

blackFoot:

X-axis
“CW8060 (6.0A) Driver”
Set to 1/16 Microstep, 2.7A
Dipswitches: 11001100 (“0”=down, “1”=up)
Mach3 Motor Tuning: 914.29 steps/in

Y-axis
“CW230 (3.0A) Driver”
Set to 1/16 Microstep, 2.7A
Dipswitches: 11001100
Mach3 Motor Tuning: 1422.22 steps/in

Z-axis
“CW230 (3.0A) Driver”
Set to 1/4 Microstep, 2.7A
Dipswitches: 10101100
Mach3 Motor Tuning: 1600 steps/in

greenBull:

X-axis
“CW8060 (6.0A) Driver”
Set to 5.43A, 1/16 Microstep
Dipswitches: 01100110 (“0”=down, “1”=up)
Mach3 Motor Tuning: 914.29 steps/in

Y-axis
“CW8060 (6.0A) Driver”
Set to 5.43A, 1/16 Microstep
Dipswitches: 01100110
Mach3 Motor Tuning: 914.29 steps/in

Z-axis
“CW8060 (6.0A) Driver”
Set to 5.43A, 1/4 Microstep
Dipswitches: 01100100
Mach3 Motor Tuning: 1600 steps/in


Scratch-Build / Book-Build Kit:

X-axis
“CW230 (3.0A) Driver”
Set to 1/4 Microstep, 2.7A
Dipswitches: 10101100 (“0”=down, “1”=up)
Mach3 Motor Tuning: 1600 steps/in

Y-axis
“CW230 (3.0A) Driver”
Set to 1/4 Microstep, 2.7A
Dipswitches: 10101100
Mach3 Motor Tuning: 1600 steps/in

Z-axis
“CW230 (3.0A) Driver”
Set to 1/4 Microstep, 2.7A
Dipswitches: 10101100
Mach3 Motor Tuning: 1600 steps/in

Additional Information:


Additional Information:
Scratch built/book CNC with NEMA 34 motors and CW8060 microstep driver

Additional Information:

Respond:

Other Possible Solutions to this Question

  • HOW DO DETERMINE THE STEPS PER INCH

    blueChick:

    X-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    blackToe:

    X-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    blackFoot:

    X-axis
    “CW8060 (6.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100 (“0”=down, “1”=up)
    Mach3 Motor Tuning: 914.29 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    greenBull:

    X-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/16 Microstep
    Dipswitches: 01100110 (“0”=down, “1”=up)
    Mach3 Motor Tuning: 914.29 steps/in

    Y-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/16 Microstep
    Dipswitches: 01100110
    Mach3 Motor Tuning: 914.29 steps/in

    Z-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/4 Microstep
    Dipswitches: 01100100
    Mach3 Motor Tuning: 1600 steps/in


    Scratch-Build / Book-Build Kit:

    X-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100 (“0”=down, “1”=up)
    Mach3 Motor Tuning: 1600 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    Additional Information:


    Additional Information:
    Scratch built/book CNC with NEMA 34 motors and CW8060 microstep driver

    Additional Information:

    Click the link to respond:
    HOW DO DETERMINE THE STEPS PER INCH

  • WHAT IS THE FORMULA TO DETERMINE STEPS PER INCH OR RESOLUTION FOR EACH AXIS?

    The formula and calculation is a starting point to get into the area of steps per inch. You will then need to use the mach3 calibration utility to get the exact steps per inch.

    Formula:
    step per inch = (motor steps * microstepping) / (travel at one turn of the motor in inches)
    if microstepping is set at 16 (1/16 on the driver) then and you are using a sprocket and chain with a pitch of .25 inches and 12 teeth on the drive sprocket
    = (200 * 16) / (12 * .25)
    = 3200 / 3
    = 1066.666 steps per inch

    For lead screw that has a travel of .5 inches at one turn like the 5 start 1/2 inch lead screw and using 4 microsteps per step (1/4):
    = (200 * 4) / (.5)
    = 800 / .5
    = 1600 steps per inch

    Remember to use the mach3 calibration wizard and double check the driver microstep setting.

    Additional Information:

    Click the link to respond:
    WHAT IS THE FORMULA TO DETERMINE STEPS PER INCH OR RESOLUTION FOR EACH AXIS?

  • Why is my motor loosing steps

    Sometimes the problem is just too much dust on the motors. Wood dust and grease can get pretty sticky over time. This is especially bad with lead screws as the dirt is collected inside the nut. Just clean the motors and guides, put some petrol on them to get rid of old, sticky oil, clean again and relube.

