[ Log In ]
[ Register ]
NEW: CNC Router PLANS Available for all of our Newest CNC Models!! Click here to "Design Your CNC".

Question #: 3526

Question: Can the completely configured blueChick, with computer be shipped with working and test Unbuntu/EMC2 and not Windows/Mach3?

Current Solution

I noticed in the Computer CNC Systems of this webpage that Linux/EMC2 (now called LinuxCNC) is available on the preconfigured systems. The wording on the CNC Machines page makes it look like Windows7 is all that is available. So thats the best I can see for now as far as clarity.

Yes, if the redLeaf or redSprout is purchased with the machine, we can completely configure the electronics to use Ubuntu and Linuxcnc. If windows is selected, we install Windows 7 and completely configured under Mach3.

If Windows is not selected, we assume Ubuntu/Linuxcnc, but we always contact the customer to confirm in these cases.

Respond:

Other Possible Solutions to this Question

  • Can I get a replacement computer only ? I have a blacktoe with parallel port and it seems to have stopped working.

    Sure. If you had your own computer to start with and now need a replacement for it, consider our redSprout and redLeaf systems. You can find information about them here: https://buildyourcnc.com/AssembledElectronics.aspx If you started with one of our assembled systems, and only need to replace certain components, contact our sales department at sales@buildyourcnc.com for a quote.

    Click the link to respond:
    Can I get a replacement computer only ? I have a blacktoe with parallel port and it seems to have stopped working.

  • the computer is not able to wrk properly with the upgraded laser tube and power board and has an outdated software instilation.

    Is this a CO2 laser tube? CO2 laser tubes are not typically associated with the laser controller. The laser tube is powered by a laser tube power supply which is controlled by a simple digital on/off or PWM signal.

    If you got a higher powered laser tube, then the power supply for the laser tube needs to be correctly wired to the laser controller.

    Click the link to respond:
    the computer is not able to wrk properly with the upgraded laser tube and power board and has an outdated software instilation.

  • What's the cost of a Bluechick 4.2 with computer ready to go shipped to Reno NV. porter 892 set up.

    The price for the blueChick is here: https://www.buildyourcnc.com/blueChickVersion42CNCMachineKit.aspx

    You will want the kit without electronics that will cost $1360.00.

    Then you will need either the redSprout, or redLeaf CNC computer systems and the prices can be found here: https://www.buildyourcnc.com/AssembledElectronics.aspx

    The redLeaf has a bit more power and speed than the redSprout. You will need to purchase windows, found on that page, if you desire that OS to be installed. Otherwise, we will install Linux and linuxcnc. You will also need to purchase the length of motor wire that you need from the motors to the computer. This is variable and is determined by the position you wish locate the computer system with respect to the CNC machine.

    The shipping is determined at checkout. When you have the items in your cart, enter your shipping information and click on "calculate shipping". You will need to select your shipping preference, service and carrier.

    Click the link to respond:
    What's the cost of a Bluechick 4.2 with computer ready to go shipped to Reno NV. porter 892 set up.

  • Can I purchase a computer off Amazon (I have a machine I want to use) and still use the USB interface to drive it with LinuxCNC?

    You will need to build the table unit for your machine. There are instructions on how to do this at the bottom of the product page here, https://www.buildyourcnc.com/Item/cnc-machine-blackFoot-v4
    There is no estimate on how much this will cost though, since there are too many variables involved to do this.

    - PC with parallel port and USB port
    - 20awg stranded wires for the motors - http://www.buildyourcnc.com/electronicscombo.aspx
    - 18awg stranded wires for power supply to drivers
    - 24awg stranded wires for breakout board to drivers
    (location and spacing of components varies from one person to another, so we do not provide cables/wires)
    - General purpose extension cord (cut the female end off) to provide power to power supply
    - USB cable to power breakout board
    - Parallel cable to communicate to breakout board
    - Router
    - (optional - instead of router) Spindle with power inverter http://www.buildyourcnc.com/SpindlesAndAccessories.aspx
    - (if purchasing spindle with inverter) General purpose extension cord (240v) (cut the female end off) to provide power to power inverter
    - End Mill(s) http://www.buildyourcnc.com/ProductsEndMills.aspx
    - CAD, and/or CAD-CAM software (to produce geometry, machine operations, and g-code) http://www.buildyourcnc.com/CNCsoftware.aspx
    - CNC control software (to read g-code and control machine) http://www.buildyourcnc.com/CNCsoftware.aspx

    This answer is applicable to most of our machines with the exception of the greenLean and the blueChick since those machines are equipped with a table structure.

