Yes, the blueChick kits are available. You can get the shipping rates automatically in the shopping cart. There will be a calculate shipping button on the enter shipping information section of the shopping cart.

Click the link to add information to this solution:
CAN YOU PLEASE TELL ME THE AVAILABILITY OF 12X36 BLUE CHICK 4.2, AND COST FOR SHIPPING TO ZIP 72802 IN RUSSELLVILLE, ARKANSAS?

I don't see anything in the datasheet for the relay that indicates an overheat condition. While the relay is engaged, the power consumption is 400 mW and I don't believe this is enough to raise the temperature faster than the heat dissipation from the metal on the leads through convection or radiation outside of the rated temperature working ranges providing that you maintain an ambient temperature range within -40°C to 85°C (with no icing or condensation).

http://www.omron.com/ecb/products/pdf/en-g2rl.pdf

Click the link to add information to this solution:
IS IT OK TO LEAVE THE VACUUM PRESSURE CONTROLLER PLUGGED IN ALL TIME WHEN PUMP SWITCHED OFF?

All of our CNC machines can cut melamine. If your application (kitchen doors) requires large cutting area, then I would recommend the following machines:

- greenBull 4x (4'x8'), 5x (5'x10') or 6x (6'x 12')

- greenLean 4'x8' vertically oriented CNC machine

- Or our Fabricator Pro 4'x8' metal CNC machine

Click the link to add information to this solution:
CAN YOU RECOMMEND WHICH CNC MACHINE TO GO WITH FOR CUTTING MELAMINE AND MAKING KITCHEN DOORS FROM MDF. ALSO DO PROVIDE TRAINING ON OPERATING SETTING UP SHOP PRODUCTION USE? THANKS

Yes you can. We well the ArtCAM software and modules.

Click the link to add information to this solution:
I SEE ARTCAM MODULES ON YOUR SITE, CAN STILL GET THEM THROUGH YOU?

Check step 9 on this page: http://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay

Click the link to add information to this solution:
IF YOU HAVE CIRCUIT (OR PICTURE) OF HOW THIS RELAY IS CONNECTED TO THE ROUTER

Hands-free cell phone car microphones have been tested by the manufacturers and meet the current ANSI/IEEE (American National Standards Institute/Institute of Electrical and Electronics Engineers) standards for radiofrequency (RF) safety. These are the same standards that the Federal Communications Commission enforces under the Telecommunications Act of 1996, and they place limits on the specific absorption rate (SAR) of RF energy in the body. Recent inflammatory articles in the British press were not substantiated by testing at ISO-accredited testing facilities at Motorola. Manufacturers of cell phones are required under FCC regulations to assure that their products meet the SAR limits on both hand-held and hands-free units. Further information can be obtained on the Internet at The Center for Devices and Radiological Health (FDA information) or Office of Engineering and Technology (FCC information).

Click the link to add information to this solution:
COULD YOU PLEASE EXPLAIN, IF IT'S TRUE, THAT HANDS-FREE CELL PHONE CAR MICROPHONES RADIATE MORE THAN ANY OTHER INSTRUMENT USED WITH THESE PHONES?

Tinnitus . Learn to love it. No really you should see a doctor. Make sure. White noise will help you sleep when it gets loud.

Additional Information:
I learned, too late, that if a sudden loud event causes tinnitus, see an audiologist IMMEDIATELY. They can do something about it if addressed within a day or so.

Wear hearing protection...always. Loud noises trigger my tinnitus, and headphones and ear plugs (when out & about or at the movies, subway, etc) help tremendously. Mine are rated 33dB.

Click the link to add information to this solution:
WHAT CAUSES RINGING IN YOUR EAR AND HOW CAN YOU STOP IT?

There are two main questions that we can answer with respect to motor torque and the mechanical advantage of lead screws, 1) What torque motor do you need to lift a particular weight, or 2) What maximum weight will my motor torque be able to lift.

This formula uses Newtons (N) as it's final unit. Use this with the included radius (R) to determine the torque. Newtons can easily be converted to lbs or ounces using online conversions.

