Mach 3 is compatible with our electronic combo's that include the Parallel Breakout Board.
Planet-CNC is compatible with our electronic combo's that included our USB Breakout Board.

The parallel breakout board is compatible to a wide variety of software control packages. The USB interface board that we sell can only be used with the Planet-cnc control software.

If you are concerned with your computer (desktop) not having a parallel port, one can be purchased and inserted into a PCI slot on the motherboard. Some motherboard also come with a parallel port header (connector) on the motherboard and a simple cable can be connected to this connector to get that functionality on the computer. The former solution of getting a parallel port adapter card to plug into the motherboard is probable the easiest and least expensive option.

Additional Information:


Additional Information:
Is the mach 3 software compatible with kollmorgen s200 servo motors and controllers?

Click the link to add information to this solution:
IS THE MACH3 SOFTWARE COMPATIBLE WITH 3 AXIS MOTION CONTROL COMBO KITS? PLANET CNC MENTIONED AS BEING COMPATIBLE.

Everyone always assumes they are doing something wrong when a plant fails to perform to their expectations. Grapes need pollinator activity to set viable fruit, but there is a shortage of bee activity throughout the country. When the flower cannot be pollinated by bees, the resulting fruit usually atrophies. It is not your fault, just a shortcoming in nature's network.

Click the link to add information to this solution:
I PLANTED SEVERAL CONCORD GRAPE VINES DURING THE PAST FEW YEARS. GOT A COUPLE OF VERY TINY BUDS THIS YEAR, BUT THEY DRIED UP AND DIED. WHAT AM DOING WRONG?

Portable cell phones emit about 0.6 watts of radiofrequency energy, limited primarily by the power of the battery. As with any radiofrequency transmitter, there will be some amount of absorption in the human body; the amount depends on how close you are to the antenna. The Federal Communications Commission (FCC) limits the amount of radiofrequency energy which cell phones can deposit in the body to levels at which no health effects are to be expected. See an article on Cell Phone Safety on this website for more information.

Gary H. Zeman, ScD, CHP

Click the link to add information to this solution:
HOW MUCH RADIATION GIVEN OFF BY A CELL PHONE AND THERE ANY WAY TO STOP THE FROM BEING ABSORBED INTO YOURSELF?

Yes, all of the spindles come with collets. The collets have a 1/4" (6.35mm) bore for end mills that have a 1/4" shank. The ER specification is different for the 1.5kW (ER-11) and the 2.2kW (ER-20).

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
I’M LOOKING TO PURCHASE SPINDLE AND VFD WAS CURIOS IF THE SPINDLES COME WITH COLLETS SO WHICH ONES?

Yes Mach3 is a great program. Our 3 axis is 6'X12'X3'using all BYCNC components (incl. redsprout)

Click the link to add information to this solution:
I JUST BOUGHT THE 3 AXIS W/HEAVY GANTRY, WILL MACH 4 RUN WELL WITH THIS, AND HOW LARGE CAN GO CUT AREA

The blackTooth Laser cutter and Engraver can be built in a weekend. Take a look at the build instructions and try to determine if you feel you have sufficient capability to put together the laser system.

Click the link to add information to this solution:
HOW COMPLEX IS YOUR KIT TO ASSEMBLE, AND MOST IMPORTANTLY - HARD IT SETUP CONTROL THE LASER WITH MACH3?

These machines are inherently dangerous. Before the machine moves, the machine should be clear of any person by a dimension of at the distance of a persons reach plus a few more feet. This is the policies we institute in our shop and what is recommend to all of our customers. Treat these machines as you would treat any major power tool in the shop.

With that said, you can certainly add some protective parts, but still keep folks away even with those installed. I would use the gantry side to do all of the mounting of the protective parts. Consider using sheet metal that you can bend and make a simple installation right on the gantry side.

Additional Information:

Click the link to add information to this solution:
THE CNC MACHINE IS UNSAFE WITH EXPOSED SPROCKETS THAT CAN DAMAGE FINGERS AND HAVE CLOTHING CAUGHT IN IT.

