[ Log In ]
[ Register ]
NEW: CNC Router PLANS Available for all of our Newest CNC Models!! Click here to "Design Your CNC".

Question #: 155

Question: What are the dipswitch settings for the drivers?

Current Solution

blueChick:

X-axis
“CW230 (3.0A) Driver”
Set to 1/16 Microstep, 2.7A
Dipswitches: 11001100
Mach3 Motor Tuning: 1422.22 steps/in

Y-axis
“CW230 (3.0A) Driver”
Set to 1/16 Microstep, 2.7A
Dipswitches: 11001100
Mach3 Motor Tuning: 1422.22 steps/in

Z-axis
“CW230 (3.0A) Driver”
Set to 1/4 Microstep, 2.7A
Dipswitches: 10101100
Mach3 Motor Tuning: 1600 steps/in

blackToe:

X-axis
“CW230 (3.0A) Driver”
Set to 1/16 Microstep, 2.7A
Dipswitches: 11001100
Mach3 Motor Tuning: 1422.22 steps/in

Y-axis
“CW230 (3.0A) Driver”
Set to 1/16 Microstep, 2.7A
Dipswitches: 11001100
Mach3 Motor Tuning: 1422.22 steps/in

Z-axis
“CW230 (3.0A) Driver”
Set to 1/4 Microstep, 2.7A
Dipswitches: 10101100
Mach3 Motor Tuning: 1600 steps/in

blackFoot:

X-axis
“CW8060 (6.0A) Driver”
Set to 1/16 Microstep, 2.7A
Dipswitches: 11001100 (“0”=down, “1”=up)
Mach3 Motor Tuning: 914.29 steps/in

Y-axis
“CW230 (3.0A) Driver”
Set to 1/16 Microstep, 2.7A
Dipswitches: 11001100
Mach3 Motor Tuning: 1422.22 steps/in

Z-axis
“CW230 (3.0A) Driver”
Set to 1/4 Microstep, 2.7A
Dipswitches: 10101100
Mach3 Motor Tuning: 1600 steps/in

greenBull:

X-axis
“CW8060 (6.0A) Driver”
Set to 5.43A, 1/16 Microstep
Dipswitches: 01100110 (“0”=down, “1”=up)
Mach3 Motor Tuning: 914.29 steps/in

Y-axis
“CW8060 (6.0A) Driver”
Set to 5.43A, 1/16 Microstep
Dipswitches: 01100110
Mach3 Motor Tuning: 914.29 steps/in

Z-axis
“CW8060 (6.0A) Driver”
Set to 5.43A, 1/4 Microstep
Dipswitches: 01100100
Mach3 Motor Tuning: 1600 steps/in


Scratch-Build / Book-Build Kit:

X-axis
“CW230 (3.0A) Driver”
Set to 1/4 Microstep, 2.7A
Dipswitches: 10101100 (“0”=down, “1”=up)
Mach3 Motor Tuning: 1600 steps/in

Y-axis
“CW230 (3.0A) Driver”
Set to 1/4 Microstep, 2.7A
Dipswitches: 10101100
Mach3 Motor Tuning: 1600 steps/in

Z-axis
“CW230 (3.0A) Driver”
Set to 1/4 Microstep, 2.7A
Dipswitches: 10101100
Mach3 Motor Tuning: 1600 steps/in

Additional Information:


Additional Information:
Scratch built/book CNC with NEMA 34 motors and CW8060 microstep driver

Additional Information:

Respond:

Other Possible Solutions to this Question

  • What are the toggle switch settings on the stepper motor drivers for the .5 in. lead screw 10 tpi 2 turns per inch? Thankyou!

    On the top of the stepper motor drivers is a grid with the appropriate toggle switch positions for the lead screw being used. If it is 2 turns per inch, the proper toggle switch positions would be 01101110. Try this and see if it works.

    Click the link to respond:
    What are the toggle switch settings on the stepper motor drivers for the .5 in. lead screw 10 tpi 2 turns per inch? Thankyou!

