You can use our shopping cart to determine the shipping. Add the machine and the parts you want to purchase, enter your shipping address and click on the Calculate Shipping Button to get a price for shipping. The shipping charges are determined directly from the carriers at the time of pressing that button.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
Hi, I live in Australia and am looking at purchasing the Blacktooth laser cutter and engraver. I am wondering what the cost to ship to Australia would be?

Temperature probe monitor. Very valuable. This keeps you up to date on your coolant temperature levels.

Voltage meter. This will tell you the exact level of voltage/power you are running telling the laser to run at instead of an arbitrary mark on a drawn wheel around your POT.

Ammeter sensitive to 1mA. This will be sure your not over driving your tube and reducing it's life significantly.

Hour meter. This will tell you exactly how long your system has been 'on' giving you a more accurate bead on the length of your tubes life.

Exhaust fan upgrade. The current fan included is 100CFM. You can buy 120mm fans that push 250CFM and I have included a guide on how to go about doing this here. http://buildyourtools.com/phpBB3/viewto ... 8cdd1802bf

To push the exhaust fan even further, if you have the room/power, I would highly recommend investing in a 600+ CFM "Dust Collector" system. 250CFM is still not suffice to draw all the smoke that can come off of 3mm or 1/8 MDF cutting job.

A cutting surface. I bought myself a aluminum 'egg crate' mesh from my local HVAC company. They are used a cover for fluorescent lights and work great for low impact cutting surface. They come in 4'x8' sheets and are easily cut to fit. The other side is if you can find a steel honeycomb cutting bed to fit. These can be quite costly or fairly affordable depending where you are looking. The benefit of a steel honeycomb is you can use high power magnets to hold material down.

Click the link to add information to this solution:
WHAT ARE SOME USEFUL MODIFICATIONS CAN APPLY TO THE BLACKTOOTH LASER CUTTER?

You can find the wiring diagrams for the blackTooth on step 105 and 106 on the list of instructions on the blackTooth page. Step 105 pertains to the parallel breakout board and step 106 pertains to the USB interface board.

Additional Information:
wire size

Click the link to add information to this solution:
WHERE ARE THE WIRING DIAGRAMS FOR BLACKTOOTH LASER CUTTER IN INSTRUCTIONS?

Hour meter. This will tell you exactly how long your system has been 'on' giving you a more accurate bead on the length of your tubes life.

Click the link to add information to this solution:
WHAT CAN ADD TO MY BLACKTOOTH LASER CUTTER MEASURE THE TIME OF USE?

Temperature probe monitor. Very valuable. This keeps you up to date on your coolant temperature levels.

Voltage meter. This will tell you the exact level of voltage/power you are running telling the laser to run at instead of an arbitrary mark on a drawn wheel around your POT.

Ammeter sensitive to 1mA. This will be sure your not over driving your tube and reducing it's life significantly.

Hour meter. This will tell you exactly how long your system has been 'on' giving you a more accurate bead on the length of your tubes life.

Exhaust fan upgrade. The current fan included is 100CFM. You can buy 120mm fans that push 250CFM and I have included a guide on how to go about doing this here. http://buildyourtools.com/phpBB3/viewto ... 8cdd1802bf

To push the exhaust fan even further, if you have the room/power, I would highly recommend investing in a 600+ CFM "Dust Collector" system. 250CFM is still not suffice to draw all the smoke that can come off of 3mm or 1/8 MDF cutting job.

A cutting surface. I bought myself a aluminum 'egg crate' mesh from my local HVAC company. They are used a cover for fluorescent lights and work great for low impact cutting surface. They come in 4'x8' sheets and are easily cut to fit. The other side is if you can find a steel honeycomb cutting bed to fit. These can be quite costly or fairly affordable depending where you are looking. The benefit of a steel honeycomb is you can use high power magnets to hold material down.

Click the link to add information to this solution:
HOW CAN YOU ENHANCE THE BLACKTOOTH LASER CUTTER?

If you take the standard parallel cable BoB (Break Out Board), then you will need control software (Mach 3 or EMC2) and CAM software to make your G-Code (such as CamBam). Personally I use CamBam and Mach 3, they work beautifully but don't expect to turn them on and know how they work out of the box. Give yourself a few weeks to get familiar with the basics. CamBam is VERY powerful software for it's price. I'm surprised how much I keep learning on what I can do with it...I highly recommend it if you want as much control as possible.

Mach 3 + CamBam as a bundle costs $310. EMC2 will give you a free replacement for Mach 3 and is exclusively for Linux.

If you use the USB BoB, it will cost an extra $75 + $75 for the software. This is an all-in-one package so no need for Mach 3 or CamBam.

For etching rasters (jpeg, bmp, tiff, non-vectors, photos), I highly recommend PicEngrave. It has been a labor of love for the past 9 years and John has done a wonderful job with it. It easily compares in quality compared to software that is in the $200-$300 range. John's software runs $40 and can be found here: http://picengrave.com/ (don't let the modest website fool you, this stuff can do amazing things). DotG and the Mach3 engrave plugin are two other options and instructions can be found on Dustans page in the gallery on buildyourcnc.com website.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
WHAT SOFTWARE CAN BE USED WITH THE BLACKTOOTH LASER CUTTER?

If your country requires 220 volt peripherals (water pump or air pump) for the blackTooth laser system, then we will either send the 220/240 volt equivalents, or we will have them drop shipped from another location in your country, or a country with compatible power requirements.

