[ Log In ]
[ Register ]

Question #: 14813

Question: what shipper do you use?

Current Solution

The type of wire that should be used between the spindle and the VFD (Variable Frequency Driver also called the inverter) should be of stranded type and we use between 18 and 16 AWG.

The total current is divided among the three coil wires, therefor a wire gauge of 16 should be sufficient.

Currently we use 20AWG 4 conductor.

Additional Information:

Respond:

Other Possible Solutions to this Question

  • WHAT SETTINGS DO I USE IN MACH3 MOTOR TUNING?

    blueChick:

    X-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    blackToe:

    X-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    blackFoot:

    X-axis
    “CW8060 (6.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100 (“0”=down, “1”=up)
    Mach3 Motor Tuning: 914.29 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    greenBull:

    X-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/16 Microstep
    Dipswitches: 01100110 (“0”=down, “1”=up)
    Mach3 Motor Tuning: 914.29 steps/in

    Y-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/16 Microstep
    Dipswitches: 01100110
    Mach3 Motor Tuning: 914.29 steps/in

    Z-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/4 Microstep
    Dipswitches: 01100100
    Mach3 Motor Tuning: 1600 steps/in


    Scratch-Build / Book-Build Kit:

    X-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100 (“0”=down, “1”=up)
    Mach3 Motor Tuning: 1600 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    Additional Information:


    Additional Information:
    Scratch built/book CNC with NEMA 34 motors and CW8060 microstep driver

    Additional Information:

    Click the link to add information to this solution:
    WHAT SETTINGS DO I USE IN MACH3 MOTOR TUNING?

  • WHAT LENGTHS OF ROLLER CHAIN DO I USE FOR THE GREENBULL 4X CNC?

    The roller chain lengths for the greenBull 4x is:
    - 13 feet for each side of the X axis (total of 26 feet), and
    - 6 feet for the Y-axis

    Click the link to add information to this solution:
    WHAT LENGTHS OF ROLLER CHAIN DO I USE FOR THE GREENBULL 4X CNC?

  • WHAT ELECTRICAL CABLE DO I USE TO CONNECT VFD INVERTER SPINDLE?

    The type of wire that should be used between the spindle and the VFD (Variable Frequency Driver also called the inverter) should be of stranded type and we use between 18 and 16 AWG.

    The total current is divided among the three coil wires, therefor a wire gauge of 16 should be sufficient.

    Currently we use 20AWG 4 conductor.

    Additional Information:

    Click the link to add information to this solution:
    WHAT ELECTRICAL CABLE DO I USE TO CONNECT VFD INVERTER SPINDLE?

  • WHAT MOTORS DOES THE BLACK TOOTH USE?
  • WHAT DIPSWITCH SETTINGS SHOULD I USE?

    blueChick:

    X-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    blackToe:

    X-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    blackFoot:

    X-axis
    “CW8060 (6.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100 (“0”=down, “1”=up)
    Mach3 Motor Tuning: 914.29 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    greenBull:

    X-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/16 Microstep
    Dipswitches: 01100110 (“0”=down, “1”=up)
    Mach3 Motor Tuning: 914.29 steps/in

    Y-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/16 Microstep
    Dipswitches: 01100110
    Mach3 Motor Tuning: 914.29 steps/in

    Z-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/4 Microstep
    Dipswitches: 01100100
    Mach3 Motor Tuning: 1600 steps/in


    Scratch-Build / Book-Build Kit:

    X-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100 (“0”=down, “1”=up)
    Mach3 Motor Tuning: 1600 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    Additional Information:


    Additional Information:
    Scratch built/book CNC with NEMA 34 motors and CW8060 microstep driver

    Additional Information:

    Click the link to add information to this solution:
    WHAT DIPSWITCH SETTINGS SHOULD I USE?

  • WHAT MOTORS DOES THE BLACK TOOTH USE?
  • WHAT CAN CNC MACHINES DO?

    There is virtually no limit to what a CNC can do. CNC machines are responsible for almost all modern day machining operations in manufacturing industries. They normally costs tens of thousands of dollars, or hundreds of thousands of dollars. Our machines can be used to engrave plaques, cut wood for kits, mill aluminum parts, and inject plastic components. All it requires is willing to learn and understand how to use the machines to accomplish what you want to do.

