[ Log In ]
[ Register ]

Question #: 2221

Question: Will the greenBull be able to cut seaboard materials?

Current Solution

The greenBull can cut HDPE Seaboard, and other materials as well. The machine will be cutting with either a router/spindle(customer preference) and will be the greatest aspect of actual cutting of material, to get a good overall coverage of materials. Our 2.2kW spindle will be the best option for a large variety of materials.

Respond:

Other Possible Solutions to this Question

  • CAN THE GREENBULL CUT 18MM BIRCH IN ONE PASS?

    If you use the 2.2kW spindle, it can cut at 3/4 inch or 19 mm deep with at least a 1/4" cutting diameter single flute end mill. You will get better results with larger diameter end mills, but that is the worst case scenario. I still recommend doing a finishing pass on the edge to make sure everything is perfect.

    Click the link to add information to this solution:
    CAN THE GREENBULL CUT 18MM BIRCH IN ONE PASS?

  • WHAT DOES THE GREENBULL KIT INCLUDE AND DO I NEED TO INCLUDE?

    The greenBull 4X comes with all of the components and electronics to assemble the gantry of the machine. You will need to build the table. We provide the rails and roller chain for the X-axis (along the length of the table for full 8 feet of travel). You will need to provide some wire to connect the electronics and a computer to run the machine. You will also need to purchase the software that you will need to run the machine that matches how you will apply the machine. We suggest the mach3 control program. The CAM program is up to you as there are many options out there.

    Click the link to add information to this solution:
    WHAT DOES THE GREENBULL KIT INCLUDE AND DO I NEED TO INCLUDE?

  • WHICH MACHINE SHOULD I BUY, THE GREENBULL OR BLACKFOOT?

    The greenBull can range is routing width sizes of 5 feet and 6 feet. The blackFoot has a 4 foot routing width.

    Previous Solution:
    The greenBull machine has a sturdier gantry than the blackFoot, so you can be more agressive with the cutting feedrate (cutting speed). The blackFoot is also a good machine, but it all comes down to the speed at which you want to produce the fabrication

    The spindle is also highly recommended for it's quietness and easier cleanup (no fan blowing the dust in the air)

    Click the link to add information to this solution:
    WHICH MACHINE SHOULD I BUY, THE GREENBULL OR BLACKFOOT?

  • SHOULD I SELECT THE GREENBULL OR BLACKFOOT CNC MACHINE?

    The greenBull can range is routing width sizes of 5 feet and 6 feet. The blackFoot has a 4 foot routing width.

    Previous Solution:
    The greenBull machine has a sturdier gantry than the blackFoot, so you can be more agressive with the cutting feedrate (cutting speed). The blackFoot is also a good machine, but it all comes down to the speed at which you want to produce the fabrication

    The spindle is also highly recommended for it's quietness and easier cleanup (no fan blowing the dust in the air)

    Click the link to add information to this solution:
    SHOULD I SELECT THE GREENBULL OR BLACKFOOT CNC MACHINE?

  • WHAT ARE THE SHIPPING DIMENSIONS FOR GREENBULL?

    76" X 40" X 26"
    230 LBS

    Click the link to add information to this solution:
    WHAT ARE THE SHIPPING DIMENSIONS FOR GREENBULL?

  • WHAT ARE THE DIMENSIONS FOR GREENBULL TABLE?

    Actual table dimension: 4'x8' is 56.078"x 121.50" (the overhang in the illustrations should be 3/4" thick)
    To determine the frame dimensions, first consider using the frame height shown of almost 3' (2.86'). The width of the frame should be 4" narrower than the dimension from rail edge to rail edge (6X rail to rail is 80.078"). This will provide a 2" overhang on both sides (4X frame width should be 56.078").
    The length of the frame should be 4" shorter than the desired length of the rails to provide a 2" overhang on both ends. The travel length will be 20" shorter than the rail length due to the space occupied by the gantry sides.
    Two long pieces of 3/4" material will need to be placed on top of the frame with the 2" overhang on the sides and the end. These long strips of material will receive the rails and the chain mounts on the ends.


    Link:
    https://www.buildyourcnc.com/Item/cnc-machine-greenBull-v4-4X

    Click the link to add information to this solution:
    WHAT ARE THE DIMENSIONS FOR GREENBULL TABLE?

  • IF I PURCHASE A GREENBULL 6X LONG Z CNC MACHINE KIT AND MACH3, WHAT ELSE WOULD BE REQUIRED TO ASSEMBLE THE WORKING MACHINE? HAVE CAD SOFTWARE.

