[ Register ]

### Question #: 3551

Question: what are the exchage rates for europe?

Current Solution

The best way to find the exchange rates for Europe is to google "exchange rates for europe":

Respond:

### Other Possible Solutions to this Question

• WHAT ARE THE CABLE LENGTHS FOR BLACKTOE

The motor cables for the blackToe are as follows:

Total 30 feet

X - 9
Y - 10
Z - 11

WHAT ARE THE CABLE LENGTHS FOR BLACKTOE

• WHAT ARE THE CABLE LENGTHS FOR BLACKTOE

The motor cables for the blackToe are as follows:

Total 30 feet

X - 9
Y - 10
Z - 11

WHAT ARE THE CABLE LENGTHS FOR BLACKTOE

• what is the price for Planet-CNC software?

The base price for planet cnc is 69 Euros, which translates to \$85.85 dollars. Can be found here (http://www.planet-cnc.com/index.php?page=shop)

what is the price for Planet-CNC software?

• WHAT CABLE LENGTHS ARE USED FOR THE BLACKTOE

The motor cables for the blackToe are as follows:

Total 30 feet

X - 9
Y - 10
Z - 11

WHAT CABLE LENGTHS ARE USED FOR THE BLACKTOE

• WHAT ARE THE DIMENSIONS FOR GREENBULL TABLE?

Actual table dimension: 4'x8' is 56.078"x 121.50" (the overhang in the illustrations should be 3/4" thick)
To determine the frame dimensions, first consider using the frame height shown of almost 3' (2.86'). The width of the frame should be 4" narrower than the dimension from rail edge to rail edge (6X rail to rail is 80.078"). This will provide a 2" overhang on both sides (4X frame width should be 56.078").
The length of the frame should be 4" shorter than the desired length of the rails to provide a 2" overhang on both ends. The travel length will be 20" shorter than the rail length due to the space occupied by the gantry sides.
Two long pieces of 3/4" material will need to be placed on top of the frame with the 2" overhang on the sides and the end. These long strips of material will receive the rails and the chain mounts on the ends.

https://www.buildyourcnc.com/Item/cnc-machine-greenBull-v4-4X

WHAT ARE THE DIMENSIONS FOR GREENBULL TABLE?

• what are the motor setting for the greenbull

In the customer service live, just enter "motor tuning" and it will give you a list of all the recommended or default settings for our machines. However the acceleration and velocity for the greenBull(other machines) will be an actual determination on your trials. You will want the highest possible acceleration and velocity without the motors stalling, so you can do increments of ten to be on the safe side, if it is too slow try increments of 25.

The steps per inch is dependent on the microstepping:
Steps/Inch for the x and y
Steps = 200 motor steps per revolution x 16 microsteps = 3200 steps
Inches = sprocket number of teeth x pitch of the sprocket = 14 x .25" = 3.5 inches
steps/inch = 3200 / 3.5 = 914.28
This is really a starting point. You will then need to use the mach3 calibration function to get the perfect steps/inch value. Use as long a measurement as possible when calibrating.

Velocity:
Start with a value of 1000 ipm. Increase this value with a relatively low acceleration at about 10. You will notice at a particular velocity that it will stall. This is your stall velocity. I would take the stall velocity and reduce it by about 30% to 50% which should give you a good final safe velocity.

Acceleration:
Once the velocity is found, raise the acceleration until it start to stall at a low velocity. Reduce the acceleration by about the same percentage to stick with a safe acceleration.

The acceleration is mostly dependent on torque (current) and the top speed is dependent on the amount of voltage.

Give some tests with all of the axes running at the same time. If you notice and stalling, reduce velocities and acceleration depending on when the stall happens (top end, or acceleration curve).

X-axis
“CW8060 (6.0A) Driver”
Set to 5.43A, 1/16 Microstep
Dipswitches: 01100110 (“0”=down, “1”=up)
Mach3 Motor Tuning: 914.29 steps/in
Y-axis
“CW8060 (6.0A) Driver”
Set to 5.43A, 1/16 Microstep
Dipswitches: 01100110
Mach3 Motor Tuning: 914.29 steps/in
Z-axis
“CW8060 (6.0A) Driver”
Set to 5.43A, 1/4 Microstep
Dipswitches: 01100100
Mach3 Motor Tuning: 1600 steps/in

4th axis

what are the motor setting for the greenbull

• WHAT ARE THE SHIPPING DIMENSIONS FOR GREENBULL?