    Click the link to respond:
    Can I purchase a computer off Amazon (I have a machine I want to use) and still use the USB interface to drive it with LinuxCNC?

  • MY LASER MACHINE VERTICAL DOES NOT ACTIVATE THE LASER TUBE, VERIFY THE POWER SUPPLIES AND THEY ARE WORKING WHICH THE PROBLEM CAN BE

    Same issue here -- TTL output from the AWC708C never seems to be pulled low. Still troubleshooting.

    Click the link to respond:
    MY LASER MACHINE VERTICAL DOES NOT ACTIVATE THE LASER TUBE, VERIFY THE POWER SUPPLIES AND THEY ARE WORKING WHICH THE PROBLEM CAN BE

  • how much would your vertical laser kit cost without the wood components and door plastic shipped to Canada

    Good question. I will need to add up the cost. However, the complete kit with the wood components will cost in the range of $300 to $500 using freight.

    Additional Information:
    I will add a price option on the Vertical Laser XL page that shows the assembly price without the wood structural parts. Are you wanting the rails included in the price?

    Additional Information:
    Hi, I was expecting an email answer, I did not know that you answered. Also I am in Fiji, not Canada. There is a flaw with your question form, It would not accept Fiji because we have no postal codes, so I put in my old Canadian code so that it would accept my question.

    Yes we would need the rails and any mechanical and electrical components. Our plan is to build it against a wall in a shipping container.

    If you do not have a suitable freight forwarder I can ask at this end because people frequently receive shipping containers.

    Thank you,

    George

    Click the link to respond:
    how much would your vertical laser kit cost without the wood components and door plastic shipped to Canada

  • I'm looking for a complete CNC router, out the box ready to use system. Computer and software. What do you suggest? I need a working area of 12"x24"

    The bluchick CNC router is a perfect small format CNC that can handle most jobs. Please check here to see the latest information on this CNC router. blueChick CNC Machine. The machine can be purchased assembled. Al you will need is a computer and spindle.

    Click the link to respond:
    I'm looking for a complete CNC router, out the box ready to use system. Computer and software. What do you suggest? I need a working area of 12"x24"

  • can't get breakout board with relay working. in your video you show a 5v power supply input on the usb one but can't not find on this one?

    What part of your breakout board is not working? Are you having trouble getting a signal from the computer out of the breakout board to the drivers?

    The breakout board uses the USB as the 5v power source.

    Additional Information:
    Wiring the limit switches


    Additional Information:
    I am using my breakout board as port 2 from my ess smooth stepper only for limits so it's powered via 12v , now I want to use pin 17 to trigger my plasma will I still need to supply 5v power to is a well? As I'm not using the usb it's connected to smooth stepper via 25pin ribbin

    Click the link to respond:
    can't get breakout board with relay working. in your video you show a 5v power supply input on the usb one but can't not find on this one?

  • I had to wipe my computer due to virus and now can not download the USB software again. I get a "unhandled exception" error message. Any suggestions?

    An unhandled exception generally means that, in the program code, the program is not checking against every possible exception that could occur. Most likely, this exception is caused by some limit that is being exceeded (or the other way around). I would remove any files that could be associated with the program, like setting files, or even register configurations associated with that software. Also, make sure that you completely update your version of windows.

    Check to make sure all of the drivers are current for your graphics hardware. Make sure that your graphics hardware works in other programs as well.

    If you upgraded the Windows version, check to make sure your graphics hardware is compatible with the new version of Windows. Unhandled exception issue may be associated with graphics hardware and compatibility.

    Customer Response:
    I've given up on the wiped laptop and loaded the program on a different computer using windows 8. At first it won't operate my CNC until I read on Planet-CNC forum about loading the drivers on windows 8. All working now. Will run through the calibrations again today. Thanks

    Click the link to respond:
    I had to wipe my computer due to virus and now can not download the USB software again. I get a "unhandled exception" error message. Any suggestions?

  • Do you need to purchase the Black Toe with integrated computer if you have a dedicated computer to do deisgn and create g-code.

    If you have an existing PC with a parallel port you will not need to purchase the onboard computer system on the blackTooth laser cutter and engraver. You will want to purchase the blackTooth laser engraver that comes with the parallel interface (breakout board). If you have an existing CNC machine that is being used with this PC, you can disconnect the CNC machine and connect the blackTooth to this PC. You will want to have two configurations for your control software.