    You will need to build the table unit for your machine. There are instructions on how to do this at the bottom of the product page here, https://www.buildyourcnc.com/Item/cnc-machine-blackFoot-v4
    There is no estimate on how much this will cost though, since there are too many variables involved to do this.

    - PC with parallel port and USB port
    - 20awg stranded wires for the motors - http://www.buildyourcnc.com/electronicscombo.aspx
    - 18awg stranded wires for power supply to drivers
    - 24awg stranded wires for breakout board to drivers
    (location and spacing of components varies from one person to another, so we do not provide cables/wires)
    - General purpose extension cord (cut the female end off) to provide power to power supply
    - USB cable to power breakout board
    - Parallel cable to communicate to breakout board
    - Router
    - (optional - instead of router) Spindle with power inverter http://www.buildyourcnc.com/SpindlesAndAccessories.aspx
    - (if purchasing spindle with inverter) General purpose extension cord (240v) (cut the female end off) to provide power to power inverter
    - End Mill(s) http://www.buildyourcnc.com/ProductsEndMills.aspx
    - CAD, and/or CAD-CAM software (to produce geometry, machine operations, and g-code) http://www.buildyourcnc.com/CNCsoftware.aspx
    - CNC control software (to read g-code and control machine) http://www.buildyourcnc.com/CNCsoftware.aspx

    This answer is applicable to most of our machines with the exception of the greenLean and the blueChick since those machines are equipped with a table structure.

    Click the link to add information to this solution:
    IF I PURCHASE A GREENBULL 6X LONG Z CNC MACHINE KIT AND MACH3, WHAT ELSE WOULD BE REQUIRED TO ASSEMBLE THE WORKING MACHINE? HAVE CAD SOFTWARE.

  • WHICH MACHINE SHOULD I BUY, GREENBULL OR BLACKFOOT?

    The greenBull can range is routing width sizes of 5 feet and 6 feet. The blackFoot has a 4 foot routing width.

    Previous Solution:
    The greenBull machine has a sturdier gantry than the blackFoot, so you can be more agressive with the cutting feedrate (cutting speed). The blackFoot is also a good machine, but it all comes down to the speed at which you want to produce the fabrication

    The spindle is also highly recommended for it's quietness and easier cleanup (no fan blowing the dust in the air)

    Click the link to add information to this solution:
    WHICH MACHINE SHOULD I BUY, GREENBULL OR BLACKFOOT?

  • WHAT KIND OF MATERIALS CAN MACHINE?

    There are almost no limits to the kind of materials you can machine. Anything from wood or plastic to exotic materials like stainless steel can be cut as long as the part can be safely and firmly held and the proper cutting tool and cutting speed are used

    Click the link to add information to this solution:
    WHAT KIND OF MATERIALS CAN MACHINE?

  • GREENBULL 5X10 X AXIS SHUTTERS

    If your axis shutters and will not move unless moved by another force, that sounds like your acceleration is set too high. Lower the acceleration until it works well, then lower it a bit more to have a margin of safety.

    Users response:
    I've lowered my acceleration to 1 in the StepCon program and it still shutters when I jog it, anything else I could check?

    Buildyourcnc response:
    IF that didn't work, try swapping the X and Y drivers. That way you will pinpoint if the issue is the driver. If the proplem persists, then there may be an issue with the motor itself.

    Buildyourcnc response:
    The X and Y drivers can be easily swapped by swapping only the motor wires.

    - Remove the x-axis motor wires from the X driver.
    - Remove the Y motor wires from the Y driver.
    - Insert the X motor wires into the Y driver.
    - Insert the Y motor wires into the X driver.

    Buildyourcnc response:
    Now the Y-axis will move the gantry. Test the Gantry movement by moving the Y axis using the up and down arrow keys (mach3).

    Users response:
    Problem is now solved, I switched the X and Y at the redFly and got the same problem, so then I undid the wires going to each motor and switched them there and it I had a bad solder point in the X axis connector, thank you for the help

    Buildyourcnc response:
    You're very welcome. We will make sure to thoroughly check the solder points on the cable connectors prior to a redFly delivery.

    Click the link to add information to this solution:
    GREENBULL 5X10 X AXIS SHUTTERS

  • GREENBULL BRUSH STRIP LENGTH

    The brush strip for a 7518 router specifically for a GreenBull is 18 3/4" inches in length.

    Click the link to add information to this solution:
    GREENBULL BRUSH STRIP LENGTH

  • GREENBULL 6X SILICON TUBING

    The greenBull 6X, uses a total of 52 Ft, of silicon tubing 1/4" ID - 3/8" OD. One way uses 26 Ft.

