[ Log In ]
[ Register ]
NEW: CNC Router PLANS Available for all of our Newest CNC Models!! Click here to "Design Your CNC".

Question #: 2291

Question: does the uxp breakout broad work with mac 3

Current Solution

Our USB BoB does not work with Mach 3, and is currently only able to communicate/work through Planet-CNC.
Now the Parallel BoB does work with Mach 3, and other OS programs (ex. Aspire, etc) but cannot work with Planet-CNC.

Respond:

Other Possible Solutions to this Question

  • WILL THE USB BREAKOUT BOARD WORK WITH MACH3?

    Sure, the USB interface has a place for 4 axes of limit switches.

    Each axis can have two limit switches: one for the ++ (positive) end and one for the -- (negative) end. The positive end would be the limit switch at the end of the machine that, say the machine has a 4'x8' area, reaches a bit after the 8 foot mark. The negative end would be the limit switch behind the 0 foot location behind the origin. If the origin is in the middle, the negative would be at a little more than the -4 foot end and the positive would be at a bit more than the +4 foot end. Note that you can have more than one switch on each pin where the NC is connected in serial fashion and the NO is connected in parallel fashion (this can be seen on the diagram in the multiple limits switch section). The software configurations for the limits switches are under File -> Settings -> Limit.

    A typical limit switch has three connections on it. These connections consist of COM (common), NC (normally closed) and NO (normally open). The COM would generally go to GND and the NC or the NO would go to the pin. If the NC is used, then the the switch is constantly connected until the switch is pushed (engaged) then the connection from the pin to gnd is broken (open). Use the settings in software to set whether in NC or NO configuration.

    Let me know if this information was helpful (or not) by adding information to this question. Thanks.

    User response:
    Thank you very much for this helpful information. I'm still a little fuzzy on how the 6 limit switches physically connect to each other and to the USB breakout board. You've stated one switch (home) goes to positive and another switch (limit) goes to negative. Are all the GND prongs from all 6 switches connected to each other and going to GND on the breakout board, or no? And the NC prongs, how exactly are they connected to each other? And to the board? There has to be a diagram somewhere shows this visually, no? I don't know how to wire the switches in series or in parallel. I have already physically installed all the switches on the machine and ran the wires to where the board is. Now I just need to know where to plug these wires into the board. Also, taking into consideration that I'm using the Planet CNC software, the only settings I have pertaining to limit switches is "Enable/Disable" for each axis, and the actual limit for each axis. Nothing about NC or NO. Is that only in Mach3?
    Thank you.

    buildyourcnc response:
    On the USB interface, the COM on the switch connects to GND and the NC or NO connects to the input pin (i.e. x++, y--, etc.)

    Limit switch configuration is rather difficult to understand, especially with series and parallel. You can think of series as a single wire going from GND to the axis letter input terminal (i.e. X++ or X--). If the wire is broken, then the circuit is open (or the switch is engaged in a normally closed scenario). Normally closed is like an actual wire, and when engaged, the switch "opens" (breaks the wire). This is why we recommend in some systems that you can put many switches in series on a single pin. When one of the switches is engaged (breaking the connection) then the entire circuit of switches is broken and the machine stops.

    In a parallel scenario, the state of the circuit is always broken until the one of the switches is engaged and the circuit is then closed or connected. The topology looks like a ladder. All the switches connect to both sides of the ladder and the switches are like the runs of the ladder (the horizontal bars that the feet are placed while climbing). Imagine all of the switches broken in this scenario (normally open). It would be like the ladder could be split in two, but if one of the ladder runs (switches) is closed by engaging it, then that run would connect both sides of the ladder and the two sides of the ladder would have a connection.

    There is a diagram on the USB page of the various limit switch configurations. If you need more information (visual and/or otherwise), please let us know and we will immediately add that information to benefit everyone.

    Click the link to respond:
    WILL THE USB BREAKOUT BOARD WORK WITH MACH3?

  • Will the USB breakout board work with Mach3?

    Our newer USB board will work with Mach3 and can be found here at this URL:

    https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

    Click the link to respond:
    Will the USB breakout board work with Mach3?

  • Will the Mach 3 USB breakout board work with a Windows 7 64 bit system?

    I don't see why Mach3 under windows 64-bit wouldn't work with an interface that uses USB as it's primary communication method. I am a bit vague on this, so I will do more research on it.

    We recommend Mach3 run under Windows 32-bit when using the parallel interface as this is a legacy function.

    Additional Information:


    Additional Information:
    mach 3 usb board setup

    Additional Information:
    I am running Mach3 under Windows 7 Pro 64bit without any problems.

    Additional Information:


    Additional Information:

    Click the link to respond:
    Will the Mach 3 USB breakout board work with a Windows 7 64 bit system?

  • Does your breakout board work with low voltage 3.3volt parallel ports?

    The breakout board will work with 3.3 volt parallel port. The integrated circuits on the board bring the level up to 5 volts for each pin when engaged. The breakout board is powered from the USB port and this is where the 5 volts is acquired.

    Click the link to respond:
    Does your breakout board work with low voltage 3.3volt parallel ports?

  • Does the Laser Controller work with Mach3?

    The laser Controller will not work with Mach3.

    Click the link to respond:
    Does the Laser Controller work with Mach3?

  • Do you have a breakout board that will work with Mach4?

    You can find the cnc machine interface board here that works with Mach4:
    https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

    This board will work with Mach3 and Mach4. The board is filled with a wealth of options and features, including the ability to connect up to 8 axes (motor drivers), pendant, LCD, many outputs and inputs, separate pins for limit switches , 2 relays, Ethernet and USB interfacing.

    Additional Information:

    Click the link to respond:
    Do you have a breakout board that will work with Mach4?

