[ Log In ]
[ Register ]

Question #: 14812

Question: Do you work on cnc electronics from China?

Current Solution

Yes, you can send your electronics to us for repair, or retrofit to work with either Mach3, Mach4 or LinuxCNC. You can send us an email at customerService@buildyourcnc.com to set up your appointment.

Some of the types of CNC electronics we will consider.

- We will work on electronics from other manufacturers as long as you are ok with the Mach3, Mach4 or LinuxCNC control software for your CNC machine or CNC router.

- We will repair or retrofit used CNC electronics.

- Some customers find that electronics are overwhelming to put together so we will finish these electronics wiring and assembly for you.

The cost for these includes labor cost for the time it takes to finish the CNC electronics repair or retrofit and for any parts that need to be replaced or added.

Here is an example of CNC electronics that we worked on for a customer:



This is the type of response that you can expect to receive after the CNC electronics are repaired or retrofitted to work under Mach3, Mach4 or LinuxCNC. You can see the entire work, which also shows the time involved. We also show what we were able to accomplish at the beginning of the video.

Respond:

Other Possible Solutions to this Question

  • Do you repair cnc electronics from another manufacturer?

    Yes, you can send your electronics to us for repair, or retrofit to work with either Mach3, Mach4 or LinuxCNC. You can send us an email at customerService@buildyourcnc.com to set up your appointment.

    Some of the types of CNC electronics we will consider.

    - We will work on electronics from other manufacturers as long as you are ok with the Mach3, Mach4 or LinuxCNC control software for your CNC machine or CNC router.

    - We will repair or retrofit used CNC electronics.

    - Some customers find that electronics are overwhelming to put together so we will finish these electronics wiring and assembly for you.

    The cost for these includes labor cost for the time it takes to finish the CNC electronics repair or retrofit and for any parts that need to be replaced or added.

    Here is an example of CNC electronics that we worked on for a customer:



    This is the type of response that you can expect to receive after the CNC electronics are repaired or retrofitted to work under Mach3, Mach4 or LinuxCNC. You can see the entire work, which also shows the time involved. We also show what we were able to accomplish at the beginning of the video.

    Click the link to respond:
    Do you repair cnc electronics from another manufacturer?

  • I bought a used cnc router. Can you make the electronics work?

    Yes, you can send your electronics to us for repair, or retrofit to work with either Mach3, Mach4 or LinuxCNC. You can send us an email at customerService@buildyourcnc.com to set up your appointment.

    Some of the types of CNC electronics we will consider.

    - We will work on electronics from other manufacturers as long as you are ok with the Mach3, Mach4 or LinuxCNC control software for your CNC machine or CNC router.

    - We will repair or retrofit used CNC electronics.

    - Some customers find that electronics are overwhelming to put together so we will finish these electronics wiring and assembly for you.

    The cost for these includes labor cost for the time it takes to finish the CNC electronics repair or retrofit and for any parts that need to be replaced or added.

    Here is an example of CNC electronics that we worked on for a customer:



    This is the type of response that you can expect to receive after the CNC electronics are repaired or retrofitted to work under Mach3, Mach4 or LinuxCNC. You can see the entire work, which also shows the time involved. We also show what we were able to accomplish at the beginning of the video.

    Click the link to respond:
    I bought a used cnc router. Can you make the electronics work?

  • What can I do if my cnc electronics doesn't work?

    Yes, you can send your electronics to us for repair, or retrofit to work with either Mach3, Mach4 or LinuxCNC. You can send us an email at customerService@buildyourcnc.com to set up your appointment.

    Some of the types of CNC electronics we will consider.

    - We will work on electronics from other manufacturers as long as you are ok with the Mach3, Mach4 or LinuxCNC control software for your CNC machine or CNC router.

    - We will repair or retrofit used CNC electronics.

    - Some customers find that electronics are overwhelming to put together so we will finish these electronics wiring and assembly for you.

