To connect the stepper motor drivers to the Mach3 USB interface card, you will need to follow the wiring diagram here: https://www.buildyourcnc.com/Documents/Electric%20Wiring%20Diagram.pdf
which can be found here: https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board along with all of the other manuals associated with that interface card.

Please note that the DC+ and DC- on that wiring diagram (power supply to thye stepper motor drivers) is not correct. The DC- is connected to GND on the drivers and the DC+ is connected to VCC on the drivers. Typically, the DC+ on the power supply is labeled V+ and the DC- is labeled either COM or V-.

If you are having any issues with the wiring, please let me know and I will elaborate. Thanks.

Click the link to add information to this solution:
Yawl sold me a ST-USB MOTION CARD I have surched all your electronics and can't find wring instructions I need to know where to connect X,Y and Z to this controler

The blackFoot CNC machine kit does not include a table. The table can be made as long or shot as you need. for instance, if you are looking for a travel of 4 fet x 4 feet, then the table will need to be about 6 feet long to get the full 4 feet of travel.

The electronics are very straight forward using the connection diagram for the breakout board that you select. Use the videos for a general idea and then use the connection diagram to verify the correct connections for the interface of your choosing.

Yes,the USB interface replaces the breakout board, but remember that you will need to use the planet-cnc software with the USB interface.

Additional Information:
The electronics does accompany the cnc machine kits as long as you select the option "with electronics". There are option to purchase the machines without electronics and that would be necessary if you either have your own electronics, or you prefer the plug and play cnc computer system we call the redLeaf, or redSprout. This will also be necessary if you prefer the electronics that use the USB interface rather than the parallel interface.

Additional Information:

Click the link to add information to this solution:
WHERE ARE THE ELECTRONICS WIRING VIDEOS?

The electronics and wiring videos are located under the tutorials section (click Tutorials on the top menu. The Title is "CNC Electronics and Wiring". The actual link to these videos is: https://www.buildyourcnc.com/CNCElectronicsandWiring.aspx

Additional Information:
You will also find the electronic wiring videos for the USB controller at: https://www.buildyourcnc.com/tutorials/tutorial-Electronics-USB-Interface-Wiring

Click the link to add information to this solution:
WHERE ARE THE ELECTRONICS WIRING VIDEOS?

You can find the wiring diagram for the Mach3 USB card on its product page here:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Here is a direct link to the diagram:
https://www.buildyourcnc.com/Documents/Electric%20Wiring%20Diagram.pdf

Click the link to add information to this solution:
I need wiring instructions for the ST- USB MOTION CARD

We provide a one year warranty from the date the item is delivered.

Click the link to add information to this solution:
WHAT IS THE WARRANTY ON YOUR PRODUCTS

Here is the wiring diagram for the MAch3 USB breakout board:
https://www.buildyourcnc.com/Documents/Electric%20Wiring%20Diagram.pdf

You will need 24 volt relays for the output on that board since that side of the board requires 24 volt power at the V+ and V-

Customer Response:
My inquiry is for the Planet CNC USB and 5v relays.
I am 99% finished with my 2 axis lathe build and this is the last item for me to conquer.
I want to control power to router, and vacuum with the BOB going through the 5V relays purchased on this site.
Thanks again.

Using the Mist, spindle or flood pins...

Buildyourcnc response:
There is an IN, GND and 5V for the digital side to engage the relay. There is an S, O and P for the power line of the device to be controlled.

The 5V and GND must be connected to the 5V and GND from the USB board. The IN is the wire from the output terminal (i.e. mist, flood, spindle).

For the power side, here are the scenarios:
- P to O connection is normally open
- P to S connection is normally closed

So, if you have the power wire that would plug into the wall, the L "black" wire from the power cord will pass through this part of the circuit (cutting the wire and one end in the P terminal and the other end in the O or S terminal). Generally, the P to O is used as this connection is normally open and when the relay is engaged, the circuit will close allowing the current to flow through that wire.

Click the link to add information to this solution:
SIGNAL AND 5V POWER WIRING DIAGRAM FOR RELAY USB BR ABOUT BOARD.

Yes you can. We well the ArtCAM software and modules.

Click the link to add information to this solution:
I SEE ARTCAM MODULES ON YOUR SITE, CAN STILL GET THEM THROUGH YOU?

You can find the wiring diagrams for the blackTooth on step 105 and 106 on the list of instructions on the blackTooth page. Step 105 pertains to the parallel breakout board and step 106 pertains to the USB interface board.

Additional Information:
wire size

Click the link to add information to this solution:
WHERE ARE THE WIRING DIAGRAMS FOR BLACKTOOTH LASER CUTTER IN INSTRUCTIONS?

A cell phone emits electromagnetic radiation of various frequencies at very low intensity and would not affect the development of a fetus whose mother placed the cell phone on her abdomen during her pregnancy. The mother's reproductive and developmental risk for her growing embryo would not be altered by these exposures. If you are healthy, young, and have no reproductive problems or family history of reproductive or developmental problems, your risk for birth defects is 3% and for miscarriage, 15%. These are background risks with which every woman begins her pregnancy. Neither you nor I can change these risks. Good luck with your pregnancy.

Robert Brent, MD, PhD

Click the link to add information to this solution:
DOES CELL PHONE VIBRATION ON YOUR STOMACH DURING PREGNANCY AFFECT THE BABY?

Yes, we sell collets for the porter cable 892

http://www.buildyourcnc.com/collets.aspx

http://www.buildyourcnc.com/item/router-colletnut-router-collet-nut
http://www.buildyourcnc.com/item/router-collet-er20-router-complete-collet-kit
http://www.buildyourcnc.com/item/router-collet-!5-er20-router-collet
http://www.buildyourcnc.com/item/router-collet-!25-er20-router-collet
http://www.buildyourcnc.com/item/router-collet-!125-er20-router-collet

Click the link to add information to this solution:
WE HAVE PORTER CABLE 892, WILL YOUR COLLETS FIT?