Yes, you can use the video tutorial on the website. Here is a link: http://www.buildyourcnc.com/CNCElectronicsandWiring.aspx

Click the link to add information to this solution:
ARE THERE STILL VIDEOS THAT CAN WATCH AS PUT THIS TOGETHER, I'LL BUY THEM IF HAVE TO, VERY FUSTURATED WITH ELECTROCTICS AND WIRING PART.

The parts list is located on this page: http://buildyourcnc.com/cnckitintro.aspx at the bottom of the description.

Additional Information:



Additional Information:

Click the link to add information to this solution:
DOES YOUR COMBO #1 WITH PLANS AND THE DVD COME COMPLETE PARTS LIST?

BYCNC Response:
The book build was intended to be 20 inches x 40 inches. Larger machines were designed after the book build was introduced so customers would have the option to go bigger than what the book offered. Check out our larger machines on the website as the machines sizes range from 1 foot x 3 feet all the way up to 6 feet x 12+ feet.

User Response:
I'm not wanting to spend $3,000+ on a machine, I want to build one that will do a 4x8 sheet of wood. Will the plans in the book scale up?

BYCNC Response:
It is possible to scale the book build up, but the rigidity of the gantry would be questionable at that span, even if the height of the gantry structure were to be increased. The gantry design would need to be modified to become a box shape rather than a flat configuration. The kits on the site were design for those wanting a larger machine.

Click the link to add information to this solution:
I BOUGHT YOUR BOOK AND WAS HOPEING IT HAD PLANS OR DIMENTIONS ON HOW TO BUILD A CNC HOLD 4X8 SHEET OF PLY. WILL THE IN SCALE UP?

Yes and properly soldered.

Additional Information:
20

Click the link to add information to this solution:
DO YOU SUPPLY THE MALE PORTION OF MOTOR CONTROL CABLES WITH REDLEAF?

The eyebolts are used in the squaring of the machine. I would use a standard carpenters square and first run the end mill along the edge of the square to first make it parallel with the long axis. Then run the end mill along the other edge with the short axis and adjust the eye bolts and chain according to the angle that the machine is out of square.

Additional Information:

Click the link to add information to this solution:
DO NEED TO SQUARE UP THE MACHINE AND IF SO YOU HAVE INSTRUCTIONS OR VIDEO FOR THIS?

There are several CAD/CAM programs out there for MacOS. Here is a list of a few: http://www.macuser.de/forum/f53/3d-2d-cad-395058/#post4499316
I've also read good things about punchCAD: http://www.punchcad.com/
Of course, there is always SketchUp if you are in a pinch. There are a few CAM plugins for SketchUp as well, but I've never used them, so I can't vouch for them.

CAD/CAM will get you as far as designing your parts and producing the g-code, but if you also want to run the CNC machine with your Mac, you will need a piece of software similar to Mach3 or EMC to run the g-code. I haven't been able to find anything like these programs that runs on Mac, so you may have to run Mach3 or EMC in Windows using Boot Camp or a virtual machine such as VMware or Parallels.

Personally, I would use the Mac to do all the CAD/CAM, then use a cheap PC to run the CNC machine.

Additional Information:


Additional Information:
EasyDNC for OSX
www.dnc-x.com

Additional Information:


Additional Information:
Hi guys I’m new to the cnc and I’m beginning to learn how to operate and cad-cam software also my cnc runs on Mach3 my questions is if I should use MacBook to do all designs if I can have all this software to run on Mac or I have to use windows software to operate it? I have separate small computer connected to the cnc table who have Mach3 on it please help. Also if you know any other software much easy for beginners please let me know thank you guys!
My email if needed is r1jastrzebski@gmail.com

Additional Information:


Additional Information:
Hi , thank you for your advise!

Additional Information:
Hi , thank you for your advise!

Additional Information:
Hi , thank you for your advise!

Additional Information:
Hi , thank you for your advise!

Additional Information:

Click the link to add information to this solution:
DOES ANY OF THE SOFTWARE THAT COMES WITH IT COMPATIBLE MAC 10.6?