    Additional Information:
    Curved Trophy

    Additional Information:

    Click the link to add information to this solution:
    WHAT CAN CNC MACHINES DO?

  • WHAT ELSE DO I NEED TO BUY?

    PC with parallel port and USB port
    20awg stranded wires for the motors - http://www.buildyourcnc.com/electronicscombo.aspx
    18awg stranded wires for power supply to drivers
    24awg stranded wires for breakout board to drivers
    (location and spacing of components varies from one person to another, so we do not provide cables/wires)
    - General purpose extension cord (cut the female end off) to provide power to power supply
    - USB cable to power breakout board
    - Parallel cable to communicate to breakout board
    - Router
    - (optional - instead of router) Spindle with power inverter http://www.buildyourcnc.com/SpindlesAndAccessories.aspx
    - (if purchasing spindle with inverter) General purpose extension cord (240v) (cut the female end off) to provide power to power inverter
    - End Mill(s) http://www.buildyourcnc.com/ProductsEndMills.aspx
    - CAD, and/or CAD-CAM software (to produce geometry, machine operations, and g-code) http://www.buildyourcnc.com/CNCsoftware.aspx
    - CNC control software (to read g-code and control machine) http://www.buildyourcnc.com/CNCsoftware.aspx
    - If the machine does not have the table included, then a table will need to be built. The rails, chain and chain mounts are included that are used on this table.

    Click the link to add information to this solution:
    WHAT ELSE DO I NEED TO BUY?

  • WHAT CABLE LENGTHS SHOULD USE FOR THE BLACKTOE

    The motor cables for the blackToe are as follows:

    Total 30 feet

    X - 9
    Y - 10
    Z - 11

    Click the link to add information to this solution:
    WHAT CABLE LENGTHS SHOULD USE FOR THE BLACKTOE

  • WHAT DO I SET FOR MY STEPS PER?

    blueChick:

    X-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    blackToe:

    X-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    blackFoot:

    X-axis
    “CW8060 (6.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100 (“0”=down, “1”=up)
    Mach3 Motor Tuning: 914.29 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    greenBull:

    X-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/16 Microstep
    Dipswitches: 01100110 (“0”=down, “1”=up)
    Mach3 Motor Tuning: 914.29 steps/in

    Y-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/16 Microstep
    Dipswitches: 01100110
    Mach3 Motor Tuning: 914.29 steps/in

    Z-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/4 Microstep
    Dipswitches: 01100100
    Mach3 Motor Tuning: 1600 steps/in


    Scratch-Build / Book-Build Kit:

    X-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100 (“0”=down, “1”=up)
    Mach3 Motor Tuning: 1600 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    Additional Information:


    Additional Information:
    Scratch built/book CNC with NEMA 34 motors and CW8060 microstep driver

    Additional Information:

    Click the link to add information to this solution:
    WHAT DO I SET FOR MY STEPS PER?

  • WHAT MACHINES DO WE SELL PLANS FOR

    Yes, the CNC machine hardware and plans combo is the same machine as in the book. The machine that we provide the plans for, can be found on the website, here http://buildyourcnc.com/Item/cnc-machine-scratchbuild

    Click the link to add information to this solution:
    WHAT MACHINES DO WE SELL PLANS FOR

  • WHAT ELSE DO I NEED WITH THE MACHINE?

    PC with parallel port and USB port
    20awg stranded wires for the motors - http://www.buildyourcnc.com/electronicscombo.aspx
    18awg stranded wires for power supply to drivers
    24awg stranded wires for breakout board to drivers
    (location and spacing of components varies from one person to another, so we do not provide cables/wires)
    - General purpose extension cord (cut the female end off) to provide power to power supply
    - USB cable to power breakout board
    - Parallel cable to communicate to breakout board
    - Router
    - (optional - instead of router) Spindle with power inverter http://www.buildyourcnc.com/SpindlesAndAccessories.aspx
    - (if purchasing spindle with inverter) General purpose extension cord (240v) (cut the female end off) to provide power to power inverter
    - End Mill(s) http://www.buildyourcnc.com/ProductsEndMills.aspx
    - CAD, and/or CAD-CAM software (to produce geometry, machine operations, and g-code) http://www.buildyourcnc.com/CNCsoftware.aspx
    - CNC control software (to read g-code and control machine) http://www.buildyourcnc.com/CNCsoftware.aspx
    - If the machine does not have the table included, then a table will need to be built. The rails, chain and chain mounts are included that are used on this table.