Effort = Sf + (Load/(2 x pi x (R/p) x Se))

where:
p = pitch of the screw
Se = screw efficiency = Standard lead screw will be between 20% (.2) and 40% (.4)
Sf = static force. This is the force that is needed to start the movement. The number may be eliminated, but it is good to use a number in the 5 N to 20 N range.
Load = the expected load that the effort will need to carry (i.e., the router and the included axis assembly that the motor will need to lift)
R = radius of the lead screw


This formula is based on the "law of the machine"

The final effort amount with its unit of newtons and R will be the torque. For example, if the effort comes to 100 N (newtons) and the R is .5 inches, then you can assume that the effort is 50 N-in since it would take twice the effort to turn form the one inch mark from the center of the shaft.

Example:

Load = 90 N (20.2 lbs)
R = 1 inch since that is the length from the center of the shaft that the motor is rated
p = 1 inch / 13 = .08 inches

Effort = 5 N + (90 N / (2 x 3.14 x (1 / .08) x .2))
Effort = 5 N + (90 N / (6.28 x 12.5 x .2))
Effort = 5 N + (90 N / (15.7))
Effort = 5 N + (5.73 N)
Effort = 10.7 N = 2.4 lbs = 38.4 oz-in

I am putting the oz-in on the end because the formula considers the distance from the center of the shaft to be one inch.

Therefore, a 425 oz-in motor would be able to lift a 20.2 lb Router with its accompanying assembly. If the assembly and router is heavier, plug in the numbers and determine the effort required.

With a bit of algebra, the formula can be rewritten to find the load:

Load = (Effort - Sf) x (2 x pi x (R/p) x Se)

Another formula that does not consider friction at all:

Effort = (Load x p) / (2 x pi x R)

Lets see if we get similar results:

Effort = (20 lb x .08 inches) / (2 x 3.14 x 1)
Effort = 1.6 / 6.28 = .255 lbs = 4.08 oz-in

The results from both formulas appear to be very small because a 13 TPI screw will have enormous mechanical advantage.

It is evident that the first formula that does consider friction that we are loosely estimating is far more conservative than the second formula. Either way, even the most conservative formula shows that the 425 oz-in motor will handle very large weights. If you are using a lead screw with only two turns per inch, .5 inch pitch, you can determine the requirements with the first formula.

Example for a 10 TPI 5 start (2 turns per inch) lead screw:

Load = 90 N (20.2 lbs)
R = 1 inch since that is the length from the center of the shaft that the motor is rated
p = 1 inch / 2 = .5 inches

Effort = 5 N + (90 N / (2 x 3.14 x (1 / .5) x .2))
Effort = 5 N + (90 N / (6.28 x 2 x .2))
Effort = 5 N + (90 N / (2.512))
Effort = 5 N + (35.83 N)
Effort = 40.828 N = 9.18 lbs = 146.88 oz-in

Customer Response:
thank you so much

Additional Information:


Additional Information:


Additional Information:
how do i calculate torque of stepper motor if lead screw coupled to motor shaft and load applied by lead screw on plate is 100 kg by vertically

Additional Information:
Pls


Additional Information:
1m 16mmdiameter ball screws calculations


Additional Information:
What is the max load that 2 NEMA 17 stepper motors (spaced 2 feet apart, both will be pushing up on the same gantry) can lift while using a rod with the following specifications T8 OD 8mm Pitch 2mm Lead 4mm for each motor.

Additional Information:


Additional Information:
1

Click the link to add information to this solution:
HOW DO I DETERMINE THE AMOUNT OF SCREW WEIGTH THAT MY MOTOR CAN HANDLE

Yes and properly soldered.

Additional Information:
20

Click the link to add information to this solution:
DO YOU SUPPLY THE MALE PORTION OF MOTOR CONTROL CABLES WITH REDLEAF?

Hour meter. This will tell you exactly how long your system has been 'on' giving you a more accurate bead on the length of your tubes life.

Click the link to add information to this solution:
WHAT CAN ADD TO MY BLACKTOOTH LASER CUTTER MEASURE THE TIME OF USE?

Temperature probe monitor. Very valuable. This keeps you up to date on your coolant temperature levels.

Voltage meter. This will tell you the exact level of voltage/power you are running telling the laser to run at instead of an arbitrary mark on a drawn wheel around your POT.

Ammeter sensitive to 1mA. This will be sure your not over driving your tube and reducing it's life significantly.

Hour meter. This will tell you exactly how long your system has been 'on' giving you a more accurate bead on the length of your tubes life.