  • WHAT DIPSWITCH SETTINGS SHOULD I USE?

    blueChick:

    X-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    blackToe:

    X-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    blackFoot:

    X-axis
    “CW8060 (6.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100 (“0”=down, “1”=up)
    Mach3 Motor Tuning: 914.29 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    greenBull:

    X-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/16 Microstep
    Dipswitches: 01100110 (“0”=down, “1”=up)
    Mach3 Motor Tuning: 914.29 steps/in

    Y-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/16 Microstep
    Dipswitches: 01100110
    Mach3 Motor Tuning: 914.29 steps/in

    Z-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/4 Microstep
    Dipswitches: 01100100
    Mach3 Motor Tuning: 1600 steps/in


    Scratch-Build / Book-Build Kit:

    X-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100 (“0”=down, “1”=up)
    Mach3 Motor Tuning: 1600 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    Additional Information:


    Additional Information:
    Scratch built/book CNC with NEMA 34 motors and CW8060 microstep driver

    Additional Information:

    Click the link to respond:
    WHAT DIPSWITCH SETTINGS SHOULD I USE?

  • I'm building my own machine using your motors and drivers. What is the best dip switch settings for the 3.0 amp drivers powering the 425 oz motors

    The settings that you will use for your 3.0 amp driver to properly power and turn your 425 oz-in stepper motor will cheifly depend on your application and the mechanical parts you are using on your machine. In all circumstances, the amp setting for the stepper motor (according to the datasheet) should be 2.8 amps. Use the closest setting on the driver without going over.

    Here is a good rule of thumb for the microstepping which will correspond to the resolution, but wil also affect torque. You always want to try to achieve the best torque and resolution for the axis you are moving but go with the lowest microstepping possible. In cases where there is mechanical advantage, like a lead screw scenario, where for each motor revolution, the axis move a very small amount, you will want a very low microstep value. This is because the mechanical configuration will provide most of the finer resolution and you will not need the microstepping to assist in this. Increase the microstepping only in conditions where the axis is not moving smooth enough, or where there is a mechanical disadvantage. A mechanical disadvantage would be where the stepper motor is causing a great amount of movement in the axis and the resolutions suffers from this condition. Increase the microstep value up to your desired resolution, but don't go over since the torque of the motor will decrease.

    Click the link to respond:
    I'm building my own machine using your motors and drivers. What is the best dip switch settings for the 3.0 amp drivers powering the 425 oz motors

  • what are all the settings i'd need for mach3 for use with a blackfoot and a redfly?

    These are the recommend values(default) for our blackFoot CNC machine, the acceleration and velocity can be adjusted as high as the motor can rotate without stalling! Suggested increment's will be by 10's.

    blackFoot:
    X-axis
    “CW8060 (6.0A) Driver”
    Set to 1/16 Microstep, 5.43A
    Dipswitches: 01100110 (“0”=down, “1”=up)
    Mach3 Motor Tuning: 914.29 steps/in, Velocity 400.02, Acceleration 4
    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in, Velocity 400.02, Acceleration 4
    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in, Velocity 79.98, Acceleration 5

    Additional Information:
    how can we tuning the CNC motor

    Click the link to respond:
    what are all the settings i'd need for mach3 for use with a blackfoot and a redfly?

  • What settings does I use for controlling the spindle in StepCon/Linuxcnc?

    LinuxCNC has excellent documents; however, I would like to offer our help in case you don't understand the information on that page. So, please use this FAQ (Question #: 13233) to state your questions by submitting additional information below.

    The LinuxCNC spindle control page is found here: http://linuxcnc.org/docs/html/examples/spindle.html

    Additional Information:
    After reading the LinuxCNC page my first questions would be can the spindle be controlled by PWM signal? Also, what pin on the parallel port would I set to Spindle Enable and FRW?

    Additional Information:
    To connect your computer to the VFD, use a USB to RS-485 interface. RS-485 is just a serial interface protocol that uses standard 0 to +5 voltage TTL signal levels for communication (as opposed to RS-232 which uses -12v and +12 for signal level changes).