76" X 40" X 26"
230 LBS

WHAT ARE THE SHIPPING DIMENSIONS FOR GREENBULL?

• What are the dipswitch settings for the drivers?

blueChick:

X-axis
“CW230 (3.0A) Driver”
Set to 1/16 Microstep, 2.7A
Dipswitches: 11001100
Mach3 Motor Tuning: 1422.22 steps/in

Y-axis
“CW230 (3.0A) Driver”
Set to 1/16 Microstep, 2.7A
Dipswitches: 11001100
Mach3 Motor Tuning: 1422.22 steps/in

Z-axis
“CW230 (3.0A) Driver”
Set to 1/4 Microstep, 2.7A
Dipswitches: 10101100
Mach3 Motor Tuning: 1600 steps/in

blackToe:

X-axis
“CW230 (3.0A) Driver”
Set to 1/16 Microstep, 2.7A
Dipswitches: 11001100
Mach3 Motor Tuning: 1422.22 steps/in

Y-axis
“CW230 (3.0A) Driver”
Set to 1/16 Microstep, 2.7A
Dipswitches: 11001100
Mach3 Motor Tuning: 1422.22 steps/in

Z-axis
“CW230 (3.0A) Driver”
Set to 1/4 Microstep, 2.7A
Dipswitches: 10101100
Mach3 Motor Tuning: 1600 steps/in

blackFoot:

X-axis
“CW8060 (6.0A) Driver”
Set to 1/16 Microstep, 2.7A
Dipswitches: 11001100 (“0”=down, “1”=up)
Mach3 Motor Tuning: 914.29 steps/in

Y-axis
“CW230 (3.0A) Driver”
Set to 1/16 Microstep, 2.7A
Dipswitches: 11001100
Mach3 Motor Tuning: 1422.22 steps/in

Z-axis
“CW230 (3.0A) Driver”
Set to 1/4 Microstep, 2.7A
Dipswitches: 10101100
Mach3 Motor Tuning: 1600 steps/in

greenBull:

X-axis
“CW8060 (6.0A) Driver”
Set to 5.43A, 1/16 Microstep
Dipswitches: 01100110 (“0”=down, “1”=up)
Mach3 Motor Tuning: 914.29 steps/in

Y-axis
“CW8060 (6.0A) Driver”
Set to 5.43A, 1/16 Microstep
Dipswitches: 01100110
Mach3 Motor Tuning: 914.29 steps/in

Z-axis
“CW8060 (6.0A) Driver”
Set to 5.43A, 1/4 Microstep
Dipswitches: 01100100
Mach3 Motor Tuning: 1600 steps/in

Scratch-Build / Book-Build Kit:

X-axis
“CW230 (3.0A) Driver”
Set to 1/4 Microstep, 2.7A
Dipswitches: 10101100 (“0”=down, “1”=up)
Mach3 Motor Tuning: 1600 steps/in

Y-axis
“CW230 (3.0A) Driver”
Set to 1/4 Microstep, 2.7A
Dipswitches: 10101100
Mach3 Motor Tuning: 1600 steps/in

Z-axis
“CW230 (3.0A) Driver”
Set to 1/4 Microstep, 2.7A
Dipswitches: 10101100
Mach3 Motor Tuning: 1600 steps/in

Scratch built/book CNC with NEMA 34 motors and CW8060 microstep driver

What are the dipswitch settings for the drivers?

• WHAT ARE THE SHIPPING DIMENSIONS FOR VERTICAL LASER

Shipping crate size 121" X 36" X 92"

Weight 511 LBS

WHAT ARE THE SHIPPING DIMENSIONS FOR VERTICAL LASER

• What are the overall dimensions for a greenbull 5x10

The overall size (Foot Print(Roughly)) is:
W: 90" x L: 142.5" x H: 35"

Height:
Is from table top to highest point and not from the floor to highest point.(H for the 5X/6X can vary in size due to the height of the table/frame, since it can be adjusted to the specific needs of the customer)).

