Yes, the CNC machine hardware and plans combo is the same machine as in the book. The machine that we provide the plans for, can be found on the website, here http://buildyourcnc.com/Item/cnc-machine-scratchbuild

Additional Information:



Additional Information:

Click the link to add information to this solution:
IS THE CNC MACHINE HARDWARE & PLANS COMBO SHOWN AT LINK YOU LISTED SAME DESCRIBED IN BOOK?

We do not offer any free plans. We offer the CNC Scratch Build Kit which includes plans to build a CNC machine from scratch. You can find more information about this by clicking on this link https://buildyourcnc.com/cnckitintro.aspx

Additional Information:
WTF!! It says right on your utube page free plans available. I'll paste it from Utube right here.(DIY CNC Router for Under $900 - Free Plans Available) Very misleading, I spent a lot of time looking for this stuff and am lucky I found this because apparently none of its available for free. Very misleading, dishonest sales tactics. I'm sure you've made money conning honest people out of there money but your not gonna get shit from me. After reading what other people here have written, and the fact that you lie about the cost, at least on UTUBE, It is clear your a liar and a piece of shit. carry on though by all means and continue making money being a liar.

Additional Information:
So maybe you should edit your YT post that says you DO have free plans?

Click the link to add information to this solution:
I was told you have some free CNC machine plans. I can't find them. Where are they?

The blackfoot requires a total of 50 feet of cable.

The X axis needs 15 feet
The Y axis needs 17 feet
and the Z-axis needs 18 feet

These are 20 gauge 4 conductor cable.

Additional Information:

Click the link to add information to this solution:
WHAT CABLE LENGTHS SHOULD USE FOR THE BLACKFOOT CNC MACHINE

All of our machines that are offered as a kit do not have a plans option. We do have a machine that is build form plans. The plans refer to the scratch build machine: http://www.buildyourcnc.com/cnckitintro.aspx and the one in the book "Build Your Own CNC Machine": http://www.buildyourcnc.com/Book.aspx

Click the link to add information to this solution:
Do you have a CNC machine plan available for a 4'x8' machine?

You can determine the cost of shipping the greenLean or any other product to your country by adding the greenLean option to the cart. In the cart, click on the calculate shipping button and the shipping costs will be presented directly from the carriers that we use. You will also see the number of packages and weights of the packages in the cart, under the items in smaller print. Make sure that your shipping address is entered in the form prior to clicking on the calculate shipping button.

Click the link to add information to this solution:
I am looking at the greenLean cnc machine 4'x8' Vertically Oriented CNC. I am based in the UK. What sort of shipping costs would we be looking at?

These files are no longer available. We suggest purchasing a kit, like the blackToe, or blackFoot as these kits are far more rigid and perform much better.

https://www.buildyourcnc.com/blackToe2x4v40.aspx

https://www.buildyourcnc.com/Item/cnc-machine-blackFoot-v4

Additional Information:
20

Additional Information:

Click the link to add information to this solution:
Would you be able to provide .DWG/.DXF files instead of .NC files for the CNC Routing Machine Kit Version 1.3 please?

Yes, you can send your electronics to us for repair, or retrofit to work with either Mach3, Mach4 or LinuxCNC. You can send us an email at customerService@buildyourcnc.com to set up your appointment.

Some of the types of CNC electronics we will consider.

- We will work on electronics from other manufacturers as long as you are ok with the Mach3, Mach4 or LinuxCNC control software for your CNC machine or CNC router.

- We will repair or retrofit used CNC electronics.

- Some customers find that electronics are overwhelming to put together so we will finish these electronics wiring and assembly for you.

The cost for these includes labor cost for the time it takes to finish the CNC electronics repair or retrofit and for any parts that need to be replaced or added.

Here is an example of CNC electronics that we worked on for a customer:

Click the link to add information to this solution:
Can you repair the electronics on my CNC machine?

Our machine that matches those dimensions, the blueChick, uses roller chain for both X and Y axes, and a 1/2" 5 start 10 TPI lead screw for the Z axis. The precision is generally related to repeatability and we have not does extensive measurement of these tolerances. The resolution is set at better than 1000 steps per inch.

Here is the link for the blueChick:
https://www.buildyourcnc.com/blueChickVersion42CNCMachineKit.aspx

Click the link to add information to this solution:
What precision do the CNC machine have, for instance the 12’’ x 36’’ x 3’’?

Yes, we have a 4 axis combo kit available under Motion Electronics.

Click the link to add information to this solution:
Can you supply an electronics package for a dual x-axis CNC machine (X, Y, Z)

The book design uses all NEMA 23/24 motors which can be found here:
https://buildyourcnc.com/item/electronicsAndMotors-3axis-425-elcombo

I recommend the Mach3 USB option as you will be able to use the USB connection for control.