    The cost for these includes labor cost for the time it takes to finish the CNC electronics repair or retrofit and for any parts that need to be replaced or added.

    Here is an example of CNC electronics that we worked on for a customer:



    This is the type of response that you can expect to receive after the CNC electronics are repaired or retrofitted to work under Mach3, Mach4 or LinuxCNC. You can see the entire work, which also shows the time involved. We also show what we were able to accomplish at the beginning of the video.

    Click the link to respond:
    What can I do if my cnc electronics doesn't work?

  • Can you repair the electronics on my CNC machine?

    Yes, you can send your electronics to us for repair, or retrofit to work with either Mach3, Mach4 or LinuxCNC. You can send us an email at customerService@buildyourcnc.com to set up your appointment.

    Some of the types of CNC electronics we will consider.

    - We will work on electronics from other manufacturers as long as you are ok with the Mach3, Mach4 or LinuxCNC control software for your CNC machine or CNC router.

    - We will repair or retrofit used CNC electronics.

    - Some customers find that electronics are overwhelming to put together so we will finish these electronics wiring and assembly for you.

    The cost for these includes labor cost for the time it takes to finish the CNC electronics repair or retrofit and for any parts that need to be replaced or added.

    Here is an example of CNC electronics that we worked on for a customer:



    This is the type of response that you can expect to receive after the CNC electronics are repaired or retrofitted to work under Mach3, Mach4 or LinuxCNC. You can see the entire work, which also shows the time involved. We also show what we were able to accomplish at the beginning of the video.

    Click the link to respond:
    Can you repair the electronics on my CNC machine?

  • Can I send used CNC electronics to you for a retrofit?

    Yes, you can send your electronics to us for repair, or retrofit to work with either Mach3, Mach4 or LinuxCNC. You can send us an email at customerService@buildyourcnc.com to set up your appointment.

    Some of the types of CNC electronics we will consider.

    - We will work on electronics from other manufacturers as long as you are ok with the Mach3, Mach4 or LinuxCNC control software for your CNC machine or CNC router.

    - We will repair or retrofit used CNC electronics.

    - Some customers find that electronics are overwhelming to put together so we will finish these electronics wiring and assembly for you.

    The cost for these includes labor cost for the time it takes to finish the CNC electronics repair or retrofit and for any parts that need to be replaced or added.

    Here is an example of CNC electronics that we worked on for a customer:



    This is the type of response that you can expect to receive after the CNC electronics are repaired or retrofitted to work under Mach3, Mach4 or LinuxCNC. You can see the entire work, which also shows the time involved. We also show what we were able to accomplish at the beginning of the video.

    Click the link to respond:
    Can I send used CNC electronics to you for a retrofit?

  • Can you finish putting my CNC electronics together for me?

    Yes, you can send your electronics to us for repair, or retrofit to work with either Mach3, Mach4 or LinuxCNC. You can send us an email at customerService@buildyourcnc.com to set up your appointment.

    Some of the types of CNC electronics we will consider.

    - We will work on electronics from other manufacturers as long as you are ok with the Mach3, Mach4 or LinuxCNC control software for your CNC machine or CNC router.

    - We will repair or retrofit used CNC electronics.

    - Some customers find that electronics are overwhelming to put together so we will finish these electronics wiring and assembly for you.

    The cost for these includes labor cost for the time it takes to finish the CNC electronics repair or retrofit and for any parts that need to be replaced or added.

    Here is an example of CNC electronics that we worked on for a customer:



    This is the type of response that you can expect to receive after the CNC electronics are repaired or retrofitted to work under Mach3, Mach4 or LinuxCNC. You can see the entire work, which also shows the time involved. We also show what we were able to accomplish at the beginning of the video.

    Click the link to respond:
    Can you finish putting my CNC electronics together for me?

  • Which electronics package is required for the CNC machine from the book designs?