Does your breakout board (interface) have a relay? If so, you can connect one of the router/spindle's ac lines through the relay. The M3, M4 and M5 codes are used to control the router/spindle. Typically, the M codes are automatically added to the g-code regardless if you configure this in your CAM software. If you have the breakout board from buildyourcnc, you can go to the product page for the breakout board and the relay connection diagram and narrative is in the instructions on that page.

Click the link to add information to this solution:
WHAT IS THE MOST EASY WAY TO HOOK UP MILL IN THAT AUTOMATICALLY STARTS WHEN CYCLE STARTS, AND STOPS GCODE THROUGH?

Depending if the spindle can work with this specific VFD, it might be possible. However we would not like to risk you working unit, with a possible match so we would like more details on your specific model and any information available on the spindle itself.

Response
The only info on the spindle is 2.2KW 400HZ 220V. Made by Zhong Hua Jiang.

Was originally on a Delta C200 vfd. That is 220 single phase.

Click the link to add information to this solution:
I PURCHASED A VFD AND SPINDLE FROM FRIEND, HIS SET UP IS 220. DON'T HAVE 220 IN MY SHOP. QUESTION CAN USE YOUR 110 WITH THIS SPINDLE??

If your motors are hot to the touch, this is normal. Current is being drawn by the motor coils as the motor moves and as the motor stays at a position. If the motor is not using the current in the coils to move (holding it's position), the energy will be translated as heat (rather than motion, sound or light). Even while moving, some of the energy will be lost as heat. Remember that energy cannot be created nor destroyed.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
I HAVE FOLLOWED ALL THE "CNC ELECTRONICS 1 - 9" VIDEOS AND I'M USING ALMOST EXACT SAME COMPONENTS (MOTORS RUN SOUND GOOD) BUT MOTORS ARE RUNING VERY HOT IN JUST 15MIN WITH NO LOAD DONE SOMETHING WRONG OR DO STEPPERS HOT?

Yes. You are referring to Afluria, which is manufactured in Australia by CSL Laboratories for the U.S. market. CSL's 2010 Southern Hemisphere influenza vaccine (Fluvax and Fluvax Junior) has been associated with increased post-marketing reports of fever and febrile seizures in children predominantly younger than age 5 years as compared to previous years. For this reason, on August 5, 2010, ACIP recommended that Afluria, 0.5 mL, licensed for use in people age 36 months and older, not be used in children younger than age 9 years. ACIP further recommended that Afluria could be administered to children ages 5 through 8 years who are at high risk for influenza complications if there is no other age-appropriate TIV available, after risks and benefits of using this vaccine in this age group have been discussed with the parent or guardian. The vaccine should not be given to children younger than age 5 years. For detailed information, go to www.cdc.gov/media/pressrel/2010/s100806.htm.

Click the link to add information to this solution:
WE'VE HEARD THAT ACIP HAS LIMITED THE USE OF ONE INFLUENZA VACCINE PRODUCTS FOR CHILDREN BEGINNING WITH 2010-11 VACCINATION SEASON. TRUE?

If you would like to use a spindle rather than a router on your existing CNC, we will send you another set of components that will allow the spindle to be mounted properly which includes the z-axis rails, rail support, spindle mounts and the dust shoe components. You can find this item to purchase here: https://www.buildyourcnc.com/category/z-axis

Click the link to add information to this solution:
I HAVE BLACKTOE 4.1 WITH PORTER CABLE 890 ROUTER.TO CONVERT TO SPINDLE(2.2KW) CAN JUST CHANGE THE MOUNT?

If your computer does not have a parallel port, all you will need is a low cost PCI parallel adapter card (these can be found on amazon for $15-$20). If you plan on using a laptop (not recommended) you can try to find a PCMCIA parallel adapter, but many people have frequent issues with this setup. A more expensive solution would be to purchase a USB smooth stepper board. Unfortunately, we do not supply any of these adapters and cannot attest to their reliability.

Additional Information:
ur gay

Additional Information:

Click the link to add information to this solution:
MY COMPUTER DOES NOT HAVE A PARALLEL PORT. HOW DO I INTERFACE WITH THE BREAKOUT BOARD?