We don't have cad models of the HIWIN blocks, but you can find the models on McMaster.com. They have can drawings and models for most of these types of parts.

Click the link to add information to this solution:
DO YOU HAVE CAD AVAILABLE FOR THE HIWIN GUIDE BLOCKS SELL AND RAIL?

We don't have cad models of the HIWIN blocks, but you can find the models on McMaster.com. They have can drawings and models for most of these types of parts.

Click the link to add information to this solution:
DO YOU HAVE CAD AVAILABLE FOR THE HIWIN GUIDE BLOCKS SELL AND RAIL?

The motor that is attached to the 4th axis is wired as follows:

The motor should have red, green yellow and blue wires coming form the motor. The red and green are paired as one coil and the yellow and blue is paired as the other coil. You can wire the motor to a 3.0 amp driver with red to A+, green to A-, Yellow to B+ and Blue to B-

Click the link to add information to this solution:
HOW DO I WIRE THE 4TH AXIS THAT YOU SELL. I HAVE MACH3 SOFTWARE. NO INSTRUCTIONS ON YOUR SITE

Yes, the CNC machine hardware and plans combo is the same machine as in the book. The machine that we provide the plans for, can be found on the website, here http://buildyourcnc.com/Item/cnc-machine-scratchbuild

Additional Information:



Additional Information:

Click the link to add information to this solution:
WHAT MACHINES DO WE SELL PLANS FOR

Thanks for the kind words. The kit is available for those that want the parts to assemble the case which comes with the computer parts. If you don't need the computer parts, let me know and I will offer the bare bones without the computer system.

Previous Solution:
I already have a DIY CNC machine with all my electronics but I have two cases the size of a mid tower PC and was looking to shrink the weight and footprint of all of them. I understand if you don't have plans available, I just really loved the design and compactness of your case.

Previous Solution:
The redLeaf and redSprout boxes are meant to provide enclosure to the systems that we assemble in-house for customers that prefer a complete plug and play system. We provide the kit of parts for the enclosure from overwhelming customer request. There are no plans available for the enclosure and the complexity of the parts needed to be fabricated is quite high where the task of cutting out all of the intricate parts by hand would be a larger investment in time and materials than the cost to purchase the kit.

Additional Information:
Just curious at what you would sell the box itself empty or the dimension files for the box for?

Additional Information:



Additional Information:

Click the link to add information to this solution:
DO YOU GIVE AWAY THE PLANS FOR REDLEAF/REDSPROUT BOX?

Thanks for the kind words. The kit is available for those that want the parts to assemble the case which comes with the computer parts. If you don't need the computer parts, let me know and I will offer the bare bones without the computer system.

Previous Solution:
I already have a DIY CNC machine with all my electronics but I have two cases the size of a mid tower PC and was looking to shrink the weight and footprint of all of them. I understand if you don't have plans available, I just really loved the design and compactness of your case.

Previous Solution:
The redLeaf and redSprout boxes are meant to provide enclosure to the systems that we assemble in-house for customers that prefer a complete plug and play system. We provide the kit of parts for the enclosure from overwhelming customer request. There are no plans available for the enclosure and the complexity of the parts needed to be fabricated is quite high where the task of cutting out all of the intricate parts by hand would be a larger investment in time and materials than the cost to purchase the kit.

Additional Information:
Just curious at what you would sell the box itself empty or the dimension files for the box for?

Additional Information:



Additional Information:

Click the link to add information to this solution:
DO YOU GIVE AWAY THE PLANS FOR REDLEAF/REDSPROUT BOX?

We do have a relay board that words like a standard relay.

Here is the URL of the relay board that we offer:

https://www.buildyourcnc.com/item/electronicsAndMotors-breakout-Relays-relay-board-250V-12A-5V

Click the link to add information to this solution:
I HAVE YOUR MACH3 USB BOB, DO YOU GUYS SELL A TORCH CONTROL RELAY CAN WIRE UP TO TURN MY PLASMA ON AND OFF HOW WOULD WIFE THAT TOO THIS BOB?

We just don't make enough on our machines to justify any discounts. We try to offer everyone the same low price.

If I can help in another way, please let me know.

Click the link to add information to this solution:
DO YOU HAVE SPECIAL DEALS FOR HACKERSPACES OR NON-PROFIT ORGANIZATIONS?

Tinnitus . Learn to love it. No really you should see a doctor. Make sure. White noise will help you sleep when it gets loud.

Additional Information:
I learned, too late, that if a sudden loud event causes tinnitus, see an audiologist IMMEDIATELY. They can do something about it if addressed within a day or so.

