We currently do not sell any plan's for any of our machines, only for our scratch and build kit.

Click the link to add information to this solution:
Would you sell a kit that has all of the hardware and electronics with CNC plans for the table and gantry? Some of have access to a CNC temporarily (TechShop) but want one of our own.

If your bearing does not turn anymore, it is possible to repair the frozen bearing.

You can carefully remove the shield on one side of the bearing. Use a very thin blade to remove the shield.

Once the shield is removed, use WD-40 or kerosene to wash out and clean any debris that exists within the bearing. WD-40 is a cleaner, not a lubrication agent.

You will then need to re-lubricate the bearing. Packing grease into the bearing will provide good protection not allowing too much metal on metal friction. There will be a layer of grease separating the ball bearings from the inner and outer races.

If you have a production environment, you may want to purchase extra bearings so that you will not have any down time.

If you have a rubber shield, just pry it out using any sharp object, like a utility knife. If your bearing has a metal shield, there may be a retaining ring along the outer race keeping the shield in place. Simply remove the retaining ring and the metal shield will fall out easily. If the metal shield does not have a retaining ring, that shield will not be able to be removed and a new bearing will need to be purchased to replace the frozen bearing.

Click the link to add information to this solution:
You built the first 36 inch Blue Chick for me. One of the V-Groove bearings on the X-axis froze. Is there a method of repairing this? Or do I order another and a spare. If so, what is the procedure to repair or order?

The leadscrew length for the greenBull long Z-axis is 47 inches.

Additional Information:

Click the link to add information to this solution:
BUILDING ONE OF YOUR GREENBULL 6X LONG AND 2.2 KILOWATT SPINDLE DOES NOT FIT. SEEMS LEAD SCREW YOU SENT WITH KIT IS SHORT 42" LOOKS LIKE IT NEEDS TO BE 5 OR 6 INCH LONGER. THIS CORRECT? WHAT THE NEEDED LENGTH FOR UNIT?

The leadscrew length for the greenBull long Z-axis is 47 inches.

Additional Information:

Click the link to add information to this solution:
Building one of your greenBull 6X Long and 2.2 kilowatt spindle does not fit. Seems lead screw you sent with kit is short 42" looks like it needs to be 5 or 6 inch longer. Is this correct? What is the needed length of lead screw for this unit?

We don't hold those boards in-house anymore. You can use the schematic to form your own boards if you wish.

Additional Information:
Thanks for the reply. Has this proven to be a good design?

Additional Information:

Click the link to add information to this solution:
Regarding L6203/L297 Stepper Board Driver, would you be willing to sell two unpopulated boards? A friend and I are each building a low cost CNC and I already have most of the components. Thanks.

it is possible to install 2 motors on a single axis but you will require another driver and motor, but wire it directly to the same pins on your breakout board. Also the orientation of your motor since it is opposite side of the original so getting it to move accordingly to the original motor it will need to be orientated correctly. The slight shift could be the cause of the rod not being completely flat where the set screws are suppose to tighten the sprocket to the rod, so sanding it to a flatter surface might fix the shift in directions.
Currently do not have a kit or schematic available.

Click the link to add information to this solution:
I am interested in your Black Toe (24" X 48") machine, and am wondering if using two medium motors on the "X" and "Y" axis makes sense relative to power and alignment (racking). What would you recommend?

I would suggest using the NPN proximity sensor for the Mach3 USB or the Pokeys57cnc. The proximity sensors have a top DC voltage limit of 30 volts, so it would be best to use the 24V power supply that is used to power the controller. Both controllers have a 24V power requirement, so that is convenient.

The blue wire of the proximity sensor is the GND wire and is connected to the 24V power supply's V- terminal. The brown wire is the positive wire and is connected to the V+ terminal of the 24V power supply. The black wire is the signal wire and is connected to the input terminal of the controller.

Click the link to add information to this solution:
Good evening, if I wanted to use your inductive proximity sensor's with your USB interface board what would I need besides the sensors I would be using 5 of the sensors. I have a 48V 12amp power supply. Thank you

Currently our only location is in Katy, Texas at this current time, we can help you assemble the machine and if any issues occur we can always help you with the problems, but will have to be managed through email or phone (which ever is your preference).

