If you select the Settings Page and select or tick Auto Limit Override - this will allow you to back off the switch.

Additional Information:
limit and home switch

Click the link to add information to this solution:
When the machine hits the limits it stops but the switch is still tripped so clicking the Mach3 RESET button doesn't do anything. How am I supposed to get the machine to move off of the limit switch so I can continue working?

No, we have gotten away from the planet-cnc boards as they have decided to not support our board with their software. You can use the Mach3 USB board as an alternative. You will be better off with Mach3 as a control software as this is widely used and supported.

Mach3 USB board:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Click the link to add information to this solution:
I have the older discontinued USB breakout board. The y-axis no longer works and have traced it to the breakout board. Is there a replacement board that can use the same Planet CNC software running on Windows 10?

The port used with the Mach3 USB controller is Port 3. The pin associated with the input you are using matches the input terminal you are using. For instance, if you are using IN2, the pin number is 2.

Click the link to add information to this solution:
What is the correct pin and port setting for auto tool zero on the Mach3 USB interface board. the auto tool macro works but does not stop lowering the bit when it touches the touch plate. It does not blink the digitizer button in the diagnostic menu when the circuit is completed.

Yes, the Mach3 USB board has two terminals that require 24V connection. Most VFDs have a 24V output that can be used to power this part of the Mach3 USB board.

The V+ and V- on the Mach3 USB is not absolutely necessary to operate the CNC machine/router. The V+ and V- of the Mach3 USB board powers the outputs, inputs, and spindle's speed and control.

Here is the Mach3 USB link for more information:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

The new YL600 VFD we have in stock may not have this 24V output. There is a 12V terminal, but I have not tested that terminal if it outputs 12V, or if it is a 12V input. If you are only conecting limit switches to the Mach3 USB and need to power that portion, 12V will be sufficient.

I will delve into these aspects in far more detail on video.

Thanks and Merry Christmas to you as well!

Click the link to add information to this solution:
Hey Guys, I have a brand new redleaf and 5x. In the final stages of wiring and wondering a few things. Can I connect the Mach3 USB board V+ V- to my frequency inverter (type YL600-2s-2k20)? If so where? Will your upcoming (part 2)video deal with this as well as final connections for limit switches and stop button? Merry Christmas!

Sure, the USB interface has a place for 4 axes of limit switches.

Each axis can have two limit switches: one for the ++ (positive) end and one for the -- (negative) end. The positive end would be the limit switch at the end of the machine that, say the machine has a 4'x8' area, reaches a bit after the 8 foot mark. The negative end would be the limit switch behind the 0 foot location behind the origin. If the origin is in the middle, the negative would be at a little more than the -4 foot end and the positive would be at a bit more than the +4 foot end. Note that you can have more than one switch on each pin where the NC is connected in serial fashion and the NO is connected in parallel fashion (this can be seen on the diagram in the multiple limits switch section). The software configurations for the limits switches are under File -> Settings -> Limit.

A typical limit switch has three connections on it. These connections consist of COM (common), NC (normally closed) and NO (normally open). The COM would generally go to GND and the NC or the NO would go to the pin. If the NC is used, then the the switch is constantly connected until the switch is pushed (engaged) then the connection from the pin to gnd is broken (open). Use the settings in software to set whether in NC or NO configuration.

Let me know if this information was helpful (or not) by adding information to this question. Thanks.

User response:
Thank you very much for this helpful information. I'm still a little fuzzy on how the 6 limit switches physically connect to each other and to the USB breakout board. You've stated one switch (home) goes to positive and another switch (limit) goes to negative. Are all the GND prongs from all 6 switches connected to each other and going to GND on the breakout board, or no? And the NC prongs, how exactly are they connected to each other? And to the board? There has to be a diagram somewhere shows this visually, no? I don't know how to wire the switches in series or in parallel. I have already physically installed all the switches on the machine and ran the wires to where the board is. Now I just need to know where to plug these wires into the board. Also, taking into consideration that I'm using the Planet CNC software, the only settings I have pertaining to limit switches is "Enable/Disable" for each axis, and the actual limit for each axis. Nothing about NC or NO. Is that only in Mach3?
Thank you.

buildyourcnc response:
On the USB interface, the COM on the switch connects to GND and the NC or NO connects to the input pin (i.e. x++, y--, etc.)

Limit switch configuration is rather difficult to understand, especially with series and parallel. You can think of series as a single wire going from GND to the axis letter input terminal (i.e. X++ or X--). If the wire is broken, then the circuit is open (or the switch is engaged in a normally closed scenario). Normally closed is like an actual wire, and when engaged, the switch "opens" (breaks the wire). This is why we recommend in some systems that you can put many switches in series on a single pin. When one of the switches is engaged (breaking the connection) then the entire circuit of switches is broken and the machine stops.

