The eyebolts are used in the squaring of the machine. I would use a standard carpenters square and first run the end mill along the edge of the square to first make it parallel with the long axis. Then run the end mill along the other edge with the short axis and adjust the eye bolts and chain according to the angle that the machine is out of square.

Additional Information:

Click the link to add information to this solution:
DO NEED TO SQUARE UP THE MACHINE AND IF SO YOU HAVE INSTRUCTIONS OR VIDEO FOR THIS?

You can find the wiring diagrams for the blackTooth on step 105 and 106 on the list of instructions on the blackTooth page. Step 105 pertains to the parallel breakout board and step 106 pertains to the USB interface board.

Additional Information:
wire size

Click the link to add information to this solution:
WHERE ARE THE WIRING DIAGRAMS FOR BLACKTOOTH LASER CUTTER IN INSTRUCTIONS?

I would recommend using our 5.6 amp driver as a replacement for the TX14207 driver. Apparently, those drivers are found in the 6040 CNC routers and will not contain documentation since it is typically sold as a part of a greater assembly. Here is the link to the recommended driver:
https://buildyourcnc.com/item/electronicsAndMotors-stepper-driver-6!0a

Click the link to add information to this solution:
Where can I get a motor driver "TX14207", or a substitute with instructions?

Which controller would you like to learn how to control a plasma cutter?

Additional Information:


Additional Information:
Bsmced4u-pp bitsensor.com

Additional Information:
Bsmced4u-pp bitsensor.com

Click the link to add information to this solution:
Please show how to setup all pins and ports to use output 1 to activate a relay for plasma.

What controller are you using?

Additional Information:

Click the link to add information to this solution:
Please show how to setup all pins and ports to use output 1 to activate a relay for plasma.

Which controller would you like to learn how to control a plasma cutter?

Additional Information:


Additional Information:
Bsmced4u-pp bitsensor.com

Additional Information:
Bsmced4u-pp bitsensor.com

Click the link to add information to this solution:
Please show how to setup all pins and ports to use output 1 to activate a relay for plasma.

The motor that is attached to the 4th axis is wired as follows:

The motor should have red, green yellow and blue wires coming form the motor. The red and green are paired as one coil and the yellow and blue is paired as the other coil. You can wire the motor to a 3.0 amp driver with red to A+, green to A-, Yellow to B+ and Blue to B-

Click the link to add information to this solution:
HOW DO I WIRE THE 4TH AXIS THAT YOU SELL. I HAVE MACH3 SOFTWARE. NO INSTRUCTIONS ON YOUR SITE

For both of the controllers that I recommend, the pokeys57CNC and the Mach3 USB controllers, will both work fine in windows 10. If you are using the Mach3 USB controller, confirm that the output in the ports and pins configuration is using port 3.

Click the link to add information to this solution:
output will not work in windows 10

The spindle does not come with a manual, however the inverter should come with a manual booklet in the box. The wiring diagram and PD settings for the inverter and spindle (https://www.buildyourcnc.com/item/spindle-inverter-2!2kw-spindle-novfd) can be view together on the spindle page, also you can use a local hardware store extension cord (orange) to connect/wire from your outlet(220V) to your inverter and spindle accordingly from the diagram.

Additional Information:
I also received a spindle and inverter without a manual. While the diagrams on the product page were sufficient to get the unit running, there is no documentation anywhere to be found concerning the terminal block that is used for external control. What does one have to do to get a hold of the manual that was supposed to come with the inverter? Manuals for the 220VAC model are plentiful online; however, manuals for the 110VAC model are non-existent.

Click the link to add information to this solution:
Transaction EQEPB4915043, My 2.2Kw Spindle and Inverter showed up without any manual or instructions. Can you provide a manual? Thank you

Make sure to watch my Mach3 USB outputs video on the product page for the Mach3 USB controller. If it still doesn't work, make sure to set the port to port 3 for the output you are using.

Click the link to add information to this solution:
mach 3 not activating output 1?

In the motor outputs, the spindle should be set to pin number 3. This is also the output terminal number 3 (O3). In Mach3: Select [Config], select [Ports and Pins], and select [Spindle Setup] page in the popup dialog box. In the Motor Control box, check Use Spindle Motor Output and select PWM Control.

[Use spindle motor output] is checked, Mach3 will automatically enable the spindle motor output pin. Click OK when the pop-up happens that will say "Spindle Motor has now been enabled. Ensure you set its pinouts.

Next, select the Motor Outputs tab. At the line where [Signal] is [Spindle], check [Enable], modify [Step Port] to "3", modify [Step Pin#] to "3", and specify O3 as Is the output terminal of the PWM.

Press [OK] button to save. Connect the indicator (refer to the previous section) to O3 for debugging. When the program "M3"executed is, O3 output signal can be seen.

