Yes, you can absolutely communicate with the Pokeys57CNC controller. The developer's website has various ways of control, including their poblock software, or directly programming using C#, or C++. I have tested the C# method for a job I did for Lockheed Martin and worked really well.

Click the link to add information to this solution:
[596] Hi there! Thank you for your great works. I was wondering if there is a way to communicate with this board using custom-developed software instead of Mach3 or Mach4.

Our electronics and plug and play systems can be used with any industry standard software, including but definitely not limited to the Vectric line of software.

Click the link to add information to this solution:
I am getting ready (within a week) to purchase your lug in play controller kits... The software I want to use is Vectric. I notice you talk about Mach software and sketch up. Be fore I purchase I want to make sure I can use what ever software I want... Thank you for your time. Pam

You will need a CNC software that will control your router cnc machine, and your design CAD/CAM software will need to know the CNC software you plan on using so the post processor in the CAM software can create the g-code for the CNC control software. So if you have for example, Mach 3 and our parallel breakout board, you can use the Mach 3 post processor in your design software.

Click the link to add information to this solution:
I'm new to CNC and just finish building my router.I need software for my post processor and not sure if your product is what I need?

The usual travel time overseas, takes around 1 week to 3 weeks depending on the carrier and service selected.

Click the link to add information to this solution:
Regards   I hope to know the time it takes for shipping by USPS Priority mail international to Jeddah in Saudi Arabia Thank you

The usual travel time overseas, takes around 1 week to 3 weeks depending on the carrier and service selected.

Click the link to add information to this solution:
Regards   I hope to know the time it takes for shipping by USPS Priority mail international to Jeddah in Saudi Arabia Thank you

The usual travel time overseas, takes around 1 week to 3 weeks depending on the carrier and service selected.

Click the link to add information to this solution:
Regards   I hope to know the time it takes for shipping by USPS Priority mail international to Jeddah in Saudi Arabia Thank you

Generally, you’ll need to check what control software will need to be used with the CNC router. Our machines use industry standard electronics and control software that is nonproprietary so you can use just about any software out there with our machines.

Specifically, what software are you planning on using?

Additional Information:
dear Sir,
I'm searching for the best one,I think that I have to learn more about that in order to be able to make the right decision.

Additional Information:
If you are using a computer running Microsoft Windows, then I would recommend using Mach3 or Mach4. If you prefer Linux, then LinuxCNC is the best control software in my opinion.

Click the link to add information to this solution:
I'm searching for a desktop cnc, could you tell me please if any software I may choose could be compatible with all desktop cnc machine or I have to check the compatibility before ?

if you purchased the USB interface, you will need planet-cnc software rather than Mach3, and you will need a usb cable to connect the usb interface to the computer.

The blackToe 2x4 CNC Machine Kit with optional table will need wire to connect the electronics. Don't forget to get some end mills to use for cutting the intended material.


Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
If I purchase the [blackToe 2x4 v4.1 CNC Machine Kit - USB Electronics - Table Included] all I would need for this CNC to be fully operational is a laptop with mach 3 software and a router. Is this correct?

You can find instructions for the Mach3 USB here:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

You will probably need to use the Mach3 USB board with Mach3. We have not tested the Mach3 usb card with Mach4.

Click the link to add information to this solution:
Whereb can I find directions on how to install the Mach3 USB board with Mach 4 software? I do not have a parallell port.

The greenLean vertical CNC is stable enough to handle large-scale production on a daily basis. We use 3/4" MDO plywood, which is equivalent to about 19mm. The gantry is designed to hold a 2.2kW Spindle, with a maximum of 24,000 RPM.

Click the link to add information to this solution:
Hello. I like your vertikal router. Is then router stabil enogh for the need of a Carpenter? Are you using 21mm Plywood or 21mm MDF. What type of spindel (KW) is maximum allowed and whatbis the maximum feed (6mm cutter) in oak. Thank you, Veit

Your question caused me to make a quick video to understand how the pokeys57CNC controller works with a THC.

Click the link to add information to this solution:
[596] Would you help with the Hook up and the Configuration and whether it is in the Plugin or mach 4 control configuration that needs to be set. I decided to use the ultra fast encoders connector pin #8, 12 and 13 for Arc ok, UP and Down. Please advise what setting to set to make it all work. Thank you very much for your help!

BYCNC Response:
This is correct. You will need to use a method appropriate for the software you are using. Also remember that NC switches are typically wired in series, while NO switches are normally wired in parallel.

User Response:
I am using the cnc planet software for your USB board. Are the limit configurations in this software?

BYCNC Response:
Yes, Planet CNC software is compatible with the use of limit switches. Configuration information will depend on your specific application. You can view Planet CNC's information here: http://www.planet-cnc.com/files/CNCUSBController.pdf

Click the link to add information to this solution:
LIMIT SWITCHES FOR AXIS. THE PRINT SHOWS THAT YOU CAN WIRE LIMITS EITHER N.O. OR N.C. SO IF THIS IS CORRECT I WOULD NEED TO TELL BOARD IN SOFTWARE HOW LOOK AT THESE LIMITS, I'M GOING GET AN INPUT LOOSE DEPEND ON IT.