    The book design uses all NEMA 23/24 motors which can be found here:
    https://buildyourcnc.com/item/electronicsAndMotors-3axis-425-elcombo

    I recommend the Mach3 USB option as you will be able to use the USB connection for control.

    If you are planning to build from the plans developed by the folks over at Woodsmith Magazine which is loosely based on the book design, use this electronics package:
    https://buildyourcnc.com/item/electronicsAndMotors-3axis-heavy-gantry-elcombo

    Click the link to respond:
    Which electronics package is required for the CNC machine from the book designs?

  • How do I wire my cnc electronics?

    Yes, you can send your electronics to us for repair, or retrofit to work with either Mach3, Mach4 or LinuxCNC. You can send us an email at customerService@buildyourcnc.com to set up your appointment.

    Some of the types of CNC electronics we will consider.

    - We will work on electronics from other manufacturers as long as you are ok with the Mach3, Mach4 or LinuxCNC control software for your CNC machine or CNC router.

    - We will repair or retrofit used CNC electronics.

    - Some customers find that electronics are overwhelming to put together so we will finish these electronics wiring and assembly for you.

    The cost for these includes labor cost for the time it takes to finish the CNC electronics repair or retrofit and for any parts that need to be replaced or added.

    Here is an example of CNC electronics that we worked on for a customer:



    This is the type of response that you can expect to receive after the CNC electronics are repaired or retrofitted to work under Mach3, Mach4 or LinuxCNC. You can see the entire work, which also shows the time involved. We also show what we were able to accomplish at the beginning of the video.

    Click the link to respond:
    How do I wire my cnc electronics?

  • Do you sell the 3 axis electronics combo , for heavy gantry , with the new Planet CNC usb controller ?

    Unfortunately, we don't sell the planet-cnc controller anymore. They made a change to their software that prohibits us from creating the open source board.

    We do sell three other boards that may work for you.

    The Pokeys57CNC board is the mose feature rich and will work with both Mach3 and Mach4:
    https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

    The MAch3 USB board is a good inexpensive interface that will work well if you need the interface to be USB only:
    https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

    Our in-house parallel breakout board (ytou need a parallel port for this interface to work):
    https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay
    Most motherboards have the parallel port connector on the motherboard, but not as a connector on the back of the computer case.

    Click the link to respond:
    Do you sell the 3 axis electronics combo , for heavy gantry , with the new Planet CNC usb controller ?

  • What doesn't come with the electronics that I will need so it will work?

    Here is a list of the parts needed to get the electronics combo functioning (parallel or USB interface options):

    - 22 or 24 gauge stranded hookup wire to connect all of the drivers to the USB or parallel interface (terminal to terminal connections),
    - 18 gauge stranded hookup wire to connect the drivers to the power supply,
    - a power cable (extension cord) to connect from the power outlet to the power supply,
    - 4 conductor cable to connect the drivers to the stepper motors,
    - a USB cable to connect from the computer to the USB interface (or for power to the parallel interface),
    - for the parallel interface, a parallel cable is needed (male to male db-25),
    - a computer (for parallel interface, the computer will need a parallel port and if the computer does not contain a parallel interface, the motherboard may have a header for it, or you can purchase a parallel adapter to plug into the motherboard, very inexpensive),
    - cnc control software: for the USB interface, you will need planet-cnc software, for the parallel interface, you can use any industry standard cnc control software (the typical is Mach3 for Windows, or EMC2 or Linuxcnc for Linux (Linuxcnc.org).

    5v power supply is not needed. The 5 volts signal level power is derived from the computer through USB on both types of interfaces.

    Click the link to respond:
    What doesn't come with the electronics that I will need so it will work?

  • Can you supply an electronics package for a dual x-axis CNC machine (X, Y, Z)

    Yes, we have a 4 axis combo kit available under Motion Electronics.