In a parallel scenario, the state of the circuit is always broken until the one of the switches is engaged and the circuit is then closed or connected. The topology looks like a ladder. All the switches connect to both sides of the ladder and the switches are like the runs of the ladder (the horizontal bars that the feet are placed while climbing). Imagine all of the switches broken in this scenario (normally open). It would be like the ladder could be split in two, but if one of the ladder runs (switches) is closed by engaging it, then that run would connect both sides of the ladder and the two sides of the ladder would have a connection.

There is a diagram on the USB page of the various limit switch configurations. If you need more information (visual and/or otherwise), please let us know and we will immediately add that information to benefit everyone.

Click the link to add information to this solution:
I have nearly completed the CNC machine from the book, but I am using it with a USB breakout board, and have no idea how to wire the 6 limit switches to the board. I'm having difficulty following the diagram on the USB breakout board screen. Can someone please help me?

If you are using Mach3, the setting for the input pin 10 may be enabled as a default for use with the Emergency Stop. If there is no emergency stop on that pin, the reset will trip every time.

Click the link to add information to this solution:
I have the redleaf system for my black toe machine I have wired my limit switches in series NC after setting up in mach 3 I still get limit switch tripped after apply and ok setup can only run if I disable what am I doing wrong

BYCNC Response:
This is correct. You will need to use a method appropriate for the software you are using. Also remember that NC switches are typically wired in series, while NO switches are normally wired in parallel.

User Response:
I am using the cnc planet software for your USB board. Are the limit configurations in this software?

BYCNC Response:
Yes, Planet CNC software is compatible with the use of limit switches. Configuration information will depend on your specific application. You can view Planet CNC's information here: http://www.planet-cnc.com/files/CNCUSBController.pdf

Click the link to add information to this solution:
LIMIT SWITCHES FOR AXIS. THE PRINT SHOWS THAT YOU CAN WIRE LIMITS EITHER N.O. OR N.C. SO IF THIS IS CORRECT I WOULD NEED TO TELL BOARD IN SOFTWARE HOW LOOK AT THESE LIMITS, I'M GOING GET AN INPUT LOOSE DEPEND ON IT.

I will find this answer when I get into the office on Monday, but I have no problem sending out a replacement DVD out to you. If you would like to do this, please call us on Monday and let us know that you need a replacement DVD

Click the link to add information to this solution:
Hi Patrick back in 2013 I purchased the cnc hardware and plans kit. I misplaced the dvd which shows you how to configure the mach 3 software to the cnc machine I build. I it possible to get another dvd. Or do you have the information somewhere you the website or youtube?

The 5x10 greenBull base kit comes with the structure, hardware, and electronics for motion control. In order to have a fully functional CNC you will need a table base for your machine, a spindle or router to handle your cutting applications, end mills (bits) for cutting, CAD, CAM and CNC software, and a computer. There are also accessories you can add such as limit switches, emergency stops, and cable carrier for cable management. If you are looking for more information or a formal quote please contact sales@buildyoucnc.com

Click the link to add information to this solution:
I'm not sure of ALL the things I will need to do some of my ideas for the cnc machine. I'll mostly be cutting out 3/4" plywood projects. How much minimum for a 5' by 10' system? I need the hardware and software to get the job done. I saw the price for your basic unit 3-4 grand but don't know what all I NEED to start work.

To home the z-axis using a plate:
- Connect the end mill using a large clamping device like an alligator clip with a wire connected to GND.

- Connect the plate (solder a wire to the plate) to one of the input pins.

- You can use the autoset to setup that pin in Mach3 simply by touching the two together once connected to the pin and GND.

Alternatively, the end mill can be connected to the pin and the plate connected to GND as long as there becomes a complete circuit when the end mill touches the plate.

To setup homing for the Planet-CNC homing and limits, go to the Planet-CNC Machine setup page which explains the process step by step: http://www.planet-cnc.com/faq/machine_setup/

Customer Response:
How do I get homing on z to work with planet cnc software using build your own usb board. I have gone to planet website and followed the instructions provided but my software will not allow entries in the required fields they are grayed out is it because I am not using planet-cnc's board, I have used this method for years with Mach3 and would like to use it with the usb board and software.