If you are planning to build from the plans developed by the folks over at Woodsmith Magazine which is loosely based on the book design, use this electronics package:
https://buildyourcnc.com/item/electronicsAndMotors-3axis-heavy-gantry-elcombo

Click the link to add information to this solution:
Which electronics package is required for the CNC machine from the book designs?

Yes, the CNC machine hardware and plans combo is the same machine as in the book. The machine that we provide the plans for, can be found on the website, here http://buildyourcnc.com/Item/cnc-machine-scratchbuild

Additional Information:



Additional Information:

Click the link to add information to this solution:
IS THE HARDWARE AND PLANS MACHINE SAME AS BOOK MACHINE?

The eyebolts are used in the squaring of the machine. I would use a standard carpenters square and first run the end mill along the edge of the square to first make it parallel with the long axis. Then run the end mill along the other edge with the short axis and adjust the eye bolts and chain according to the angle that the machine is out of square.

Additional Information:

Click the link to add information to this solution:
DO NEED TO SQUARE UP THE MACHINE AND IF SO YOU HAVE INSTRUCTIONS OR VIDEO FOR THIS?

You can use the board5.nc as the expansion parts.

Additional Information:
20

Click the link to add information to this solution:
Where is the link for the expansion kit for the CNC Routing Machine Kit Version 1.3?

You can determine if the country is serviceable by:
- selecting the items you want to purchase on the website
- go to the cart (shopping cart top left of any webpage)
- log in, or register
- Enter the address and click on calculate shipping.

The webpage will return the direct rates and whether your area is serviced or not. Feel free to enter any address as long as you are able to receive the package from that address.

The shipping times are determined by the service you select in the shopping cart. If a machine is purchased, we generally have a one week lead time unless otherwise stated in the description of the machine's product page.

Additional Information:

Click the link to add information to this solution:
What is your shipping costs for the greenLean CNC machine to Perth Western Australia

The greenlean requires 56 feet of 1/4 Inside Diameter and 3/8 Outside Diameter silicon tube for the spindle.

Additional Information:
20

Additional Information:
20

Click the link to add information to this solution:
HOW MUCH SILICONE TUBE DO I NEED FOR A GREEN LEAN TO CONNECT THE SPINDLE

Yes, the greenLean can do the same type of machining as any other 3 axis CNC machine or CNC router. With 3D machining using a 3 axis CNC machine, 3D carvings can be done; however, no undercuts can be carved as the end mill (carving tool) is constantly perpendicular to the workpiece.

A 4th axis headstock and tailstock can be added to the machine for more precise 3D carvings and the greenLean can have these 4th axis units mounted within the structural ribs.

Click the link to add information to this solution:
Does the Green lean CNC 4'X8' cut 3D?

Thanks for the kind words. The kit is available for those that want the parts to assemble the case which comes with the computer parts. If you don't need the computer parts, let me know and I will offer the bare bones without the computer system.

Previous Solution:
I already have a DIY CNC machine with all my electronics but I have two cases the size of a mid tower PC and was looking to shrink the weight and footprint of all of them. I understand if you don't have plans available, I just really loved the design and compactness of your case.

Previous Solution:
The redLeaf and redSprout boxes are meant to provide enclosure to the systems that we assemble in-house for customers that prefer a complete plug and play system. We provide the kit of parts for the enclosure from overwhelming customer request. There are no plans available for the enclosure and the complexity of the parts needed to be fabricated is quite high where the task of cutting out all of the intricate parts by hand would be a larger investment in time and materials than the cost to purchase the kit.

Additional Information:
Just curious at what you would sell the box itself empty or the dimension files for the box for?

Additional Information:



Additional Information:

Click the link to add information to this solution:
DO YOU GIVE AWAY THE PLANS FOR REDLEAF/REDSPROUT BOX?

Thanks for the kind words. The kit is available for those that want the parts to assemble the case which comes with the computer parts. If you don't need the computer parts, let me know and I will offer the bare bones without the computer system.

Previous Solution:
I already have a DIY CNC machine with all my electronics but I have two cases the size of a mid tower PC and was looking to shrink the weight and footprint of all of them. I understand if you don't have plans available, I just really loved the design and compactness of your case.

Previous Solution:
The redLeaf and redSprout boxes are meant to provide enclosure to the systems that we assemble in-house for customers that prefer a complete plug and play system. We provide the kit of parts for the enclosure from overwhelming customer request. There are no plans available for the enclosure and the complexity of the parts needed to be fabricated is quite high where the task of cutting out all of the intricate parts by hand would be a larger investment in time and materials than the cost to purchase the kit.

Additional Information:
Just curious at what you would sell the box itself empty or the dimension files for the box for?

Additional Information:



Additional Information:

Click the link to add information to this solution:
DO YOU GIVE AWAY THE PLANS FOR REDLEAF/REDSPROUT BOX?

The available options for the blackFoot, is only structural components with hardware, and structure components/hardware with electronic components.
However we currently do not have any plans available for public use/distribution.

Click the link to add information to this solution:
Do you provide plans and/or parts to build the blackFoot CNC table?