    Click the link to respond:
    Can you supply an electronics package for a dual x-axis CNC machine (X, Y, Z)

  • My cnc electronics does not turn on with my spindle. How can I fix it?

    Yes, you can send your electronics to us for repair, or retrofit to work with either Mach3, Mach4 or LinuxCNC. You can send us an email at customerService@buildyourcnc.com to set up your appointment.

    Some of the types of CNC electronics we will consider.

    - We will work on electronics from other manufacturers as long as you are ok with the Mach3, Mach4 or LinuxCNC control software for your CNC machine or CNC router.

    - We will repair or retrofit used CNC electronics.

    - Some customers find that electronics are overwhelming to put together so we will finish these electronics wiring and assembly for you.

    The cost for these includes labor cost for the time it takes to finish the CNC electronics repair or retrofit and for any parts that need to be replaced or added.

    Here is an example of CNC electronics that we worked on for a customer:



    This is the type of response that you can expect to receive after the CNC electronics are repaired or retrofitted to work under Mach3, Mach4 or LinuxCNC. You can see the entire work, which also shows the time involved. We also show what we were able to accomplish at the beginning of the video.

    Click the link to respond:
    My cnc electronics does not turn on with my spindle. How can I fix it?

  • My electronics stopped working

    Yes, you can send your electronics to us for repair, or retrofit to work with either Mach3, Mach4 or LinuxCNC. You can send us an email at customerService@buildyourcnc.com to set up your appointment.

    Some of the types of CNC electronics we will consider.

    - We will work on electronics from other manufacturers as long as you are ok with the Mach3, Mach4 or LinuxCNC control software for your CNC machine or CNC router.

    - We will repair or retrofit used CNC electronics.

    - Some customers find that electronics are overwhelming to put together so we will finish these electronics wiring and assembly for you.

    The cost for these includes labor cost for the time it takes to finish the CNC electronics repair or retrofit and for any parts that need to be replaced or added.

    Here is an example of CNC electronics that we worked on for a customer:



    This is the type of response that you can expect to receive after the CNC electronics are repaired or retrofitted to work under Mach3, Mach4 or LinuxCNC. You can see the entire work, which also shows the time involved. We also show what we were able to accomplish at the beginning of the video.

    Click the link to respond:
    My electronics stopped working

  • I just bought a 3040 800 watt cnc. What electronics do i need to buy to run it?

    If you do not have electronics for your CNC, you will need stepper motors (or servos) that will fit your torque requirements, drivers for the motors, a power supply, applicable wires, and an interface board for computer communication. We sell electronic combo kits here https://buildyourcnc.com/electronicscombo.aspx

    Click the link to respond:
    I just bought a 3040 800 watt cnc. What electronics do i need to buy to run it?

  • Does your electronics combo allow 2 drivers on a single axis on the interface board?

    Yes, you can have two drivers connected to a single axis. If you want the two drivers/motors to work as a single, more concerted pair, then I would suggest connecting the two drivers to a single step pulse and direction signal.

    That is to say:
    driver 1 and driver 2 have wires connecting from the CP terminals of the drivers to a single step terminal on the interface board (USB or parallel breakout board), and the CW terminals of the drivers connected to a single direction terminal on the interface board.

    If the motors need to spin in the opposite directions, simply reverse one of the the motor A B coil connections (i.e. wires that would go to A+ and A- is connected to the B+ and B-, and the same with the B+ and B- to the A+ and A-). You can alternatively resolve this mechanically if desired.

    Click the link to respond:
    Does your electronics combo allow 2 drivers on a single axis on the interface board?

  • Just purchased the book "Build Your Own CNC Machine". Can I get hardware and electronics kits and how?

    The electronics (stepper motors, drivers, power supply and interface board) can be found here:
    https://www.buildyourcnc.com/item/electronicsAndMotors-3axis-425-elcombo

    If your computer cannot connect to the parallel breakout board (the interface card), just make sure to inform us that you need the USB alternative.