    I would look for worn bearings (or perhaps mounting bolts, or even a loose set screw on the motor couplings). You might even go to the extreme, of removing the motor coupling from the drive, and try turning the drive by hand. If you can't, then you have some type of binding issues in the mechanical drive on that axis. Again, look for worn bearings, etc. I once had this issue to appear on my Y axis, and discovered that it had been dragging a shattered bearing around (instead of it smoothly rolling along, as it was designed to do).

    This could also be caused be a loose sprocket appearing like the motor is loosing steps.

    Click the link to respond:
    Why is my motor loosing steps

  • how do I determine the steps per inch for the motors?

    blueChick:

    X-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    blackToe:

    X-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    blackFoot:

    X-axis
    “CW8060 (6.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100 (“0”=down, “1”=up)
    Mach3 Motor Tuning: 914.29 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    greenBull:

    X-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/16 Microstep
    Dipswitches: 01100110 (“0”=down, “1”=up)
    Mach3 Motor Tuning: 914.29 steps/in

    Y-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/16 Microstep
    Dipswitches: 01100110
    Mach3 Motor Tuning: 914.29 steps/in

    Z-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/4 Microstep
    Dipswitches: 01100100
    Mach3 Motor Tuning: 1600 steps/in


    Scratch-Build / Book-Build Kit:

    X-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100 (“0”=down, “1”=up)
    Mach3 Motor Tuning: 1600 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    Additional Information:


    Additional Information:
    Scratch built/book CNC with NEMA 34 motors and CW8060 microstep driver

    Additional Information:

    Click the link to respond:
    how do I determine the steps per inch for the motors?

  • Why is my stepping motor loosing steps.

    Sometimes the problem is just too much dust on the motors. Wood dust and grease can get pretty sticky over time. This is especially bad with lead screws as the dirt is collected inside the nut. Just clean the motors and guides, put some petrol on them to get rid of old, sticky oil, clean again and relube.

    I would look for worn bearings (or perhaps mounting bolts, or even a loose set screw on the motor couplings). You might even go to the extreme, of removing the motor coupling from the drive, and try turning the drive by hand. If you can't, then you have some type of binding issues in the mechanical drive on that axis. Again, look for worn bearings, etc. I once had this issue to appear on my Y axis, and discovered that it had been dragging a shattered bearing around (instead of it smoothly rolling along, as it was designed to do).

    This could also be caused be a loose sprocket appearing like the motor is loosing steps.

    Click the link to respond:
    Why is my stepping motor loosing steps.

  • With a 1/2 lead screw what is the optimal steps for the stepper motor driver 1/16, 1/8, 1/4 etc

    We typically use a 1/4 microstepping for lead screws, but you want to determine the microstepping only after you determine what resolution you want on that axis of the machine.

    The formula:
    Resolution is steps per inch or steps per milimeter

    I will go over this using steps/inch:
    steps = motor steps x driver microstepping
    inch = the amount of travel with one full stepper motor rotation

    In the case of our 1/2" 5 start 10 TPI lead screw, the axis will travel .5 inches with one stepper motor rotation.

    Let's use 1/4 microstepping (4 microsteps for each stepper motor step)

    Therefore:
    (200 steps x 4) / .5 inches =
    800 steps / .5 inches =
    1600 steps/inch

    Now let's use 1/2 microstepping (2 mistrosteps)

    (200 steps x 2) / .5 inches =
    400 steps / .5 inches =
    800 steps/inch

    Remember that increasing microsteps, the torque is also reduced, but the smoothness from the motor is increased.

    Click the link to respond:
    With a 1/2 lead screw what is the optimal steps for the stepper motor driver 1/16, 1/8, 1/4 etc

  • WHO IS THE BRAIN

    The ALL POWERFULL!!!

    Click the link to respond:
    WHO IS THE BRAIN

  • WHO IS YOUR FATHER

    It is the same machine. However, the one on our site comes with a instructional DVD.

    Click the link to respond:
    WHO IS YOUR FATHER

  • IS THE FLU SERIOUS?

    Influenza is the most frequent cause of death from a vaccine-preventable disease in the United States. From 1990 through 1999, an average of approximately 36,000 influenza-associated pulmonary and circulatory deaths occurred during each influenza season. In addition to fatalities, seasonal influenza is also responsible for more than 200,000 hospitalizations per year. Rates of infection from seasonal influenza are highest among children, but the risks for complications, hospitalizations, and deaths are higher among adults ages 65 and older, children younger than 5 years, and people of any age who have medical conditions that place them at increased risk for complications from influenza.