What are the overall dimensions for a greenbull 5x10

• What breakout board do i need for the mach4 software?

You can find the cnc machine interface board here that works with Mach4:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

This board will work with Mach3 and Mach4. The board is filled with a wealth of options and features, including the ability to connect up to 8 axes (motor drivers), pendant, LCD, many outputs and inputs, separate pins for limit switches , 2 relays, Ethernet and USB interfacing.

What breakout board do i need for the mach4 software?

• What breakout board do i need for the mach4 software?

You can find the cnc machine interface board here that works with Mach4:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

This board will work with Mach3 and Mach4. The board is filled with a wealth of options and features, including the ability to connect up to 8 axes (motor drivers), pendant, LCD, many outputs and inputs, separate pins for limit switches , 2 relays, Ethernet and USB interfacing.

What breakout board do i need for the mach4 software?

• What are all the pin mappings for the 3d printer board?

Are you referring to the 3D Printer Main Board?

Diagrams for the 3D Printer Main board are located here: https://www.buildyourcnc.com/item/3D-Printer-Component-electronicsAndMotors-3d-printer-mainboard-FDMElectronics-3dprintermainboard

The linked diagram is too course to see where every trace goes. What is needed is something like
Dxx = x step
Dxx= y step
Etc... For the entire board.

What are all the pin mappings for the 3d printer board?

• What are the jumpers used for on the c-10 breakout board

The USB is only used for powering the parallel breakout board.

What are the jumpers used for on the c-10 breakout board

• What are the jumpers used for on the c-10 breakout board

endmill-singleflute
endmill-twoflute
endmill-compression
carveandengrave
endmill-surfacing

What are the jumpers used for on the c-10 breakout board

• what are the system requirements for the Linux CNC (EMC2)?

The Linux CNC (EMC2) does not require a high performing computer. This application will run fine on a Pentium or later computer system. You will need a parallel port as either part of the motherboard, or as an adapter that plugs into one of the motherboard PCI slots.

20

what are the system requirements for the Linux CNC (EMC2)?

• The plans/hardware option for the greenBull includes what?

The plans/hardware/electronics/mechanical includes everything but the wood structural components that can be cut by the customer. This plans/hardware option includes all of the electronics, like motors, drivers, controller, and all of the cables and wires to connect all of the electronics together. The mechanical components include shafts, couplings, linear rails, bearing blocks, sprockets, lead screws, etc. The hardware consists of all of the screws nuts, insert nuts, cross dowels, etc, to assemble all of the structural, mechanical, and electronics together.

The plans/hardware option for the greenBull includes what?

• What size forstner are used in the book build your own cnc

That was a very long time ago, but I think I was using 3/4". You can use a size just larger than the outer width of the nut.

What size forstner are used in the book build your own cnc

• what are the table dimensions for 4' by 8' heavy duty greenbull?

Actual table dimension: 4'x8' is 56.078"x 121.50" (the overhang in the illustrations should be 3/4" thick)
To determine the frame dimensions, first consider using the frame height shown of almost 3' (2.86'). The width of the frame should be 4" narrower than the dimension from rail edge to rail edge (6X rail to rail is 80.078"). This will provide a 2" overhang on both sides (4X frame width should be 56.078").
The length of the frame should be 4" shorter than the desired length of the rails to provide a 2" overhang on both ends. The travel length will be 20" shorter than the rail length due to the space occupied by the gantry sides.
Two long pieces of 3/4" material will need to be placed on top of the frame with the 2" overhang on the sides and the end. These long strips of material will receive the rails and the chain mounts on the ends.

https://www.buildyourcnc.com/Item/cnc-machine-greenBull-v4-4X

what are the table dimensions for 4' by 8' heavy duty greenbull?

Get Help with:
This Product
Orders
Tech Support
Sales
This Product
Order Query
Tech Support
Sales