Answer:
Just received information from the developer. The instructions on how to use a plate for z-axis homing (moveable sensor) can be found here:

http://www.planet-cnc.com/faq/moveable_sensor/

Click the link to add information to this solution:
How do I get Homing on Z to work with Plate and Ground using Buildyourcnc usb board all the entries for the sensor in planet-cnc are grayed out. I am using input z- and I purchased the software

if you purchased the USB interface, you will need planet-cnc software rather than Mach3, and you will need a usb cable to connect the usb interface to the computer.

The blackToe 2x4 CNC Machine Kit with optional table will need wire to connect the electronics. Don't forget to get some end mills to use for cutting the intended material.


Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
If I purchase the [blackToe 2x4 v4.1 CNC Machine Kit - USB Electronics - Table Included] all I would need for this CNC to be fully operational is a laptop with mach 3 software and a router. Is this correct?

Sure, the USB interface has a place for 4 axes of limit switches.

Each axis can have two limit switches: one for the ++ (positive) end and one for the -- (negative) end. The positive end would be the limit switch at the end of the machine that, say the machine has a 4'x8' area, reaches a bit after the 8 foot mark. The negative end would be the limit switch behind the 0 foot location behind the origin. If the origin is in the middle, the negative would be at a little more than the -4 foot end and the positive would be at a bit more than the +4 foot end. Note that you can have more than one switch on each pin where the NC is connected in serial fashion and the NO is connected in parallel fashion (this can be seen on the diagram in the multiple limits switch section). The software configurations for the limits switches are under File -> Settings -> Limit.

A typical limit switch has three connections on it. These connections consist of COM (common), NC (normally closed) and NO (normally open). The COM would generally go to GND and the NC or the NO would go to the pin. If the NC is used, then the the switch is constantly connected until the switch is pushed (engaged) then the connection from the pin to gnd is broken (open). Use the settings in software to set whether in NC or NO configuration.

Let me know if this information was helpful (or not) by adding information to this question. Thanks.

User response:
Thank you very much for this helpful information. I'm still a little fuzzy on how the 6 limit switches physically connect to each other and to the USB breakout board. You've stated one switch (home) goes to positive and another switch (limit) goes to negative. Are all the GND prongs from all 6 switches connected to each other and going to GND on the breakout board, or no? And the NC prongs, how exactly are they connected to each other? And to the board? There has to be a diagram somewhere shows this visually, no? I don't know how to wire the switches in series or in parallel. I have already physically installed all the switches on the machine and ran the wires to where the board is. Now I just need to know where to plug these wires into the board. Also, taking into consideration that I'm using the Planet CNC software, the only settings I have pertaining to limit switches is "Enable/Disable" for each axis, and the actual limit for each axis. Nothing about NC or NO. Is that only in Mach3?
Thank you.

buildyourcnc response:
On the USB interface, the COM on the switch connects to GND and the NC or NO connects to the input pin (i.e. x++, y--, etc.)

Limit switch configuration is rather difficult to understand, especially with series and parallel. You can think of series as a single wire going from GND to the axis letter input terminal (i.e. X++ or X--). If the wire is broken, then the circuit is open (or the switch is engaged in a normally closed scenario). Normally closed is like an actual wire, and when engaged, the switch "opens" (breaks the wire). This is why we recommend in some systems that you can put many switches in series on a single pin. When one of the switches is engaged (breaking the connection) then the entire circuit of switches is broken and the machine stops.

In a parallel scenario, the state of the circuit is always broken until the one of the switches is engaged and the circuit is then closed or connected. The topology looks like a ladder. All the switches connect to both sides of the ladder and the switches are like the runs of the ladder (the horizontal bars that the feet are placed while climbing). Imagine all of the switches broken in this scenario (normally open). It would be like the ladder could be split in two, but if one of the ladder runs (switches) is closed by engaging it, then that run would connect both sides of the ladder and the two sides of the ladder would have a connection.

There is a diagram on the USB page of the various limit switch configurations. If you need more information (visual and/or otherwise), please let us know and we will immediately add that information to benefit everyone.

Click the link to add information to this solution:
I purchased limit switches from you mounted them on my machine and wire them to the breakout for using pin 12 and the ground on the breakout board, after a few minutes I got a message about a limit switch trip. Am I supposed to use the extra outport on the board instead of the ground?

It seems to be getting some kind of interference or a short within the wiring or communication, try jogging the motors in the software without anything wired to the board. Then add one motor at a time to see if there is a short within your wiring or a faulty driver/motor.
If the USB breakout board continues to move the x-axis with no motors or driver wired to it, please email customerservice@buildyourcnc.com for a replacement or further troubleshooting.