The collet in the 1.5 kW spindle is an ER-11 and cannot reach the 1/2" size. I would consider the 2.2 kW spindle instead.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
WHAT SIZE COLLET IS IN YOUR 1.5 KILOWATT SPINDLE?

No. In general, registration is voluntary. Copyright exists from the moment the work is created. You will have to register, however, if you wish to bring a lawsuit for infringement of a U.S. work.

Click the link to add information to this solution:
DO I HAVE TO REGISTER WITH YOUR OFFICE BE PROTECTED?

I can't think of any reason that it would be dangerous. However, I checked with the Cellular Telecommunications Industry Association. The Chairman of the Association sent the following memo on 18 June 1999, to the Associations' Board of Directors and others:
"You may have received inquiries about wireless phones causing fires or explosions at gas stations. In particular, you may have been asked about an alleged explosion at a gas station in Indonesia. We have been unable to verify any such occurrence in Indonesia or anywhere else. Moreover, in our discussions with Shell Oil they have stated they have attempted to verify these reports and also have not been able to document any such occurrence."
Nonetheless, in an abundance of caution, some manufacturers have included language in the owner's manuals for their products that recommends wireless phone users turn off their phones while at refueling points (gas stations). In addition, we have received information that Exxon will begin issuing warning signs at all domestic gas stations advising drivers to turn off all wireless communications devices when entering Exxon gas stations.

While wireless phone owners should always consult their owner's manual for information on the use of the phone, we are not aware of any incident that would justify these concerns."

Gen Roessler, Editor
HPS website

Click the link to add information to this solution:
IS IT DANGEROUS TO USE YOUR CELL PHONE AT A GAS STATION?

There are several CAD/CAM programs out there for MacOS. Here is a list of a few: http://www.macuser.de/forum/f53/3d-2d-cad-395058/#post4499316
I've also read good things about punchCAD: http://www.punchcad.com/
Of course, there is always SketchUp if you are in a pinch. There are a few CAM plugins for SketchUp as well, but I've never used them, so I can't vouch for them.

CAD/CAM will get you as far as designing your parts and producing the g-code, but if you also want to run the CNC machine with your Mac, you will need a piece of software similar to Mach3 or EMC to run the g-code. I haven't been able to find anything like these programs that runs on Mac, so you may have to run Mach3 or EMC in Windows using Boot Camp or a virtual machine such as VMware or Parallels.

Personally, I would use the Mac to do all the CAD/CAM, then use a cheap PC to run the CNC machine.

Additional Information:


Additional Information:
EasyDNC for OSX
www.dnc-x.com

Additional Information:


Additional Information:
Hi guys I’m new to the cnc and I’m beginning to learn how to operate and cad-cam software also my cnc runs on Mach3 my questions is if I should use MacBook to do all designs if I can have all this software to run on Mac or I have to use windows software to operate it? I have separate small computer connected to the cnc table who have Mach3 on it please help. Also if you know any other software much easy for beginners please let me know thank you guys!
My email if needed is r1jastrzebski@gmail.com

Additional Information:


Additional Information:
Hi , thank you for your advise!

Additional Information:
Hi , thank you for your advise!

Additional Information:
Hi , thank you for your advise!

Additional Information:
Hi , thank you for your advise!

Additional Information:

Click the link to add information to this solution:
YOUR CNC SOFTWARE COMPATIBLE WITH MAC?

Tinnitus . Learn to love it. No really you should see a doctor. Make sure. White noise will help you sleep when it gets loud.

Additional Information:
I learned, too late, that if a sudden loud event causes tinnitus, see an audiologist IMMEDIATELY. They can do something about it if addressed within a day or so.

Wear hearing protection...always. Loud noises trigger my tinnitus, and headphones and ear plugs (when out & about or at the movies, subway, etc) help tremendously. Mine are rated 33dB.

Click the link to add information to this solution:
WHAT CAUSES RINGING IN YOUR EAR AND HOW CAN YOU STOP IT?

Limit switches are not really needed for this level of a machine, but if you do want to use them, then you will need to connect them with shielded cable and ground the shield at both ends and any other non-used wire in the cable. Limit switches are very susceptible to the motor interference. You will also need to adjust the debounce in the software you will use.

Click the link to add information to this solution:
DO NEED LIMIT SWITCHES, IF SO WHAT IS YOUR RECOMMENDATION?

The plasma nozzle must be close to the cutting area and you will need some way to keep the nozzle at the right level with some type of device. The spray is downward, so you will need a contained area with a sheet of water at the bottom to extinguish he spray. You should have no problem using our machines for this application since you would need to product the table bed.

Click the link to add information to this solution:
CAN YOUR PRODUCTS OF MACHINES BE USED TO CREATE PLASMA TABLE?

The motor that is attached to the 4th axis is wired as follows:

The motor should have red, green yellow and blue wires coming form the motor. The red and green are paired as one coil and the yellow and blue is paired as the other coil. You can wire the motor to a 3.0 amp driver with red to A+, green to A-, Yellow to B+ and Blue to B-

Click the link to add information to this solution:
HOW DO I WIRE THE 4TH AXIS THAT YOU SELL. I HAVE MACH3 SOFTWARE. NO INSTRUCTIONS ON YOUR SITE

Yes, it is found in laser components section

Click the link to add information to this solution:
DO YOU GUYS SELL THE POTENTIOMETER FOR YOUR LASER SYSTEM BY ITSELF