You will need to look for the parameter that controls the run frequency. The frequency can be controlled bu the panel, external terminals, or the RS485 TX/RX terminals (UART protocol). You will want to change that parameter so it uses the panel. If you are referring to the maximum panel dial frequency is only allowing 200-300 rpm, then look for the parameters to control the frequency.

For 200 RPM:
Hz = 200/60 = 3.33 Hz

For 300 RPM:
Hz = 300/60 = 5 Hz

Conversion to RPM:
If you ever find yourself yearning to reverse-engineer the process, the formula is as follows:

RPM = Hz × 60

Look for values that match somewhere between 3 and 5 in your frequency parameters and replace them with 400 to give you 24,000 RPM max.

Click the link to add information to this solution:
[77] Hello. I’m interested in buying a water cooled spindle and VFD. I have an Avid Pro CNC and would love to control it using Mach 4 but I keep hearing it’s difficult to integrate. Also, is the water pump 120 or 240? I’d love any advice etc. eBay is a web of confusion with all of the options. Thank you.

Currently our USB breakout board is only compatible with Planet-CNC software as it has to be registered with Planet-CNC.

Click the link to add information to this solution:
Hi, I have watched your vids on YouTube and I am interested in purchasing one of your USB Break-Out Boards. I currently own and use FlashCut CNC software, which is USB based, on all of my machines. I'm wondering if you could tell if the Flashcut software will talk with the USB Break-Out Board? Thank You

Yes, you can send your electronics to us for repair, or retrofit to work with either Mach3, Mach4 or LinuxCNC. You can send us an email at customerService@buildyourcnc.com to set up your appointment.

Some of the types of CNC electronics we will consider.

- We will work on electronics from other manufacturers as long as you are ok with the Mach3, Mach4 or LinuxCNC control software for your CNC machine or CNC router.

- We will repair or retrofit used CNC electronics.

- Some customers find that electronics are overwhelming to put together so we will finish these electronics wiring and assembly for you.

The cost for these includes labor cost for the time it takes to finish the CNC electronics repair or retrofit and for any parts that need to be replaced or added.

Here is an example of CNC electronics that we worked on for a customer:

Click the link to add information to this solution:
I would like to use Mach3 instead of the software for my CNC router. Can you fix the electronics for me?

Yes, servo motors can be mounted on this machine. If the mounting dimensions are different than NEMA 23 or NEMA 34, then all you need to do is keep the center of the motorshaft with the center of the bearing location and locate the mounting holes for he servo you wish to use. Most industrial servos used for these machines share the same mounting dimensions and NEMA specifications.

Additional Information:
This machine is one of the most customizable machines out in the wild. Customers of these machines have fashioned many modifications to suit their needs.

Additional Information:
20

Click the link to add information to this solution:
[796] Hello. To what extent can the design plans be customized? For example, if I wanted servo motors instead of steppers? That would requirements for motor mounting, controls, and electrical. Thank you.

All of our CNC machines can carve at that depth without a problem and do 3d carving. Our typical application is cutting sheet materials, but a good percentage of our customers cut 3D bas reliefs or even more complex 3D objects using reference points and jigs.

Most of our CNC machines have a Z travel of at least 6 inches for the smaller machines and 7 to 10 inches for our larger machines. The Fabricator Pro has a Z travel of 10 inches.

Depending on your application, you will need to consider the length of the end mill (more than the deepest depth of the 3D carving) and the stock that you will be using. If the stock plus the length of the end mill exceed the clearance with the Z axis raised to the top extent, then you will need to consider the way the table/bed of the machine is formed (maybe with a depression to take advantage of the greater need for clearance).

The greenBull has the capability of Z axis travel of up to 36 inches, but I would recommend, if milling wood, that the Z-axis not extend more than 12 inches to reduce deflection.

Additional Information:
Most of the CAM software on the market will have 3D profile machining operation capabilities. CAMBAM has a very nice 3D prpfiling feature. The Vectric line of software can definitely handle this as well.

Click the link to add information to this solution:
All of the pics and videos show your cncs cutting sheet materials, I'm interested in carving 3d images in plastic and hardwood slabs up to 2" thick. What machine and software would you recommend?

The bluchick CNC router is a perfect small format CNC that can handle most jobs. Please check here to see the latest information on this CNC router. blueChick CNC Machine. The machine can be purchased assembled. Al you will need is a computer and spindle.

Click the link to add information to this solution:
I'm looking for a complete CNC router, out the box ready to use system. Computer and software. What do you suggest? I need a working area of 12"x24"

Here is the new link to the Planet CNC software download page: http://planet-cnc.com/software/

You can try the software as a demo however you will have limited g-code lines you can run. I believe it was around 500, so you can create small items with the demo.
To fully unlock the Planet-CNC software you will need to purchase the license.

Click the link to add information to this solution:
I purchased the USB BOB and the link for the Planet-cnc software is broke. Will I need to purchase a license for the software as well?