Click the link to add information to this solution:
I live in China and my company would like to buy the 40w laser cutting machine. I am wondering if you can help us assemble and maintain the machine in China? Do you have any service point here? Thank you

All of our CNC machines can carve at that depth without a problem and do 3d carving. Our typical application is cutting sheet materials, but a good percentage of our customers cut 3D bas reliefs or even more complex 3D objects using reference points and jigs.

Most of our CNC machines have a Z travel of at least 6 inches for the smaller machines and 7 to 10 inches for our larger machines. The Fabricator Pro has a Z travel of 10 inches.

Depending on your application, you will need to consider the length of the end mill (more than the deepest depth of the 3D carving) and the stock that you will be using. If the stock plus the length of the end mill exceed the clearance with the Z axis raised to the top extent, then you will need to consider the way the table/bed of the machine is formed (maybe with a depression to take advantage of the greater need for clearance).

The greenBull has the capability of Z axis travel of up to 36 inches, but I would recommend, if milling wood, that the Z-axis not extend more than 12 inches to reduce deflection.

Additional Information:
Most of the CAM software on the market will have 3D profile machining operation capabilities. CAMBAM has a very nice 3D prpfiling feature. The Vectric line of software can definitely handle this as well.

Click the link to add information to this solution:
All of the pics and videos show your cncs cutting sheet materials, I'm interested in carving 3d images in plastic and hardwood slabs up to 2" thick. What machine and software would you recommend?

If you would like to come to the office, please call the office at 281-815-7701 to request a visit at your specified time within our business hours so we can make sure that the right person will be there to assist you.

Click the link to add information to this solution:
I am considering the purchase of a Black foot or Green Bull CNC router and would like to come and visit your facility to see them in person and to discuss my requirements. Please can you tell me your address. I am based in NW Houston. Many thanks.

That will depend on the controller that was installed in the redFly. If the controller is a pokeys57CNC controller, you can use Mach 4 with that system.

You can add a 4th axis and an ATC (Automatic Tool Changer) with the redFly system.

Click the link to add information to this solution:
Does the Redfly that I bought with the GreenBull in 2016 work with Mach4? Also I want to add a 4th axis and a spindle with automatic tool changer. Will this work too or do I need a new control board? I bought my CNC with a longer Z travel, so I have plenty of room for these. Thanks!

Considering enlarging the machine, might have its down sides do to the structural integrity of the scratch build machine. Primarily by making the width longer it will start to sag in the center, which will lead to having to redesign the gantry to be more structurally rigid to support the added length. Which then will increase the weight and height of your gantry to support the add size, which will always end up to creating a larger CNC.

We usually do not recommend modifying the scratch build CNC, due to the very limited capabilities, and the structural design of the scratch build. We also do not recommend using longer than 48" ACME screw/leadscrew due to the increasing chance of warping and bending in the ACME screws/leadscrew in the given length.
We do recommend modifying the CNC machines we sell to accommodate the added requests that some of our customers desire, but you will be limited to the width of the gantry with our machines.

Click the link to add information to this solution:
I've read your book and I'm looking to purchase the hardware kit with DVD as well as an electronics kit. I would like my machine to have a working area of at least 24" wide by 48" long. Can I just make the bed (and gantry) wider to accommodate larger priceslike 30"x60"? If so what electronics kit would you recommend?

Yes, I was intending to design a medium sized laser cutter and engraver but the project was put on hold. I will start the design in a few weeks (around mid Dec 2017).

Additional Information:
Do you think you would want a horizontal machine, or a slanted, more vertically oriented machine?

Additional Information:
For the work I plan to do, I would need a horizontal bed. I will be doing some work with cutting small pieces and can not afford to have any drop during a raster or another vector cut.

Additional Information:
Ok. Thanks.

Click the link to add information to this solution:
Can you design and sell a laser that is medium sized? The Black Tooth is too small and the XL is too big. I need about 36" x 24" cutting space minimum. 60x40 is ideal.

Identify the Control Signals: First, determine which control signals from the DB25 interface card are used for spindle speed control. Typically, these are PWM (Pulse Width Modulation) signals or analog voltage signals.