    Get a high quality interface to reduce any issues during the process. The VFD should have two terminals labeled RS+ and RS-. The USB to RS-485 adapter should have this labeled on it as well so the connections should be relatively straight forward.

    In the VFD parameters:
    PD001: 2 to accept RS485 commands
    PD002: 2 to accept frequency comands
    PD163: 1 to RS485 slave address:1
    PD164: 1 RS485 baud rate 9600
    PD165: 3 8bit, no parity, 1 stop bit

    Make sure LinuxCNC is also set accordingly:

    The PIN14 and PIN16 in the stepconf wizard should be set to unused because you don't want LinuxCNC to be outputting unnecessary signals.

    In the options step of the stepconf wizard:
    - Check the Include Halui user interface component.
    - Check the Include custom PyVCP GUI panel.
    - Check Spindle speed display

    You will want to edit the custom.hal text file located in the folder that was created from the stepconf wizard. Add these following lines:
    loadusr -Wn vfd hy_vfd -n vfd -d /dev/ttyUSB0 -p none -r 9600
    net spindle-cmd-rpm-abs => vfd.speed-command
    net spindle-cw motion.spindle-forward => vfd.spindle-forward
    net spindle-ccw motion.spindle-reverse => vfd.spindle-reverse
    net on motion.spindle-on => vfd.spindle-on

    The dev folder in linux is typically used for interfacing devices and peripherals to the computer as these devices are communicated by simple memory addresses and these files are linked directly to these addresses.

    Under the custom_postgui.hal file, change this line:

    from: sets spindle-at-speed true
    to: net spindle-at-speed => cfd.spindle_at_speed

    and add the line:

    setp vfd.enable 1

    When you start LinuxCNC, you will a spindle section with the reverse and forward buttons, a stop button and - and + buttons. Use these buttons to conform that the spindle is functioning properly. The spindle speed indicator in LinuxCNC will show the spindle speed and you can confirm that this is equal to the speed indicated on the VFD.


    Credit for this helpful information goes to:


    Additional information was also added by us to provide a better understanding.

    Click the link to respond:
    What settings does I use for controlling the spindle in StepCon/Linuxcnc?

  • What are the fault conditions of the DM556 and DM542 drivers?

    There are three main LED fault signals that the DM556 and DM442 drivers exhibit. There is a red and green LED. The red LED will show the fault signals.

    The fault signals are:

    - Over-Current: If there is continuous current that is above 16 amps, the Red LED will flash every three seconds. Over-current could be related to: a short in the motor coils, or two of the wires of the motor are shorted; of the motor wires/coil is shorted to ground.

    - Over-voltage: If the power supply output to the driver exceeds a voltage of 52 volts, the red LED will flash twice every three seconds.

    - Phase Error: Is the motor wires are not connect, or they are connected incorrectly, the red LED will flash four times every three seconds.

    Click the link to respond:
    What are the fault conditions of the DM556 and DM542 drivers?

  • My question about motor tuning for the blacktoe in Mach 3 was for the aceleration and velocity settings what are the recomended settings

    In the customer service live, just enter "motor tuning" and it will give you a list of all the recommended or default settings for our machines. However the acceleration and velocity for the greenBull(other machines) will be an actual determination on your trials. You will want the highest possible acceleration and velocity without the motors stalling, so you can do increments of ten to be on the safe side, if it is too slow try increments of 25.

    The steps per inch is dependent on the microstepping:
    Steps/Inch for the x and y
    Steps = 200 motor steps per revolution x 16 microsteps = 3200 steps
    Inches = sprocket number of teeth x pitch of the sprocket = 14 x .25" = 3.5 inches
    steps/inch = 3200 / 3.5 = 914.28
    This is really a starting point. You will then need to use the mach3 calibration function to get the perfect steps/inch value. Use as long a measurement as possible when calibrating.

    Velocity:
    Start with a value of 1000 ipm. Increase this value with a relatively low acceleration at about 10. You will notice at a particular velocity that it will stall. This is your stall velocity. I would take the stall velocity and reduce it by about 30% to 50% which should give you a good final safe velocity.