    Additional Information:
    We have a version of the blackTooth that is 110v and 220v. We generally determine which is sent according to the requirements of the customer and in what country they live.

    Additional Information:
    20

    Additional Information:
    Parallel Port Configuration BIOS settings and Mach 3.

    Click the link to respond:
    Do you need to purchase the Black Toe with integrated computer if you have a dedicated computer to do deisgn and create g-code.

  • What kind of computer comes with the blacktooth and do i need to install windows after purchase?

    For the integrated computer for the blackTooth, the hard drive doe not need to be formatted, but will require an OS (operating system) to be installed. Ubuntu Linux can be installed with the CNC integrated software from Linuxcnc.org. Windows can also be installed.

    Click the link to respond:
    What kind of computer comes with the blacktooth and do i need to install windows after purchase?

  • I am interested in buying Laser Cutter/Engraver with Integrated Computer, so can you please let me know if your offer still stands?

    The (blackTooth) laser cutter and engraver comes with the unit shown on the product page seen here: https://buildyourcnc.com/blackToothLaserCutterAndEngraver.aspx

    The unit is intended to be set on a table top.

    The stand that you may have noticed was only a demonstration on how to use SketchUP in a CNC process scenario. The stand has never been offered with the blackTooth laser.

    Click the link to respond:
    I am interested in buying Laser Cutter/Engraver with Integrated Computer, so can you please let me know if your offer still stands?

  • My computer cannot communicate with the AWC608

    If you are getting the "Communicating Unsuccessful!" error when you are trying to communicate between LaserCAD and the AWC608 Laser Cutter and Engraver controller (after you have already tried installing the USB driver from the LaserCAD setup procedure), these are the steps you will need for a successful communication:

    - Open the Device Manager window (right click on the start menu and select Device Manager)
    - When you plug the USB cable from the AWC608 Laser Cutter Controller (USB Type B connector) to the computer, you should see a new item in the Device Manager, possibly under "Ports (COM & LPT)", or under "Other Devices". It may show as an item under "Other Devices", possibly FT245R and has an "!" in a yellow triangle.
    - Download the latest FTDI drivers from: http://www.ftdichip.com/Drivers/D2XX.htm
    - Unzip the files to a folder that can be easily browsed.
    - Right click on the item that appeared in the Device Manager when the cable was plugged in between the Laser Cutter AWC608 controller and the computer.
    - Click on update driver
    - Select the procedure to manually install the driver and browse to the folder containing the FTDI driver and follow the step in the driver installation wizard.
    - The item should now be located under the "Ports (COM & LPT)" and should be named "USB Serial Device (COM#)". The # will be the number you will use in the LaserCAD software.
    - In the LaserCAD software, click the "Select Mode" at the far top right of the Laser CAD user interface.
    - Make sure USB mode is selected.
    - If the Machine name with the correct COM number is listed, select it and exit the dialog window. Otherwise, click on "Add" and fill in the details with the new COM number.

    Additional Information:


    Additional Information:
    Communicating unsuccessful

    Additional Information:
    Communicating unsuccessful

    Click the link to respond:
    My computer cannot communicate with the AWC608

  • parallel break out board is not working-relay keeps switching my computer off when I power up

    Do you have anything connected to the relay?

    Additional Information:
    is the relay controlled by a pinout on the BoB?

    Additional Information:
    Nothing is attached to the relay pins I am only using 2 and 3 and 5v for x driver and led indicator, 4 and 5 and 5v for y driver and led indicator, and 6 to fire the laser and the led indicator. I am also using a 5v out for the laser power control circuit and one pin of the 5k pot. Ground is shared on the laser power supply, the cnc power supply and the x and y driver. I am using the computer motherboard supplied by Buildyoucnc running ubuntu 12.04.5 LTS and linuxcnc. Bios is set to use ECP, I have tried normal and I have tried EPP, all with the same results. If I plug in the parallel after the computer starts up it doesn't switch but I can't control either axis motors


    Additional Information:
    Laser is currently not connected for safety reasons


    Additional Information:
    I am using the parallel BoB for the 40 watt C02 Laser Cutter and Engraver(blacktooth), with the supplied integrated computer running Ubuntu 12.04.5 LTS and linuxcnc. Right now, when I have the parallel header connected to the BoB(as well as usb power supplied by the computer) and I start the computer, I am able to see the first splash screen of text indicating that the computer is starting up, then the relay on the BoB switches, turning the computer off and then back on again. This happens over and over again and the computer cannot fully start into the linux os. If I unplug the parallel cable from the BoB, I can start the computer, sign in and then plug the BoB back in without it shutting down the computer. Can anyone explain why this happens? I should also say that I cannot talk to the steppers in stepconfig of linuxcnc, I get to the test this motor section and nothing happens when I try to jog either the x or y motors. In the y config, I actually triggered the relay and sent the machine back into the start up failure loop I mentioned in the beginning.