The AVI+ and AVI- corresponds to the ACM and AVI terminals.

Additional Information:
In the answer setting, 0-24V is output to out3, but not to AVI+/ACOM.
Of course, 10V is given to the 10V terminal of the board.

Click the link to add information to this solution:
How to output 0-10V to AVI+AVI-?

U - Pin1
V - Pin2
W - Pin3
Pin4 Dead

Additional Information:
My home made cnc is a big problem with my NC connection. When in start my spindle it will be gone wrong. It will be limith switch problem anytime. Need help thanks.

Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
WHAT ARE THE OUTPUT INVERTER (VFD) CONNECTIONS TO SPINDLE?

Which controller would you like to learn how to control a plasma cutter?

Additional Information:


Additional Information:
Bsmced4u-pp bitsensor.com

Additional Information:
Bsmced4u-pp bitsensor.com

Click the link to add information to this solution:
when using mach3 how can I start the plasma using output signal at output 1?

Which controller would you like to learn how to control a plasma cutter?

Additional Information:


Additional Information:
Bsmced4u-pp bitsensor.com

Additional Information:
Bsmced4u-pp bitsensor.com

Click the link to add information to this solution:
when using mach3 how can I start the plasma using output signal at output 1?

Change PD001 Source of Run Commands to '1'
Change PD005 Max operating frequency to 400hz
Change PD004 base frequency to 400hz
Change PD003 Main frequency to 400hz
Change PD006 Intermediate frequency to 2.5
Change PD008 max voltage to 220v
Change PD009 Intermediate voltage to 15v
Change PD010 Min voltage to 8
Change PD011 frequency lower limit to >100hz (120hz to start)
Change PD142 7 Amps
Change PD143 2
Change PD144 3000

Note: PD001 had to be changed back to 0 to allow for keypad control.
Note2: I had to reverse U and V to get the spindle to go forward in FWD. (reverse any two wires, u&v or w&v for example)

Additional Information:

Click the link to add information to this solution:
HOW DO YOU SETUP THE SPINDLE INVERTER VFD?

Change PD001 Source of Run Commands to '1'
Change PD005 Max operating frequency to 400hz
Change PD004 base frequency to 400hz
Change PD003 Main frequency to 400hz
Change PD006 Intermediate frequency to 2.5
Change PD008 max voltage to 220v
Change PD009 Intermediate voltage to 15v
Change PD010 Min voltage to 8
Change PD011 frequency lower limit to >100hz (120hz to start)
Change PD142 7 Amps
Change PD143 2
Change PD144 3000

Note: PD001 had to be changed back to 0 to allow for keypad control.
Note2: I had to reverse U and V to get the spindle to go forward in FWD. (reverse any two wires, u&v or w&v for example)

Additional Information:

Click the link to add information to this solution:
HOW DO YOU SETUP THE SPINDLE INVERTER?

Yes, other CO2 laser tubes will work fine with our laser controller (including the Reci tube). Our laser controller is a digital based controller that controls the laser tube power supply, the motor drivers and other peripherals by outputting digital signals to these devices.

Laser controller URL:
https://www.buildyourcnc.com/item/Laser-Component-Laser-Control-System

Click the link to add information to this solution:
Can the laser controller work with higher output laser tubes, like 150W?

The parallel breakout board uses pins 10 to 13 relating specifically to the pin numbers on the parallel port. It is in fact 13 and not i3.

The mach3 USB board does use the I1-I4 using the I to represent the word "input"; hence I3 (i3).

Thanks for the question and wanting clarification.

Click the link to add information to this solution:
In the video 'Primer on Homing and the Use of Limit Switches' Patrick refers to pin number "13". Is this in fact pin "i3"?

Influenza is the most frequent cause of death from a vaccine-preventable disease in the United States. From 1990 through 1999, an average of approximately 36,000 influenza-associated pulmonary and circulatory deaths occurred during each influenza season. In addition to fatalities, seasonal influenza is also responsible for more than 200,000 hospitalizations per year. Rates of infection from seasonal influenza are highest among children, but the risks for complications, hospitalizations, and deaths are higher among adults ages 65 and older, children younger than 5 years, and people of any age who have medical conditions that place them at increased risk for complications from influenza.

A novel H1N1 virus was first detected in March of 2009 and quickly spread to pandemic levels. In the U.S., it is estimated that approximately 43-89 million persons became ill with 2009 pandemic H1N1 from April 2009 to April 2010. The virus also resulted in significant hospitalizations and deaths among children, adults 19-65 years, obese persons, and pregnant and post-partum women.

Click the link to add information to this solution:
HOW SERIOUS A PROBLEM INFLUENZA IN THE U.S.?