The overall size of the machine, really depends on both the area available to you and also the overall size of material being used. Now our larger machines (blackFoot, greenBull, greenLean) can cut all the materials mentioned above, and if equipped with our 2.2kW spindle you will be accurate up to ten thousandths of an inch.
Our greenBull machine does have an option for a long-z axis, that was especially designed to cut foam, but depending on the overall size it might not be a requirement for the specified request.

Click the link to add information to this solution:
I HAVE A SIGN SHOP AND WE NEED CUT ALUMINUM, PLEXIGASS, FOAM AND OTHER MATERIALS FOR SIGNS. CAN YOU TELL ME WHAT MACHINE WE NEED? I LOOKING 4'X8' OR 5' X 10'

These machines are inherently dangerous. Before the machine moves, the machine should be clear of any person by a dimension of at the distance of a persons reach plus a few more feet. This is the policies we institute in our shop and what is recommend to all of our customers. Treat these machines as you would treat any major power tool in the shop.

With that said, you can certainly add some protective parts, but still keep folks away even with those installed. I would use the gantry side to do all of the mounting of the protective parts. Consider using sheet metal that you can bend and make a simple installation right on the gantry side.

Additional Information:

Click the link to add information to this solution:
THE CNC MACHINE IS UNSAFE WITH EXPOSED SPROCKETS THAT CAN DAMAGE FINGERS AND HAVE CLOTHING CAUGHT IN IT.

If your computer does not have a parallel port, all you will need is a low cost PCI parallel adapter card (these can be found on amazon for $15-$20). If you plan on using a laptop (not recommended) you can try to find a PCMCIA parallel adapter, but many people have frequent issues with this setup. A more expensive solution would be to purchase a USB smooth stepper board. Unfortunately, we do not supply any of these adapters and cannot attest to their reliability.

Additional Information:
ur gay

Additional Information:

Click the link to add information to this solution:
MY COMPUTER DOES NOT HAVE A PARALLEL PORT. HOW DO I INTERFACE WITH THE MACHINE?

The eyebolts are used in the squaring of the machine. I would use a standard carpenters square and first run the end mill along the edge of the square to first make it parallel with the long axis. Then run the end mill along the other edge with the short axis and adjust the eye bolts and chain according to the angle that the machine is out of square.

Additional Information:

Click the link to add information to this solution:
DO NEED TO SQUARE UP THE MACHINE AND IF SO YOU HAVE INSTRUCTIONS OR VIDEO FOR THIS?

The Greenbull machine can cut a very wide variety of materials ranging from foam to aluminum. We recommend the use of our 2.2kW spindle to allow the greatest flexibility. Aside from that, the most important thing is to use an appropriate end mill for the material you are cutting and to use appropriate speeds and feed rates.



BYCNC Response:
Our 40W laser can cut up to about 1/4" materials ranging from wood and acrylic down through lighter materials such as leather, fabric, foam, etc. Speed and final cut are greatly enhanced by an air assist upgrade. We also offer an 80W laser which has approximately twice the capabilities of the 40W.

Additional Information:

Click the link to add information to this solution:
WHAT MATERIALS CAN THE GREENBULL MACHINE CUT? LASER ETCH?

There are almost no limits to the kind of materials you can machine. Anything from wood or plastic to exotic materials like stainless steel can be cut as long as the part can be safely and firmly held and the proper cutting tool and cutting speed are used

Click the link to add information to this solution:
WHAT KIND OF MATERIALS CAN MACHINE?

If your computer does not have a parallel port, all you will need is a low cost PCI parallel adapter card (these can be found on amazon for $15-$20). If you plan on using a laptop (not recommended) you can try to find a PCMCIA parallel adapter, but many people have frequent issues with this setup. A more expensive solution would be to purchase a USB smooth stepper board. Unfortunately, we do not supply any of these adapters and cannot attest to their reliability.

Additional Information:
ur gay

Additional Information:

Click the link to add information to this solution:
IF MY COMPUTER DOESN'T HAVE A PARALLEL PORT, HOW DO I RUN THE MACHINE?

As you know, the plasma nozzle must be close to the cutting area and you will need some way to keep the nozzle at the right level with some type of device. The spray is downward, so you will need a contained area with a sheet of water at the bottom to extinguish he spray. You should have no problem using our machines for this application since you would need to product the table bed.

Click the link to add information to this solution:
DO WE CAN BUILD OUR CNC MACHINE WITH TOW TORCHES (PLASMA TORCH & OXY ACETYLENE TORCH)?