Click the link to add information to this solution:
I AM USING USB BREAKOUT BOARD WITH PLANET-CNC SOFTWARE. WHEN ENABLE JOGGING KEYBOARD X AXIS STARTS TO MOVE BY ITSELF (WHETHER CONNECTED OF NOT). PRESS STOP - IT STOPS FOR A MOMENT AND THEN AGAIN. WHAT COULD THAT BE? TRIED REINSTALL SOFTWARE DID NOT HELP.

If you select the Settings Page and select or tick Auto Limit Override - this will allow you to back off the switch.

Additional Information:
limit and home switch

Click the link to add information to this solution:
Using Mach3 and the USB Controller, In initializing the 'Ref All Home' the machine goes thru the procedure of zeroing out 'Z' than move to zero out 'y', but when it move to 'x' it just stops when it hits the switch instead of zeroing out?

If you purchase the greenLean, you will get everything you need except a router, computer to operate the machine, and software to control the machine. You state that you have a computer. You can use this computer, but you will need to determine if it has a parallel port, or if you are going to need the USB controller option. As for the software, there are too many different options for you to choose from. We would not be able to tell you which to get, and how much it will cost you. This is a matter of preference. I can tell you, however, that you will need 3 types of software to complete a CNC project. You will need CAD software to design your design, CAM software to add tool paths and convert the design to g-code, and then control software to take the g-code and operate the machine.

Additional Information:
20

Click the link to add information to this solution:
Hello  We would like to buy a greenLean Vertically Oriented CNC Machine we start from scratch and want to make sure that we get all the pieces, we need  hardware and software we have a PC and a Mac

If you purchase the greenLean, you will get everything you need except a router, computer to operate the machine, and software to control the machine. You state that you have a computer. You can use this computer, but you will need to determine if it has a parallel port, or if you are going to need the USB controller option. As for the software, there are too many different options for you to choose from. We would not be able to tell you which to get, and how much it will cost you. This is a matter of preference. I can tell you, however, that you will need 3 types of software to complete a CNC project. You will need CAD software to design your design, CAM software to add tool paths and convert the design to g-code, and then control software to take the g-code and operate the machine.

Additional Information:
20

Click the link to add information to this solution:
Hello  We would like to buy a greenLean Vertically Oriented CNC Machine we start from scratch and want to make sure that we get all the pieces, we need  hardware and software we have a PC and a Mac

BYCNC Response:
This is correct. You will need to use a method appropriate for the software you are using. Also remember that NC switches are typically wired in series, while NO switches are normally wired in parallel.

User Response:
I am using the cnc planet software for your USB board. Are the limit configurations in this software?

BYCNC Response:
Yes, Planet CNC software is compatible with the use of limit switches. Configuration information will depend on your specific application. You can view Planet CNC's information here: http://www.planet-cnc.com/files/CNCUSBController.pdf

Click the link to add information to this solution:
Limit switches for axis. The print shows that you can wire the limits either n.o. or n.c. so if this is correct I would need to tell the board in the software how to look at these limits, I'm either going to get an input or loose an input depend on how i wire it.

The fact that you cannot move the motors with the keyboard serves as a clue to a couple possibilities.

- The software may not be communicating with parallel port. (One possibility may be that your step pins are not low active, or vice versa depending on your drivers).
- You may not be in the correct tab of Mach3. Make sure you are in the Program Run tab.
- The jog on/off button on the program run screen may not be lit (invoked).

This address below shows the complete troubleshooting for this type of situation. It will show how to test each pin at the parallel port at the back of the computer and everything else associated with correctly wiring the electronics.

https://buildyourcnc.com/CNCElectronicsandWiring.aspx




Additional Information:
6 axis robot with Mach3 Card 6 Axis Motion Controller

Click the link to add information to this solution:
I have a home built CNC running Mach 3. I have power to all the motors and the breakout board but no movement when running g-code. I cannot even manually move the motors with the arrow keys or page up and down. It also has an integrated 120v receptacle showing an open ground. I don't know if all this is related.

The diagram for wiring the USB interface board is located here: https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-USB-Controller-Breakout#prettyPhoto/2/

Under the board illustration, there are three smaller diagrams of limit switch wiring. On each, there are two connections, the GND and the pin which are labeled at the ends of the circuit on the diagrams. The pin side would go to the axis label ++ or -- terminal (i.e. X++, or X--). The other end, labeled GND would connect to any ground terminal on the board.

Click the link to add information to this solution:
I am using 5 limit switches on my 3 axis machine. I am using the usb controller for planet cnc. I would like to know where all the wires related to the limit switches get connected? A diagram would be helpful.