Click the link to add information to this solution:
What's the cure for 110 volt pumps (air and water) and a 110volt laser power supply, in a Blacktooth Kit sent to Australia, where 240 volts is pleasingly normal. The fan and other power supply are 220 volts.

The blackTooth Laser cutter and Engraver can be built in a weekend. Take a look at the build instructions and try to determine if you feel you have sufficient capability to put together the laser system.

Click the link to add information to this solution:
HOW DIFFICULT IS IT TO BUILD THE BLACKTOOTH LASER CUTTER?

If the laser tube is the same dimensions then yes, that tube can be implemented and take into account the required laser power supply and safety protocols on that high powered laser tube.

Our blackTooth is a fixed machine and is only made for the 40 watt laser tube that we sell.

Click the link to add information to this solution:
Can we use a more powerful laser tube in the blackTooth? Say, 100w from ColeTech? Are they just physically too large/long?

A cutting surface. I bought myself a aluminum 'egg crate' mesh from my local HVAC company. They are used a cover for fluorescent lights and work great for low impact cutting surface. They come in 4'x8' sheets and are easily cut to fit. The other side is if you can find a steel honeycomb cutting bed to fit. These can be quite costly or fairly affordable depending where you are looking. The benefit of a steel honeycomb is you can use high power magnets to hold material down.

Click the link to add information to this solution:
WHAT CAN USE BELOW MY WORKPIECE AS SUBSTRATE IN BLACKTOOTH LASER CUTTER?

Gcode or digital files are not available for our machines.

Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
I have the build your own CNC kit 3 Axis CNC Machine 2008, were can I get the Gcode or vector files for it ? I wanted to have it laser cut

We are working on getting these on the blackTooth page


Additional Information:
Ok, thanks. Do you use a separate 24V P/S for the supply voltage on the AWC708C or tap into the stepper motor P/S?

Click the link to add information to this solution:
Do you have instructions how to mount the AWC708 DSP on the blackTooth?

Controlling a 3-axis or 4-axis motor configuration, you will need the following items drivers/motors/controller. Our electronics combo comes with the items mentioned and with power supply/miscellaneous items.
The only other item needed will be a computer (with controller software) to communicate and view controls of your motors.
Using the Parallel breakout board will use Mach 3 software, and USB will use Planet-CNC software.

Additional Information:
You can use this link to see the videos on how to connect the electronics together and make them work: https://www.buildyourcnc.com/tutorials/tutorial-Electronics-USB-Interface-Wiring

Click the link to add information to this solution:
hey, where can i see the steps how can i control 3 or 4 step motor? can i use the Axis Electronics Combo? or i need to connect controller?

All the options for and variations of our blackTooth laser cutter/engraver are available on our website here https://buildyourcnc.com/blackToothLaserCutterAndEngraver.aspx#prettyPhoto. The wiring diagram is available here: https://buildyourcnc.com/blackToothLaserCutterAndEngraver.aspx#prettyPhoto/0/
We do not offer plans or a bill of materials for our machines at this time, but if you are interested in doing your own from scratch you can learn a lot about the design and build process from our tutorials. We wish you success in your endeavors.

Click the link to add information to this solution:
How can i get a complete list of all the components (electronics) I need for a CNC laser cutter with the laser controller? A wiring Diagram would probably be very helpful.

We don't offer those drive pullies with a 3/4" bore at the moment. We can supply them if you are willing to wait. If so, what is the pulley pitch, how many teeth and the width of the belt.

Additional Information:
Meant to say pulleys, not pullies.

Click the link to add information to this solution:
Do you offer or can recommend a place where I can buy the Drive Pulley for NEMA 43 Stepper Motor (1586 oz-in 3/4" single shaft) 5.5 Amps?

Same issue here -- TTL output from the AWC708C never seems to be pulled low. Still troubleshooting.

Click the link to add information to this solution:
MY LASER MACHINE VERTICAL DOES NOT ACTIVATE THE LASER TUBE, VERIFY THE POWER SUPPLIES AND THEY ARE WORKING WHICH THE PROBLEM CAN BE

The mirrors can be aligned using the two positioning screws on the mirror itself.

Here are some videos to help:
Part 1:

Click the link to add information to this solution:
Troubleshooting Blacktooth alignment issues. In the center position, all is aligned. Moving the nozzle to the positive or negative side and you can see it steadily moves to the top left or bottom right of the hole. Adjusting the mirrors does not resolve. Is this a problem with the build itself? Here's a video of what's happening. https://www.youtube.com/watch?v=av7dxyfaJc4

Are you able to install a newer version of Mach3? If you are worried that your configuration will be lost, you can save the configuration by copying all of the XML files from the Mach folder. The XML files contain all of the settings that you applied in Mach3. Just in case the XML files are not compatible with the new version, make sure not to erase the current Mach3 that you have on the machine.

Click the link to add information to this solution:
[575] Hi, I have an old version of MACH3 V1.84 - Can someone tell me where to place the USB motion drive as there is no plugin folder in this version.

A standard 40W CO2 laser will cut up to 1/4" thick of material, be it wood, acrylic, card stock, leather, fabric, foam, cork, etc. (Decent speed and final cut are heavily dependent on a strong air assist upgrade)

Metals cannot be cut due to the power level and wavelength of the CO2 laser. But it can be marked with special solutions like Cermark or Thermark.

Click the link to add information to this solution:
WHAT THICKNESS OF MATERIAL CAN THE BLACKTOOTH LASER CUT?