    Click the link to add information to this solution:
    WHAT ELSE DO I NEED WITH THE MACHINE?

  • WHAT ARE THE BEST FOODS THAT WILL HELP YOU LOSE WEIGHT?

    Lettuce, or any vegetable. Also drink a cup of water before meals, it'll make you feel fuller.

    Click the link to add information to this solution:
    WHAT ARE THE BEST FOODS THAT WILL HELP YOU LOSE WEIGHT?

  • WHAT CAUSES RINGING IN YOUR EAR AND HOW CAN YOU STOP IT?

    Tinnitus . Learn to love it. No really you should see a doctor. Make sure. White noise will help you sleep when it gets loud.

    Additional Information:
    I learned, too late, that if a sudden loud event causes tinnitus, see an audiologist IMMEDIATELY. They can do something about it if addressed within a day or so.

    Wear hearing protection...always. Loud noises trigger my tinnitus, and headphones and ear plugs (when out & about or at the movies, subway, etc) help tremendously. Mine are rated 33dB.

    Click the link to add information to this solution:
    WHAT CAUSES RINGING IN YOUR EAR AND HOW CAN YOU STOP IT?

  • THESE MACHINES ARE DANGEROUS, WHAT DO DO?

    These machines are inherently dangerous. Before the machine moves, the machine should be clear of any person by a dimension of at the distance of a persons reach plus a few more feet. This is the policies we institute in our shop and what is recommend to all of our customers. Treat these machines as you would treat any major power tool in the shop.

    With that said, you can certainly add some protective parts, but still keep folks away even with those installed. I would use the gantry side to do all of the mounting of the protective parts. Consider using sheet metal that you can bend and make a simple installation right on the gantry side.

    Click the link to add information to this solution:
    THESE MACHINES ARE DANGEROUS, WHAT DO DO?

  • DO YOU ACCEPT MASTERCARD?

    Yes, we accept standard credit cards on our shopping cart. All you need to do is enter the credit card information in the payment area.

    Click the link to add information to this solution:
    DO YOU ACCEPT MASTERCARD?

  • WHAT CABLE LENGTHS SHOULD USE FOR THE BLACKFOOT CNC MACHINE

    The blackfoot requires a total of 50 feet of cable.

    The X axis needs 15 feet
    The Y axis needs 17 feet
    and the Z-axis needs 18 feet

    These are 20 gauge 4 conductor cable.

    Click the link to add information to this solution:
    WHAT CABLE LENGTHS SHOULD USE FOR THE BLACKFOOT CNC MACHINE

  • IF I DON'T HAVE A PARALLEL PORT, WHAT DO DO?

    If your computer does not have a parallel port, all you will need is a low cost PCI parallel adapter card (these can be found on amazon for $15-$20). If you plan on using a laptop (not recommended) you can try to find a PCMCIA parallel adapter, but many people have frequent issues with this setup. A more expensive solution would be to purchase a USB smooth stepper board. Unfortunately, we do not supply any of these adapters and cannot attest to their reliability.

    Additional Information:
    ur gay

    Additional Information:

    Click the link to add information to this solution:
    IF I DON'T HAVE A PARALLEL PORT, WHAT DO DO?

  • DO YOU HAVE SECRETS?

    Yes, all of the answers I have that you cannot see are considered secrets!

    Click the link to add information to this solution:
    DO YOU HAVE SECRETS?

Get Help with:
This Product
Orders
Tech Support
Sales
This Product
Order Query
Tech Support
Sales
Not logged in. Log In Register
Track Order(s)
View Order(s)
I Want to Schecule a One-On-One Paid Tech Support Session
Book an Appointment Pertaining to a BuildYourCNC Product (Free)
Ask a Quesion Below (Free):
Book an Appointment Pertaining Other Equipment ($60/half hour)
Book an Immedite Appointment Pertaining Other Equipment ($120/half hour)
Ask a Quesion Below (Free):
Waiting for response... I may not answer immediately, but I was notified on my cellular phone so my response is forthcoming. If I don't respond immediately, you can always go to the [My Account] page to see all of our chats at any time.