    Click the link to respond:
    Just purchased the book "Build Your Own CNC Machine". Can I get hardware and electronics kits and how?

  • I would like to use Mach3 instead of the software for my CNC router. Can you fix the electronics for me?

    Yes, you can send your electronics to us for repair, or retrofit to work with either Mach3, Mach4 or LinuxCNC. You can send us an email at customerService@buildyourcnc.com to set up your appointment.

    Some of the types of CNC electronics we will consider.

    - We will work on electronics from other manufacturers as long as you are ok with the Mach3, Mach4 or LinuxCNC control software for your CNC machine or CNC router.

    - We will repair or retrofit used CNC electronics.

    - Some customers find that electronics are overwhelming to put together so we will finish these electronics wiring and assembly for you.

    The cost for these includes labor cost for the time it takes to finish the CNC electronics repair or retrofit and for any parts that need to be replaced or added.

    Here is an example of CNC electronics that we worked on for a customer:



    This is the type of response that you can expect to receive after the CNC electronics are repaired or retrofitted to work under Mach3, Mach4 or LinuxCNC. You can see the entire work, which also shows the time involved. We also show what we were able to accomplish at the beginning of the video.

    Click the link to respond:
    I would like to use Mach3 instead of the software for my CNC router. Can you fix the electronics for me?

  • hi, what about, if I buy from you some elecronic parts like (3 Axis Electronics Combo) and I use them here in france , where the electric voltage is 220V 50Hertz ? thats gonna works? thanks

    Our electronics contains a switchable power supply that allows you to switch the input mains voltage between 115 volts (110/120) and 230 volts (220/240). the hertx range is not specified, but there are capacitors to smooth out standard frequencies to enable DC output.

    Click the link to respond:
    hi, what about, if I buy from you some elecronic parts like (3 Axis Electronics Combo) and I use them here in france , where the electric voltage is 220V 50Hertz ? thats gonna works? thanks

  • what do I need to hook up the electronics?

    Here is a list of the parts needed to get the electronics combo functioning (parallel or USB interface options):

    - 22 or 24 gauge stranded hookup wire to connect all of the drivers to the USB or parallel interface (terminal to terminal connections),
    - 18 gauge stranded hookup wire to connect the drivers to the power supply,
    - a power cable (extension cord) to connect from the power outlet to the power supply,
    - 4 conductor cable to connect the drivers to the stepper motors,
    - a USB cable to connect from the computer to the USB interface (or for power to the parallel interface),
    - for the parallel interface, a parallel cable is needed (male to male db-25),
    - a computer (for parallel interface, the computer will need a parallel port and if the computer does not contain a parallel interface, the motherboard may have a header for it, or you can purchase a parallel adapter to plug into the motherboard, very inexpensive),
    - cnc control software: for the USB interface, you will need planet-cnc software, for the parallel interface, you can use any industry standard cnc control software (the typical is Mach3 for Windows, or EMC2 or Linuxcnc for Linux (Linuxcnc.org).

    5v power supply is not needed. The 5 volts signal level power is derived from the computer through USB on both types of interfaces.

    Click the link to respond:
    what do I need to hook up the electronics?

Get Help with:
This Product
Orders
Tech Support
Sales
This Product
Order Query
Tech Support
Sales
Not logged in. Log In Register
Track Order(s)
View Order(s)
I Want to Schecule a One-On-One Paid Tech Support Session
Book an Appointment Pertaining to a BuildYourCNC Product (Free)
Ask a Quesion Below (Free):
Book an Appointment Pertaining Other Equipment ($60/half hour)
Book an Immedite Appointment Pertaining Other Equipment ($120/half hour)
Ask a Quesion Below (Free):
Waiting for response... I may not answer immediately, but I was notified on my cellular phone so my response is forthcoming. If I don't respond immediately, you can always go to the [My Account] page to see all of our chats at any time.