    Acceleration:
    Once the velocity is found, raise the acceleration until it start to stall at a low velocity. Reduce the acceleration by about the same percentage to stick with a safe acceleration.

    The acceleration is mostly dependent on torque (current) and the top speed is dependent on the amount of voltage.

    Give some tests with all of the axes running at the same time. If you notice and stalling, reduce velocities and acceleration depending on when the stall happens (top end, or acceleration curve).


    X-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/16 Microstep
    Dipswitches: 01100110 (“0”=down, “1”=up)
    Mach3 Motor Tuning: 914.29 steps/in
    Y-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/16 Microstep
    Dipswitches: 01100110
    Mach3 Motor Tuning: 914.29 steps/in
    Z-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/4 Microstep
    Dipswitches: 01100100
    Mach3 Motor Tuning: 1600 steps/in

    Additional Information:


    Additional Information:


    Additional Information:
    4th axis


    Additional Information:

    Click the link to respond:
    My question about motor tuning for the blacktoe in Mach 3 was for the aceleration and velocity settings what are the recomended settings

  • Please share what versions of ReplicatorG, Python, Java, Firmware and the Arduino drivers you are currently using for the whiteAnt 3d printer.

    We use the version 0024 of replicatorG which works quite well. The firmware is specified on the videos as you perform the installation. You can find the videos on this page: https://www.buildyourcnc.com/whiteAnt3DPrinterandCNCMachine.aspx

    Click the link to respond:
    Please share what versions of ReplicatorG, Python, Java, Firmware and the Arduino drivers you are currently using for the whiteAnt 3d printer.

  • what is microstepping concerning the drivers

    Stepper motors are designed to move in specific increments; these increments are called "steps". For example, a common standard is for 200 steps per full revolution. Microstepping is a method to send signals to the motor to move only a fraction of a full step at a time. For example, if a motor has 200 steps per revolution and is microstepped 1/16, then effectively there are 3200 small step movements (microsteps) per revolution instead of 200 larger ones. This makes the motion of the motor much smoother and more precisely controllable, at the cost of decreased holding torque.

    Here are is a good references for stepper motor theory: http://users.ece.utexas.edu/~valvano/Datasheets/StepperMicrostep.pdf

    And Wikipedia has a good overview as well:
    https://en.wikipedia.org/wiki/Stepper_motor

    Additional Information:


    Additional Information:
    Therefore, the difference in 128th and 64th microstepping is increased resolution and smoothness for 128th microstepping, at the cost of decreased holding torque.

    Click the link to respond:
    what is microstepping concerning the drivers

  • What are the overall dimensions of the 2.5A small stepper drivers? Is there a CAD model available?

    The overall dimensions of our 2.5 modular stepper divers is:

    L: 1.875"/ 47.625mm
    W: 1.433"/ 36.3982mm
    H: .585"/ 14.859mm (height might change due to different terminal block height (other we have on hand is .464"/ 11.7856mm))

    Currently we do not have a CAD model on hand.

    Click the link to respond:
    What are the overall dimensions of the 2.5A small stepper drivers? Is there a CAD model available?

  • Do you know what drivers the xylotex control boxes have

    After looking at their site, we cannot determine what drivers are used in the xylotex control box.

    Click the link to respond:
    Do you know what drivers the xylotex control boxes have

  • WHAT CABLE LENGTHS ARE USED FOR THE BLACKTOE

    The motor cables for the blackToe are as follows:

    Total 30 feet

    X - 9
    Y - 10
    Z - 11

    Click the link to respond:
    WHAT CABLE LENGTHS ARE USED FOR THE BLACKTOE

  • WHAT ARE THE DIMENSIONS FOR GREENBULL TABLE?

    Actual table dimension: 4'x8' is 56.078"x 121.50" (the overhang in the illustrations should be 3/4" thick)
    To determine the frame dimensions, first consider using the frame height shown of almost 3' (2.86'). The width of the frame should be 4" narrower than the dimension from rail edge to rail edge (6X rail to rail is 80.078"). This will provide a 2" overhang on both sides (4X frame width should be 56.078").
    The length of the frame should be 4" shorter than the desired length of the rails to provide a 2" overhang on both ends. The travel length will be 20" shorter than the rail length due to the space occupied by the gantry sides.
    Two long pieces of 3/4" material will need to be placed on top of the frame with the 2" overhang on the sides and the end. These long strips of material will receive the rails and the chain mounts on the ends.