    Additional Information:
    Fixed this problem, the parallel cable was not seated well, found some screws to make a strong connection, now that part is working. Unfortunately, the stepconfig in linuxcnc is still not talking to the motor drivers and the setup for determining steps for inch in the build instructions is nothing like the set up in linuxcnc. In the instructions it says motor steps per revolution*microsteps/pulley pitch per tooth*number of teeth and in this case the recommended input would be (200*16)/.08*20 teeth = 2000 steps per inch the formula in linuxcnc is very different

    Click the link to respond:
    parallel break out board is not working-relay keeps switching my computer off when I power up

  • Do I need to install cad\cam,and control software to test x,y,and z hardware when it is completely installed?

    The driver and motor need a pulse train signal from the computer to move the motors, so it would be best to at least install the control software and use the jog feature to test the motors.

    Click the link to respond:
    Do I need to install cad\cam,and control software to test x,y,and z hardware when it is completely installed?

  • If I understand correctly, the greenBull kit comes with a spindle and laser. What else do I need to have a working machine. Obviously a table, do I also need the computer, software, wires, pump and plumbing, electronics, VFD, steppers and controllers?

    The greenBull kit (not the assembled) will need the table (the rails for the table is supplied), wires/cables for the stepper motors and stepper motor drivers, smaller gauge wires for digital wire connections (limit switches, drivers to control interface, etc), wires for the spindle connection to the VFD, tubing for water flow to and from the spindle, and a pump and reservoir (we are just about to introduce a small pump/reservoir/radiator/fan system for use with the spindle. The VFD/spindle, stepper motors/drivers and interface board are included.

    Click the link to respond:
    If I understand correctly, the greenBull kit comes with a spindle and laser. What else do I need to have a working machine. Obviously a table, do I also need the computer, software, wires, pump and plumbing, electronics, VFD, steppers and controllers?

  • Lost Comm with steppers: I have been running Mach3 with my Black Toe for years. This morning, I booted up, motors locked up. Started Mach, hit reset, and nothing. Can't move. Checked plugs. Diag screen says OK. What to look for? I have the BYOCNC Computer/contoller box.

    New clues. I loaded a different profile I have used for another machine and my Black Toe moves. Of course all the settings are different. I load my normal profile and no ports, pins, or outputs light up.

    Click the link to respond:
    Lost Comm with steppers: I have been running Mach3 with my Black Toe for years. This morning, I booted up, motors locked up. Started Mach, hit reset, and nothing. Can't move. Checked plugs. Diag screen says OK. What to look for? I have the BYOCNC Computer/contoller box.

  • I have a parallel. breakout board. and no parallel port at the back of my computer do those parallel. cards. work with the breakout board?

    If your computer does not have a parallel port, all you will need is a low cost PCI parallel adapter card (these can be found on amazon for $15-$20). If you plan on using a laptop (not recommended) you can try to find a PCMCIA parallel adapter, but many people have frequent issues with this setup. A more expensive solution would be to purchase a USB smooth stepper board. Unfortunately, we do not supply any of these adapters and cannot attest to their reliability.

    Additional Information:
    ur gay

    Click the link to respond:
    I have a parallel. breakout board. and no parallel port at the back of my computer do those parallel. cards. work with the breakout board?

  • Is there a way to test input pins on your breakout board? I had pin 10 exclusivley configured to the estop switch, got a lot of false estops. I gave up on usung estopp and tride to configure pin 10 to a probe with what seemed to be false indicators of a closed circuit.

    To test input pins, we would usually recommend using a working limit switch or component. Which would allow you to view the current pin, for any problems or incorrect setting with the control software.

    When you wired the e-stop to pin 10, you did wire it in as normally open and also designated the correct pin to the e-stop in the control software?

    We also have noticed how sensitive limit switches and e-stops can be to noise around the system and through the wiring. We would recommend using a shielded cable and wiring/routing away from any other wires(power, communication, etc.).

    Click the link to respond:
    Is there a way to test input pins on your breakout board? I had pin 10 exclusivley configured to the estop switch, got a lot of false estops. I gave up on usung estopp and tride to configure pin 10 to a probe with what seemed to be false indicators of a closed circuit.