    Click the link to add information to this solution:
    GREENBULL 6X SILICON TUBING

  • GREENBULL 5X CABLE LENGTH

    The total cable length for a greenBull 5x is 50 ft. Now the individual cable lengths for the axis, is x=15 ft, y=17 ft, z=18 ft.

    Click the link to add information to this solution:
    GREENBULL 5X CABLE LENGTH

  • I JUST BOUGHT THE 3 AXIS W/HEAVY GANTRY, WILL MACH 4 RUN WELL WITH THIS, AND HOW LARGE CAN GO CUT AREA

    Yes Mach3 is a great program. Our 3 axis is 6'X12'X3'using all BYCNC components (incl. redsprout)

    Click the link to add information to this solution:
    I JUST BOUGHT THE 3 AXIS W/HEAVY GANTRY, WILL MACH 4 RUN WELL WITH THIS, AND HOW LARGE CAN GO CUT AREA

  • WHAT WOULD BE THE COST OF FREIGHT TO SOUTH AUSTRALIA?

    You can determine if the country is serviceable by:
    - selecting the items you want to purchase on the website
    - go to the cart (shopping cart top left of any webpage)
    - log in, or register
    - Enter the address and click on calculate shipping.

    The webpage will return the direct rates and whether your area is serviced or not. Feel free to enter any address as long as you are able to receive the package from that address.

    The shipping times are determined by the service you select in the shopping cart. If a machine is purchased, we generally have a one week lead time unless otherwise stated in the description of the machine's product page.

    Click the link to add information to this solution:
    WHAT WOULD BE THE COST OF FREIGHT TO SOUTH AUSTRALIA?

  • WILL THE LASER ENGRAVER WORK ON NON-ANODIZED ALUMINUM

    no, it will only work on anodized aluminum

    Click the link to add information to this solution:
    WILL THE LASER ENGRAVER WORK ON NON-ANODIZED ALUMINUM

  • WHAT ARE THE BEST FOODS THAT WILL HELP YOU LOSE WEIGHT?

    Lettuce, or any vegetable. Also drink a cup of water before meals, it'll make you feel fuller.

    Click the link to add information to this solution:
    WHAT ARE THE BEST FOODS THAT WILL HELP YOU LOSE WEIGHT?

  • CAN .7MM END MILL BE USED TO CUT THROUGH 15MM MDF?

    An end mill smaller than 1.5mm or 1/6" is too small a diameter for end mills to cut through materials that are thick. A good rule of thumb is if the end mill has a cutting length that is more than what you want to cut, that diameter will be acceptable.

    Click the link to add information to this solution:
    CAN .7MM END MILL BE USED TO CUT THROUGH 15MM MDF?

  • WILL CELL PHONES SPARK A FIRE AT THE GAS STATION?

    I can't think of any reason that it would be dangerous. However, I checked with the Cellular Telecommunications Industry Association. The Chairman of the Association sent the following memo on 18 June 1999, to the Associations' Board of Directors and others:
    "You may have received inquiries about wireless phones causing fires or explosions at gas stations. In particular, you may have been asked about an alleged explosion at a gas station in Indonesia. We have been unable to verify any such occurrence in Indonesia or anywhere else. Moreover, in our discussions with Shell Oil they have stated they have attempted to verify these reports and also have not been able to document any such occurrence."
    Nonetheless, in an abundance of caution, some manufacturers have included language in the owner's manuals for their products that recommends wireless phone users turn off their phones while at refueling points (gas stations). In addition, we have received information that Exxon will begin issuing warning signs at all domestic gas stations advising drivers to turn off all wireless communications devices when entering Exxon gas stations.

    While wireless phone owners should always consult their owner's manual for information on the use of the phone, we are not aware of any incident that would justify these concerns."

    Gen Roessler, Editor
    HPS website

    Click the link to add information to this solution:
    WILL CELL PHONES SPARK A FIRE AT THE GAS STATION?

Get Help with:
This Product
Orders
Tech Support
Sales
This Product
Order Query
Tech Support
Sales
Not logged in. Log In Register
Track Order(s)
View Order(s)
I Want to Schecule a One-On-One Paid Tech Support Session
Book an Appointment Pertaining to a BuildYourCNC Product (Free)
Ask a Quesion Below (Free):
Book an Appointment Pertaining Other Equipment ($60/half hour)
Book an Immedite Appointment Pertaining Other Equipment ($120/half hour)
Ask a Quesion Below (Free):
Waiting for response... I may not answer immediately, but I was notified on my cellular phone so my response is forthcoming. If I don't respond immediately, you can always go to the [My Account] page to see all of our chats at any time.