Yes, we have the optional table for the blackToe, but we need to fabricate it, which only takes one day. We generally reserve one week for the total fabrication and packing of all parts.

Click the link to add information to this solution:
DO YOU HAVE BLACKTOE MACHINES WITH TABLES READY TO GO OR HOW LONG DOES IT TAKE MAKE ONE?

PC with parallel port and USB port
20awg stranded wires for the motors - http://www.buildyourcnc.com/electronicscombo.aspx
18awg stranded wires for power supply to drivers
24awg stranded wires for breakout board to drivers
(location and spacing of components varies from one person to another, so we do not provide cables/wires)
- General purpose extension cord (cut the female end off) to provide power to power supply
- USB cable to power breakout board
- Parallel cable to communicate to breakout board
- Router
- (optional - instead of router) Spindle with power inverter http://www.buildyourcnc.com/SpindlesAndAccessories.aspx
- (if purchasing spindle with inverter) General purpose extension cord (240v) (cut the female end off) to provide power to power inverter
- End Mill(s) http://www.buildyourcnc.com/ProductsEndMills.aspx
- CAD, and/or CAD-CAM software (to produce geometry, machine operations, and g-code) http://www.buildyourcnc.com/CNCsoftware.aspx
- CNC control software (to read g-code and control machine) http://www.buildyourcnc.com/CNCsoftware.aspx
- If the machine does not have the table included, then a table will need to be built. The rails, chain and chain mounts are included that are used on this table.

Additional Information:

Click the link to add information to this solution:
WHAT ELSE DO I NEED WITH THE MACHINE?

What 3d printer do you have?

Additional Information:
whiteant

Click the link to add information to this solution:
HAVE 3D PRINTER THAT WANT TO MAKE CNC ROUTER ,IS THERE ANY GUIDES SHOW ME THE WAY

Yes, we have the optional table for the blackToe, but we need to fabricate it, which only takes one day. We generally reserve one week for the total fabrication and packing of all parts.

Click the link to add information to this solution:
DO YOU HAVE BLACKTOES WITH TABLES?

There are several CAD/CAM programs out there for MacOS. Here is a list of a few: http://www.macuser.de/forum/f53/3d-2d-cad-395058/#post4499316
I've also read good things about punchCAD: http://www.punchcad.com/
Of course, there is always SketchUp if you are in a pinch. There are a few CAM plugins for SketchUp as well, but I've never used them, so I can't vouch for them.

CAD/CAM will get you as far as designing your parts and producing the g-code, but if you also want to run the CNC machine with your Mac, you will need a piece of software similar to Mach3 or EMC to run the g-code. I haven't been able to find anything like these programs that runs on Mac, so you may have to run Mach3 or EMC in Windows using Boot Camp or a virtual machine such as VMware or Parallels.

Personally, I would use the Mac to do all the CAD/CAM, then use a cheap PC to run the CNC machine.

Additional Information:


Additional Information:
EasyDNC for OSX
www.dnc-x.com

Additional Information:


Additional Information:
Hi guys I’m new to the cnc and I’m beginning to learn how to operate and cad-cam software also my cnc runs on Mach3 my questions is if I should use MacBook to do all designs if I can have all this software to run on Mac or I have to use windows software to operate it? I have separate small computer connected to the cnc table who have Mach3 on it please help. Also if you know any other software much easy for beginners please let me know thank you guys!
My email if needed is r1jastrzebski@gmail.com

Additional Information:


Additional Information:
Hi , thank you for your advise!

Additional Information:
Hi , thank you for your advise!

Additional Information:
Hi , thank you for your advise!

Additional Information:
Hi , thank you for your advise!

Additional Information:

Click the link to add information to this solution:
DOES ANY OF THE SOFTWARE THAT COMES WITH IT COMPATIBLE MAC 10.6?

Hands-free cell phone car microphones have been tested by the manufacturers and meet the current ANSI/IEEE (American National Standards Institute/Institute of Electrical and Electronics Engineers) standards for radiofrequency (RF) safety. These are the same standards that the Federal Communications Commission enforces under the Telecommunications Act of 1996, and they place limits on the specific absorption rate (SAR) of RF energy in the body. Recent inflammatory articles in the British press were not substantiated by testing at ISO-accredited testing facilities at Motorola. Manufacturers of cell phones are required under FCC regulations to assure that their products meet the SAR limits on both hand-held and hands-free units. Further information can be obtained on the Internet at The Center for Devices and Radiological Health (FDA information) or Office of Engineering and Technology (FCC information).