    Link:
    https://www.buildyourcnc.com/Item/cnc-machine-greenBull-v4-4X

    Click the link to respond:
    WHAT ARE THE DIMENSIONS FOR GREENBULL TABLE?

  • what are the motor setting for the greenbull

    In the customer service live, just enter "motor tuning" and it will give you a list of all the recommended or default settings for our machines. However the acceleration and velocity for the greenBull(other machines) will be an actual determination on your trials. You will want the highest possible acceleration and velocity without the motors stalling, so you can do increments of ten to be on the safe side, if it is too slow try increments of 25.

    The steps per inch is dependent on the microstepping:
    Steps/Inch for the x and y
    Steps = 200 motor steps per revolution x 16 microsteps = 3200 steps
    Inches = sprocket number of teeth x pitch of the sprocket = 14 x .25" = 3.5 inches
    steps/inch = 3200 / 3.5 = 914.28
    This is really a starting point. You will then need to use the mach3 calibration function to get the perfect steps/inch value. Use as long a measurement as possible when calibrating.

    Velocity:
    Start with a value of 1000 ipm. Increase this value with a relatively low acceleration at about 10. You will notice at a particular velocity that it will stall. This is your stall velocity. I would take the stall velocity and reduce it by about 30% to 50% which should give you a good final safe velocity.

    Acceleration:
    Once the velocity is found, raise the acceleration until it start to stall at a low velocity. Reduce the acceleration by about the same percentage to stick with a safe acceleration.

    The acceleration is mostly dependent on torque (current) and the top speed is dependent on the amount of voltage.

    Give some tests with all of the axes running at the same time. If you notice and stalling, reduce velocities and acceleration depending on when the stall happens (top end, or acceleration curve).


    X-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/16 Microstep
    Dipswitches: 01100110 (“0”=down, “1”=up)
    Mach3 Motor Tuning: 914.29 steps/in
    Y-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/16 Microstep
    Dipswitches: 01100110
    Mach3 Motor Tuning: 914.29 steps/in
    Z-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/4 Microstep
    Dipswitches: 01100100
    Mach3 Motor Tuning: 1600 steps/in

    Additional Information:


    Additional Information:


    Additional Information:
    4th axis


    Additional Information:

    Click the link to respond:
    what are the motor setting for the greenbull

  • what is the price for Planet-CNC software?

    The base price for planet cnc is 69 Euros, which translates to $85.85 dollars. Can be found here (http://www.planet-cnc.com/index.php?page=shop)

    Additional Information:


    Additional Information:

    Click the link to respond:
    what is the price for Planet-CNC software?

  • WHAT ARE THE SHIPPING DIMENSIONS FOR GREENBULL?

    76" X 40" X 26"
    230 LBS

    Click the link to respond:
    WHAT ARE THE SHIPPING DIMENSIONS FOR GREENBULL?

  • WHAT ARE THE CABLE LENGTHS FOR BLACKTOE

    The motor cables for the blackToe are as follows:

    Total 30 feet

    X - 9
    Y - 10
    Z - 11

    Click the link to respond:
    WHAT ARE THE CABLE LENGTHS FOR BLACKTOE

  • WHAT ARE THE CABLE LENGTHS FOR BLACKTOE

    The motor cables for the blackToe are as follows:

    Total 30 feet

    X - 9
    Y - 10
    Z - 11

    Click the link to respond:
    WHAT ARE THE CABLE LENGTHS FOR BLACKTOE

  • what are the exchage rates for europe?

    The best way to find the exchange rates for Europe is to google "exchange rates for europe":
    https://www.google.com/webhp?sourceid=chrome-instant&ion=1&espv=2&es_th=1&ie=UTF-8#q=exchange+rates+for+europe&spell=1

    Click the link to respond:
    what are the exchage rates for europe?