No the USB board is a stand alone purchase, you can find the needed USB cable here: https://buildyourcnc.com/item/electronicsAndMotors-cable-wire-USB-2!0-Cable-TypeA-Male-To-TypeB-Male-newbiehack-Cables_and_Wires-USB-2!0-Cable-TypeA-Male-To-TypeB-Male

Click the link to add information to this solution:
So does it come with. A control box and router

The motor cables for the blackToe are as follows:

Total 30 feet

X - 9
Y - 10
Z - 11

Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
WHAT CABLE LENGTHS SHOULD USE FOR THE BLACKTOE

We still use Mach3 with a parallel port. We are looking into newer boards with USB/ethernet communication.

Click the link to add information to this solution:
Are you using Mach 3 or 4? Do you ever use the etherenet outlet to control drivers?

If you select the Settings Page and select or tick Auto Limit Override - this will allow you to back off the switch.

Additional Information:
limit and home switch

Click the link to add information to this solution:
IS THERE A WAY TO GET RID OF THE PARALLEL CABLE AND SOMEHOW USE USB ?

The blackfoot requires a total of 50 feet of cable.

The X axis needs 15 feet
The Y axis needs 17 feet
and the Z-axis needs 18 feet

These are 20 gauge 4 conductor cable.

Additional Information:

Click the link to add information to this solution:
WHAT CABLE LENGTHS SHOULD USE FOR THE BLACKFOOT CNC MACHINE

Copyright protects original works of authorship, while a patent protects inventions or discoveries. Ideas and discoveries are not protected by the copyright law, although the way in which they are expressed may be. A trademark protects words, phrases, symbols, or designs identifying the source of the goods or services of one party and distinguishing them from those of others.

Click the link to add information to this solution:
HOW A COPYRIGHT DIFFERENT FROM PATENT OR TRADEMARK?

The password is: 608

Click the link to add information to this solution:
WHAT IS THE SYSTEM PASSWORD FOR LASER CONTROL UNIT?

Nema 23 stepping motors with 100 oz-in rated holding torque and 1/4" shaft.

Click the link to add information to this solution:
WHAT MOTORS DOES THE BLACK TOOTH USE?

Nema 23 stepping motors with 100 oz-in rated holding torque and 1/4" shaft.

Click the link to add information to this solution:
WHAT MOTORS DOES THE BLACK TOOTH USE?

Yes and properly soldered.

Additional Information:
20

Click the link to add information to this solution:
DO YOU SUPPLY THE MALE PORTION OF MOTOR CONTROL CABLES WITH REDLEAF?

The motor cables for the blackToe are as follows:

Total 30 feet

X - 9
Y - 10
Z - 11

Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
WHAT CABLE LENGTHS ARE USED FOR THE BLACKTOE

The spindle inverter (VFD) will run on a 220V (or between 170V-250V) power source with either 50Hz or 60Hz.

Click the link to add information to this solution:
DOES THE SPINDLE RUN ON A 50HZ POWER SOURCE?

The motor cables for the blackToe are as follows:

Total 30 feet

X - 9
Y - 10
Z - 11

Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
THE BLACKTOE REQUIRES HOW MUCH MOTOR CABLE

The parallel (printer cable) port is uses the computer as its main source of pulse trains to operate the motor driver directly. Parallel ports are a direct connection from the processor commonly referred to as GPIO pins (General Purpose I/O pins) and provides a convenient and powerful way to interface with the computer. The parallel breakout board is included in those kits only to condition those signals for use with the drivers.

The USB serves at the actual controller, sending the pulse trains, but the computer sends simple human readable instructions to the USB controller to tell the controller how to send pulses.

The non-technical differences that may serve as the most important information to you is that the parallel configurations allow for a wider variety of industry standard software that can be used to control the cnc machine. The USB that we offer requires the operator to use a software called Planet-CNC software which is a very well made and feature full cnc control software.

Additional Information:


Additional Information:


Additional Information:
USB Motion controller breakout board work with planet cnc software?

Click the link to add information to this solution:
WHAT IS THE DIFFERENCE BETWEEN A PRINTER CABLE PORT AND USB MOTOR KITS

The recommended total length of motor cable should be 15 feet for the blueChick v4.2

Z - 6 feet
Y - 5 feet
X- 4 feet

20 AWG 4 conductor

If your drivers will be positioned farther from the machine, you may need longer cable.

Additional Information:

Click the link to add information to this solution:
HOW MUCH MOTOR CABLE SHOULD PURCHASE FOR THE BLUECHICK

Controlling a 3-axis or 4-axis motor configuration, you will need the following items drivers/motors/controller. Our electronics combo comes with the items mentioned and with power supply/miscellaneous items.
The only other item needed will be a computer (with controller software) to communicate and view controls of your motors.
Using the Parallel breakout board will use Mach 3 software, and USB will use Planet-CNC software.

Additional Information:
You can use this link to see the videos on how to connect the electronics together and make them work: https://www.buildyourcnc.com/tutorials/tutorial-Electronics-USB-Interface-Wiring

Click the link to add information to this solution:
hey, where can i see the steps how can i control 3 or 4 step motor? can i use the Axis Electronics Combo? or i need to connect controller?

The motor cables for the blackToe are as follows:

Total 30 feet

X - 9
Y - 10
Z - 11

Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
WHAT ARE THE CABLE LENGTHS FOR BLACKTOE

The motor cables for the blackToe are as follows:

Total 30 feet

X - 9
Y - 10
Z - 11

Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
WHAT ARE THE CABLE LENGTHS FOR BLACKTOE

The motor cables for the blackToe are as follows:

Total 30 feet

X - 9
Y - 10
Z - 11

Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
HOW MUCH MOTOR CABLE FOR THE BLACKFOOT?