    A novel H1N1 virus was first detected in March of 2009 and quickly spread to pandemic levels. In the U.S., it is estimated that approximately 43-89 million persons became ill with 2009 pandemic H1N1 from April 2009 to April 2010. The virus also resulted in significant hospitalizations and deaths among children, adults 19-65 years, obese persons, and pregnant and post-partum women.

    Click the link to respond:
    IS THE FLU SERIOUS?

  • WHY IS THE SKY BLUE?

    Sunlight reaches Earth's atmosphere and is scattered in all directions by all the gases and particles in the air. Blue light is scattered in all directions by the tiny molecules of air in Earth's atmosphere. Blue is scattered more than other colors because it travels as shorter, smaller waves. This is why we see a blue sky most of the time.

    Click the link to respond:
    WHY IS THE SKY BLUE?

  • Where is the sunset?

    The sun sets on the western horizon.

    Click the link to respond:
    Where is the sunset?

  • how old is the brain?

    The brain was born on August 27th, 2012.

    Click the link to respond:
    how old is the brain?

  • HOW MANY STEPS PER INCH?

    blueChick:

    X-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    blackToe:

    X-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    blackFoot:

    X-axis
    “CW8060 (6.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100 (“0”=down, “1”=up)
    Mach3 Motor Tuning: 914.29 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    greenBull:

    X-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/16 Microstep
    Dipswitches: 01100110 (“0”=down, “1”=up)
    Mach3 Motor Tuning: 914.29 steps/in

    Y-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/16 Microstep
    Dipswitches: 01100110
    Mach3 Motor Tuning: 914.29 steps/in

    Z-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/4 Microstep
    Dipswitches: 01100100
    Mach3 Motor Tuning: 1600 steps/in


    Scratch-Build / Book-Build Kit:

    X-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100 (“0”=down, “1”=up)
    Mach3 Motor Tuning: 1600 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    Additional Information:


    Additional Information:
    Scratch built/book CNC with NEMA 34 motors and CW8060 microstep driver

    Additional Information:

    Click the link to respond:
    HOW MANY STEPS PER INCH?

  • What is the return policy?

    You can return any product within 30 days. There is a 10% restocking fee associated with this return.

    The return policy is stated on the terms of use for the website: https://www.buildyourcnc.com/terms.aspx

    Click the link to respond:
    What is the return policy?

  • how wide is the laser beam?

    A laser beam that exits from the CO2 tube is about the diameter of a standard pencil. The beam passes through a lens that allows this wider beam to converge to a point at the focal length determined by the shape of the lens. The farther above or below the focal point, the wider the beam will get.

    Click the link to respond:
    how wide is the laser beam?

  • what is the meaning of life?

    To be able to fabricate everything, including children!

    Click the link to respond:
    what is the meaning of life?

  • what is the largest machine?

    The largest machine we have is the greenBull cnc machine. There are two sizes for this machine, but the largest width is 6 feet and is intended to have 12 feet of travel length.

    Click the link to respond:
    what is the largest machine?

  • where is the company located

    We are located in Katy, TX

    Our Address is:
    20734 Settlers Lake Cir N.
    Katy, TX 77449

    Click the link to respond:
    where is the company located

  • What is on the combo #1 dvd?

    For the combo DVD there is 2 packages as seen on the website(https://www.buildyourcnc.com/cnckitintro.aspx) and on the DVD and plan combo you only get the plans and the DVD. However the combo with the hardware you will receive the Plans and Assembly DVD.

    Screws:
    #8 or #10 Screws 2" in length- 12
    1/4" diameter - Pan Head
    1" - 12
    1 1/2" - 6
    2" - 20
    3" - 8
    1/4" Diameter - Angled Head 1" - 16
    Bolts:
    1/4" Diameter
    1" - 10
    1 1/2" - 6
    2" - 28
    5/16" - Diameter
    3/4" - 24
    Nuts:
    #8 or #10 - 36
    1/4" - 30
    5/16" - 24
    1/2" - 15 (13 TPI Allthread Compatible, not ACME Precision)
    Cross dowels - 52
    Mechanical:
    Couplings 1/4" to 1/2" with center bunas - 3
    Bearings 1/2" Inside Diameter - 6
    Bearings 5/16" Inside Diameter - 24
    Aluminum Angles to serve as bearing trucks - 6

    Click the link to respond:
    What is on the combo #1 dvd?