Wear hearing protection...always. Loud noises trigger my tinnitus, and headphones and ear plugs (when out & about or at the movies, subway, etc) help tremendously. Mine are rated 33dB.

Click the link to add information to this solution:
WHAT CAUSES RINGING IN YOUR EAR AND HOW CAN YOU STOP IT?

Yes you can. We well the ArtCAM software and modules.

Click the link to add information to this solution:
I SEE ARTCAM MODULES ON YOUR SITE, CAN STILL GET THEM THROUGH YOU?

The eyebolts are used in the squaring of the machine. I would use a standard carpenters square and first run the end mill along the edge of the square to first make it parallel with the long axis. Then run the end mill along the other edge with the short axis and adjust the eye bolts and chain according to the angle that the machine is out of square.

Additional Information:

Click the link to add information to this solution:
DO NEED TO SQUARE UP THE MACHINE AND IF SO YOU HAVE INSTRUCTIONS OR VIDEO FOR THIS?

No. In general, registration is voluntary. Copyright exists from the moment the work is created. You will have to register, however, if you wish to bring a lawsuit for infringement of a U.S. work.

Click the link to add information to this solution:
DO I HAVE TO REGISTER WITH YOUR OFFICE BE PROTECTED?

The hub length of the drive sprocket and the other mechanical devise that is used to connect on the shaft will determine the length of the shaft needed for use with the drive sprocket.

The hub lengths for our drive sprockets are 1/2". So if you are connecting the drive sprocket to a motor, your motor shaft will need to be at least 1/2" in length.

Click the link to add information to this solution:
wHAT IS THE SMALLEST LENGTH SHAFT I CAN USE FOR YOUR #25 DRIVE SPROCET?

U - Pin1
V - Pin2
W - Pin3
Pin4 Dead

Additional Information:
My home made cnc is a big problem with my NC connection. When in start my spindle it will be gone wrong. It will be limith switch problem anytime. Need help thanks.

Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
HOW DO YOU HOOK UP THE VFD TO SPINDLE?

Input to VFD:
240V Active - R
240V Neutral - S
Ground - E

Additional Information:

Click the link to add information to this solution:
HOW DO YOU CONNECT THE INVERTER TO AC?

Change PD001 Source of Run Commands to '1'
Change PD005 Max operating frequency to 400hz
Change PD004 base frequency to 400hz
Change PD003 Main frequency to 400hz
Change PD006 Intermediate frequency to 2.5
Change PD008 max voltage to 220v
Change PD009 Intermediate voltage to 15v
Change PD010 Min voltage to 8
Change PD011 frequency lower limit to >100hz (120hz to start)
Change PD142 7 Amps
Change PD143 2
Change PD144 3000

Note: PD001 had to be changed back to 0 to allow for keypad control.
Note2: I had to reverse U and V to get the spindle to go forward in FWD. (reverse any two wires, u&v or w&v for example)

Additional Information:

Click the link to add information to this solution:
HOW DO YOU SETUP THE SPINDLE INVERTER?

Limit switches are not really needed for this level of a machine, but if you do want to use them, then you will need to connect them with shielded cable and ground the shield at both ends and any other non-used wire in the cable. Limit switches are very susceptible to the motor interference. You will also need to adjust the debounce in the software you will use.

Click the link to add information to this solution:
DO NEED LIMIT SWITCHES, IF SO WHAT IS YOUR RECOMMENDATION?

Yes, we have the optional table for the blackToe, but we need to fabricate it, which only takes one day. We generally reserve one week for the total fabrication and packing of all parts.

Click the link to add information to this solution:
DO YOU HAVE BLACKTOES WITH TABLES?

Change PD001 Source of Run Commands to '1'
Change PD005 Max operating frequency to 400hz
Change PD004 base frequency to 400hz
Change PD003 Main frequency to 400hz
Change PD006 Intermediate frequency to 2.5
Change PD008 max voltage to 220v
Change PD009 Intermediate voltage to 15v
Change PD010 Min voltage to 8
Change PD011 frequency lower limit to >100hz (120hz to start)
Change PD142 7 Amps
Change PD143 2
Change PD144 3000

Note: PD001 had to be changed back to 0 to allow for keypad control.
Note2: I had to reverse U and V to get the spindle to go forward in FWD. (reverse any two wires, u&v or w&v for example)

Additional Information:

Click the link to add information to this solution:
HOW DO YOU SETUP THE SPINDLE INVERTER VFD?