  • will mach4 software work with planet CNC breakoutboard?

    Our USB breakout board, will not work with Mach 4! The USB BoB is specifically designed to work with Planet-CNC.

    Click the link to respond:
    will mach4 software work with planet CNC breakoutboard?

  • I have a 3 axis combo w/ parallel breakout board. Will this work with Mach 4?

    Our electronics kits with the parallel breakout board will work with Mach 4, however you will need to purchase the Legacy Driver for Mach 4 to work with our breakout board.

    Click the link to respond:
    I have a 3 axis combo w/ parallel breakout board. Will this work with Mach 4?

  • Does the usb controller (breakout) come with the needed usb cable?
  • MY COMPUTER DOES NOT HAVE A PARALLEL PORT. HOW DO I INTERFACE WITH THE BREAKOUT BOARD?

    If your computer does not have a parallel port, all you will need is a low cost PCI parallel adapter card (these can be found on amazon for $15-$20). If you plan on using a laptop (not recommended) you can try to find a PCMCIA parallel adapter, but many people have frequent issues with this setup. A more expensive solution would be to purchase a USB smooth stepper board. Unfortunately, we do not supply any of these adapters and cannot attest to their reliability.

    Additional Information:
    ur gay

    Additional Information:

    Click the link to respond:
    MY COMPUTER DOES NOT HAVE A PARALLEL PORT. HOW DO I INTERFACE WITH THE BREAKOUT BOARD?

  • Are the 3 axis electronics combos with the Mach 3 USB breakout board compatible with Mach 4?

    These boards are compatible with Mach3 only at this time. We will be adding a Mach4 board in the near future.

    Click the link to respond:
    Are the 3 axis electronics combos with the Mach 3 USB breakout board compatible with Mach 4?

  • can mach 3 be used with your usb breakout board?

    Mach3 is not compatible with the USB breakout board, so you need Planet CNC in its place.

    Additional Information:

    I am confused by this same issue. I am using the Mach3 USB interface board with Mach3 and it works fine. In fact a video of it is on this very website. (link below)

    Is the Mach3 USB interface board the same thing as Planet-CNC USB board?
    It has been stated on this FAQ that it cannot be used with Mach3 and can only be used with Planet CNC USB software.

    https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

    Click the link to respond:
    can mach 3 be used with your usb breakout board?

  • Will Mach3 USB Interface board fit in my redleaf, in lieu of the breakout board that came with it?

    The Mach3 USB board will fit in the redLeaf, but you may need to modify the Plexiglas top for proper mounting. However, the redLeaf has the proper parallel GPIO on the motherboard for use with the Parallel breakout board. If you have a laser on the machine you are using, then I would urge you to maintain the parallel breakout board as the Mach3 USB board will not work correctly using the Z-direction pin and you will need to determine how to use the output pins onthe USB board to ensure proper laser functionality.

    Click the link to respond:
    Will Mach3 USB Interface board fit in my redleaf, in lieu of the breakout board that came with it?

  • Does your parallel breakout board support macn4?

    Yes, the parallel breakout board can be used with the parallel plug-in that is offered by the mach CNC software developers.

    Click the link to respond:
    Does your parallel breakout board support macn4?

  • Will the mach3 usb interface card work with Windows 7?

    Yes, Mach3 (the software profram) will work with Windows 7, and windows 10 when coupled with the Mach3 USB interface. If you intend to use the parallel port driver, stick with Windows 7 in 32-bit mode.

    Click the link to respond:
    Will the mach3 usb interface card work with Windows 7?

  • Breakout Board with Relay. What is the USB connection on this board for? Does this board Still require a 5v power supply?

    We generally use the USB to power the interface (breakout board). The current from the computer is sufficient to supply the breakout board.

    Click the link to respond:
    Breakout Board with Relay. What is the USB connection on this board for? Does this board Still require a 5v power supply?

  • why does the parallel port breakout board have usb port?

    The parallel breakout board contains a USB port to power the board. Through the USB port, the computer delivers 5v of stable power to the parallel breakout board, but doe not provide any communication as would normally be associated with USB connectivity.

    The reason we elected to use the USB port to provide power is to remove the need for an external 5v wall adapter.

    Click the link to respond:
    why does the parallel port breakout board have usb port?

  • does breakout board with relay have built in pull up resistors for inputs?

    Both the inputs and the outputs on our parallel breakout board are built with pull up resistors. They are connected through resistor networks, going from VCC(5V) to the input/output pin.

    Click the link to respond:
    does breakout board with relay have built in pull up resistors for inputs?

  • can I use the usb on the parallel breakout board with planet cmc

    The USB on the Parallel breakout board, is used for powering the board itself (5v USB), and the Parallel to communicate directly between the drivers and the computer/mach 3.
    Planet-CNC cannot be used with our Parallel Breakout Board, it is only intend to be used with Mach 3/other open source programs.

    To use Planet-CNC, please refer to our USB breakout board! (https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-USB-Controller-Breakout)

    Click the link to respond:
    can I use the usb on the parallel breakout board with planet cmc

Get Help with:
This Product
Orders
Tech Support
Sales
This Product
Order Query
Tech Support
Sales
Not logged in. Log In Register
Track Order(s)
View Order(s)
I Want to Schecule a One-On-One Paid Tech Support Session
Book an Appointment Pertaining to a BuildYourCNC Product (Free)
Ask a Quesion Below (Free):
Book an Appointment Pertaining Other Equipment ($60/half hour)
Book an Immedite Appointment Pertaining Other Equipment ($120/half hour)
Ask a Quesion Below (Free):
Waiting for response... I may not answer immediately, but I was notified on my cellular phone so my response is forthcoming. If I don't respond immediately, you can always go to the [My Account] page to see all of our chats at any time.