VFD Configuration: Your VFD should be configured to accept the type of control signal your DB25 card provides. This involves setting parameters in the VFD that correspond to the type of input signal it will receive for speed control.

Wiring: Connect the appropriate output pins from the DB25 card to the input terminals on the VFD. This usually involves connecting the PWM or analog output to the corresponding input on the VFD. Make sure to consult the manuals for both your VFD and interface card for specific wiring details.

UCCNC Settings: Configure UCCNC to output the correct type of signal (PWM or analog) that matches your VFD's configuration. This is done through the software's spindle setup section.

Test and Adjust: Run some tests to ensure that the spindle speed is being correctly controlled by UCCNC. You might need to tweak settings in either the VFD or UCCNC for optimal performance.

Click the link to add information to this solution:
I am looking at purchasing your 2.2 kw water cooled spindle. I'm assuming it comes with the VFD. I have a rotary phase converter in my shop. Are these spindles 3 phase? And if so, can I bypass use of the VFD and control the spindle speed by the CAM software instead? Or is the VFD an absolute necessity to use on the spindle?

Yes, we have cut many fabrics with the laser. Or CO2 lasers can generally cut fabrics and textiles without a problem. What types of textiles (materials) do you need to use with the laser machine? Is there a layering of materials?

Additional Information:
We would cut multiple heights of different carpets and even hard surfaces such as Vinyl composition tile, Luxury vinyl tile,etc. and I'm wanting to explore etching into plain color carpets using the laser.
I'm contemplating your 5' x 12' machine with the laser/spindle combo.
Is it possible to make a site visit to your location and see the capabilities of the equipment ?

Additional Information:
Carpets are not a problem as long as there are no materials in the carpet or in the carpet binding layers that will off-gas toxic fumes. Check the manufacturer's materials of all of the parts of the carpet.

The vinyl should not be a problem, just make sure there is no material mixed within the composite that will off-gas harmful fumes such as chloride. The chloride will mix with the hydrogen in the air and form HCL (hydrochloric acid) which can be harmful if inhaled, but can also affect some of the metallic parts in the machine.

We have cut vinyl with the laser with great results.

Click the link to add information to this solution:
I own a custom rug shop where we design a fabricate custom floors of many types, Have you performed any type of testing using your 40 watt and or 80 watt laser for the cutting of thse textiles.

You can do raster and vector engraving on the greenBull laser/spindle combination. The methods of this process is not accomplished in the same way as the typical laser machines where CorelDRAW is used. The Mach3 laser plug-in can be used for the raster engraving and standard CNC g-code can be used for vector cutting and engraving.

The raster method will not be fast on the greenBull since the z-axis is heavy and there are inertial limitation on doing fast raster back and forth movement. Vector is the best use of this machine.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
I am looking at purchasing the greenbull 5X system with the laser/spindle combination. Can the laser do both rastered engraving as well as vectored cutting with the same breakout board and software? If I have this wrong please let me know what would be needed to accompish this.

You will find a blackToe USB version on the product page:

https://www.buildyourcnc.com/Item/cnc-machine-blacktoe-v4-2x4

Click the link to add information to this solution:
Looking to buy a black toe 2x4, what electronics are included ? Is it optional with USB-interface? And for last do you ship to sweden?

Currently we do not have that modification kit, our set up is fixed for our greenBull only modification kit we have for this model is the long z-axis kit(Designed for Foam cutting).

Click the link to add information to this solution:
I am building your "Green Bull' 6 foot wide kit and I am at the stage of attaching the motor and drive chain. I would like to know if you have an modification kit available to put the 1/2" ACME screw on the Y-axis?

You can always come to our offices in Katy TX. If that is not an option, we can do cut in our shop and record video for you. Specify what you would like to cut and we can consider doing this for you.

Thanks. I've reviewed the gallery and think my question comes down to this- Can I do hardwood carving like Mike M.'s guitar display cases and cut 3/4 inch baltic birch plywood with the same machine?

Absolutely, the cutting and machining is more a function of how the machining operations are created and specified. Baltic birch is not a tough material and you will be able to cut very aggressively with any of our machine kits.

Click the link to add information to this solution:
Where is the best place to see projects made with BuildYourCNC CNCs? I would like to get an idea of carving capabilities and cutting Baltic Birch plywood. Thanks.