Click the link to add information to this solution:
COULD YOU PLEASE EXPLAIN, IF IT'S TRUE, THAT HANDS-FREE CELL PHONE CAR MICROPHONES RADIATE MORE THAN ANY OTHER INSTRUMENT USED WITH THESE PHONES?

All of our CNC machines can cut melamine. If your application (kitchen doors) requires large cutting area, then I would recommend the following machines:

- greenBull 4x (4'x8'), 5x (5'x10') or 6x (6'x 12')

- greenLean 4'x8' vertically oriented CNC machine

- Or our Fabricator Pro 4'x8' metal CNC machine

Click the link to add information to this solution:
CAN YOU RECOMMEND WHICH CNC MACHINE TO GO WITH FOR CUTTING MELAMINE AND MAKING KITCHEN DOORS FROM MDF. ALSO DO PROVIDE TRAINING ON OPERATING SETTING UP SHOP PRODUCTION USE? THANKS

I haven't delved into using encoders with stepping motors too much. From my research, you need to have a controller that can provide the closed loop control, rather than software handling that process. I have also found from my research that using encoders on stepping motors is generally used to stop the machine in the case that the motor failed to achieve the commanded position for some reason and gives the user the chance to correct and continue with the job.

If you want proper closed loop control, it may be best to go with servos and servo controller that provide the closed loop control within the real of those two components.

Click the link to add information to this solution:
I HAVE NOT SEEN ANY REFERENCES TO ENCODER FEED-BACK CAPABILITY IN OF THE HARDWARE YOU SELL. THIS A SUPPORTED FEATURE WITH HARDWARE/SOFTWARE SELL?

The plug and play system does have enough memory for additional software. The redLeaf comes standard with a 1TB hard drive.

Click the link to add information to this solution:
DOES THE PLUG AND PLAY ELECTRONICS COMPUTER FOR 3 AXIS CNC MACHINE HAVE ENOUGH MEMORY RAM ADDITIONAL SOFTWARE (BOBCAD-CAM, BOBART, MACH3) TO BE ADDED FUNCTION WELL?

If your axis shutters and will not move unless moved by another force, that sounds like your acceleration is set too high. Lower the acceleration until it works well, then lower it a bit more to have a margin of safety.

IF that didn't work, try swapping the X and Y drivers. That way you will pinpoint if the issue is the driver. If the proplem persists, then there may be an issue with the motor itself.

The X and Y drivers can be easily swapped by swapping only the motor wires.

- Remove the x-axis motor wires from the X driver.
- Remove the Y motor wires from the Y driver.
- Insert the X motor wires into the Y driver.
- Insert the Y motor wires into the X driver.

Now the Y-axis will move the gantry. Test the Gantry movement by moving the Y axis using the up and down arrow keys (mach3).

Click the link to add information to this solution:
X AXIS STEPPER MOTOR STALLS AND SHUTTERS WHEN COMING FROM A STAND STILL WON'T MOVE WITHOUT PUSH BY HAND. I TOOK THE CHAINS OFF SPUN FINE WITH OUT LOAD. HAVE CHAIN HOOKED UP CAN MACHINE BACK FORTH HAND, NO HANG UPS OR ANYTHING, BUT TRY TO IT DOESN'T JUST SPINS OUT. ANY SUGGESTIONS?

PC with parallel port and USB port
20awg stranded wires for the motors - http://www.buildyourcnc.com/electronicscombo.aspx
18awg stranded wires for power supply to drivers
24awg stranded wires for breakout board to drivers
(location and spacing of components varies from one person to another, so we do not provide cables/wires)
- General purpose extension cord (cut the female end off) to provide power to power supply
- USB cable to power breakout board
- Parallel cable to communicate to breakout board
- Router
- (optional - instead of router) Spindle with power inverter http://www.buildyourcnc.com/SpindlesAndAccessories.aspx
- (if purchasing spindle with inverter) General purpose extension cord (240v) (cut the female end off) to provide power to power inverter
- End Mill(s) http://www.buildyourcnc.com/ProductsEndMills.aspx
- CAD, and/or CAD-CAM software (to produce geometry, machine operations, and g-code) http://www.buildyourcnc.com/CNCsoftware.aspx
- CNC control software (to read g-code and control machine) http://www.buildyourcnc.com/CNCsoftware.aspx
- If the machine does not have the table included, then a table will need to be built. The rails, chain and chain mounts are included that are used on this table.

Additional Information:

Click the link to add information to this solution:
WHAT WOULD NEED TO HAVE A FULLY OPERATIONAL MACHINE?