Exhaust fan upgrade. The current fan included is 100CFM. You can buy 120mm fans that push 250CFM and I have included a guide on how to go about doing this here. http://buildyourtools.com/phpBB3/viewto ... 8cdd1802bf

To push the exhaust fan even further, if you have the room/power, I would highly recommend investing in a 600+ CFM "Dust Collector" system. 250CFM is still not suffice to draw all the smoke that can come off of 3mm or 1/8 MDF cutting job.

A cutting surface. I bought myself a aluminum 'egg crate' mesh from my local HVAC company. They are used a cover for fluorescent lights and work great for low impact cutting surface. They come in 4'x8' sheets and are easily cut to fit. The other side is if you can find a steel honeycomb cutting bed to fit. These can be quite costly or fairly affordable depending where you are looking. The benefit of a steel honeycomb is you can use high power magnets to hold material down.

Click the link to add information to this solution:
HOW CAN YOU ENHANCE THE BLACKTOOTH LASER CUTTER?

You can determine if the area is serviceable by:
- selecting the items you want to purchase on the website
- go to the cart (shopping cart top left of any webpage)
- log in, or register
- Enter the address and click on calculate shipping.

The webpage will return the direct rates and whether your area is serviced or not. Feel free to enter any address as long as you are able to receive the package from that address.

Click the link to add information to this solution:
WAS WONDERING IF YOU COULD TELL ME WHETHER OR NOT SHIP ANY OF YOUR KIT PRODUCTS TO THE UK?

The plasma nozzle must be close to the cutting area and you will need some way to keep the nozzle at the right level with some type of device. The spray is downward, so you will need a contained area with a sheet of water at the bottom to extinguish he spray. You should have no problem using our machines for this application since you would need to product the table bed.

Click the link to add information to this solution:
CAN YOUR PRODUCTS OF MACHINES BE USED TO CREATE PLASMA TABLE?

Yes, the customer will need to sign our NDA (Non Disclosure Agreement) form and send it back to us. We will then send the dxf of the specific updated part of the machine.

Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:
UoZD5KPp

Additional Information:
-1 OR 2+416-416-1=0+0+0+1 --

Additional Information:
-1 OR 2+291-291-1=0+0+0+1

Additional Information:
-1' OR 2+657-657-1=0+0+0+1 --

Additional Information:
-1' OR 2+849-849-1=0+0+0+1 or 'WBwHf8k5'='

Additional Information:
-1" OR 2+276-276-1=0+0+0+1 --

Additional Information:
1'"

Additional Information:
1����%2527%2522

Additional Information:
@@z69Jq

Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
CAN I GET DXF FILES FOR THE UPDATED PARTS OF MY MACHINE?

A standard 40W CO2 laser will cut up to 1/4" thick of material, be it wood, acrylic, card stock, leather, fabric, foam, cork, etc. (Decent speed and final cut are heavily dependent on a strong air assist upgrade)

Metals cannot be cut due to the power level and wavelength of the CO2 laser. But it can be marked with special solutions like Cermark or Thermark.

Click the link to add information to this solution:
WHAT THICKNESS OF MATERIAL CAN THE BLACKTOOTH LASER CUT?

You can determine if the country is serviceable by:
- selecting the items you want to purchase on the website
- go to the cart (shopping cart top left of any webpage)
- log in, or register
- Enter the address and click on calculate shipping.

The webpage will return the direct rates and whether your area is serviced or not. Feel free to enter any address as long as you are able to receive the package from that address.

Click the link to add information to this solution:
CAN YOU SEND PRODUCTS TO MY COUNTRY?

Mounting the extruder to the whiteAnt can be done a couple of ways. One is to take the 4 mounting holes located at the lower portion of the z-axis rail support and use long screws protruding out. Take a thinner material and drill the four holes matching the locations of the 4 screws and screw on nuts to hold it in place. The other option would be to use the metal bracket and fasten to the edge of the rail support.

Click the link to add information to this solution:
CAN YOU GIVE ME SOME HELP OR POINT IN THE RIGHT DIRECTION TO INCORPORATE MK 7 EXTRUDER WITH BOOK PLANS FOR 3D PRINTER?

You can determine if the country is serviceable by:
- selecting the items you want to purchase on the website
- go to the cart (shopping cart top left of any webpage)
- log in, or register
- Enter the address and click on calculate shipping.

The webpage will return the direct rates and whether your area is serviced or not. Feel free to enter any address as long as you are able to receive the package from that address.

Click the link to add information to this solution:
CAN YOU SHIP ITEMS TO MY COUNTRY?

This will depend on the VFD you have to identify the correct terminal. The terminal on the VFD will be labeled AI1 typically (Analog Input #1). You will also need to make sure to complete the PWM circuit using the GND terminal on the VFD.

Additional Information:
I have wired my 0-10V signal to the AI1 and GND terminals as suggested. I have also set the PD-01 and PD-02 settings to 1. Still nothing. Is there something else that I am missing?

Additional Information:
Thanks for the information. Can you let me know the model of the VFD that you have?

Additional Information:
VFD Model # YL600-2S-2K20

Additional Information:
Thanks. I will check our resources and documentation to see if there is another programming setting that needs to be changed.

Additional Information:
Does your VFD have a VI terminal?

Additional Information:
No, it does not. The terminals for this VFD are as follows (seperated by dashes "-").

10V-AI1-AO2-PLC-DI5-DI3-DI1-COM
AI2-GND-AO1-DI6-DI4-DI2-FM-24V

Additional Information:
Do you have a PD070 parameter?

PD070 is the main Analog Input parameter.

The options for that parameter is:
0: 0-10V
1: 0-5V
2: 0-20mA
3: 4-20mA
4: 0-10V (4-20mA Stacked)
5: XIA
6: (VI+XIA)/2
7: (3VA+XIA)/4
8: (XIA_XIB)/2
9: Max (XIA, XIB)
10: Min (XIA, XIB)


Additional Information:
There is a PD-00 thru PD-09. PD-07 is currently set to 0.

Additional Information:
It appears that the manual I’m using “Titled YL600” is not the same as your unit. I will check our manuals and find the one that has only PD-00 to PD-09.

Additional Information:
For that VFD, the parameters are P0. The 0 may look like a D on the display.

The parameters that need to be changed for the AI1 to work (Brackets [] around the correct selection):

P0-01: First Motor Control Mode
- 0: Sensorless Vector Control
- 1: Flux Vector Control (FVC)
- [2]: V/F Control

P0-02: Options of Command Source
- 0: Operation Panel Command Channel (LED will be off)
- [1]: Terminal Command Channel (LED will be on)
- 2: Communication Command Channel (LED will flicker)

P0-03: Options of Principle Frequency Source X
- 0: Digital Setting (Preset Frequency P0-08, UP/DOWN modifiable, no power-down memory)
- 1: Digital Setting (Preset Frequency P0-08, UP/DOWN modifiable, with power-down memory)
- [2]: AI1
- 3: AI2
- 4: AI3
- 5: Pulse Setting (DI5)
- 6: Multi Speed Instruction
- 7: Simple PLC
- 8: PID (Proportional Integral Derivative Control)
- 9: Communication Given

P0-11: Upper Limit Frequency Source
- 0: P0-12 (Make sure the P0-12 parameter has the correct max frequency if used)
- [1]: AI1
- 2: AI2
- 3: AI3
- 4: Pulse Setting
- 5: Communication Given

P0-27: Command Source Bundle with Frequency Sources
Single Digit: Options of Operation Panel Command Bundle with Frequency Sources
- 0: No Bundling
- 1: Digital Setting Frequency
- [2]: AI1
- 3: AI2
- 4: AI3
- 5: Pulse Setting (DI5)
- 6: Multi Speed Instruction
- 7: Simple PLC
- 8: PID
- 9: Communication Given
Double Digit: Options of Terminal Command Bundle with Frequency Sources
Hundred Place: Options of Communication Command Bundle with Frequency Sources
Kilobit: Options of Automatic Operation Bundle with Frequency Sources

P2-09: Upper Limit Source of Lower Torque Under Speed Control Mode
- 0: Function Code P2-10 Setting
- [1]: AI1
- 2: AI2
- 3: AI3
- 4: Pulse Setting
- 5: Communication Given
- 6: MIN (Al1, Al2)
- 7: MAX (Al1, Al2)
- Maximum range for options 1-7, accords with P2-10

If you elect to use a different AI#, then configure the parameters (P0-03, P0-11, P0-27 and P2-09) accordingly.

Click the link to add information to this solution:
I'VE BUFFERED A PWM SIGNAL TO 0-10V ANALOG AND I WOULD LIKE USE THAT RUN YOUR 110V 2.2KW SPINDLE VFD. COULD YOU PLEASE DETAIL THE CORRECT WIRING VFD SETTINGS GET WORKING?