The instructions on how to do this are found here, in these two videos, http://buildyourcnc.com/PrimeronHomingandLimitSwitches.aspx

Additional Information:

Click the link to add information to this solution:
HOW DO I CONNECT A TOUCH PLATE TO THE BREAKOUT BOARD?

If the motor has 8 wires, you will need to wire the stepper motor in bipolar parallel. This motor (425 oz-in) is wired as follows:

Red and Blue wires to A+ on driver
Yellow and Black wires to A- on driver
White and Brown wires to B+ on driver
Orange and Green wires to B- on driver

Click the link to add information to this solution:
[54] There are 8 wires on this motor. How do you connect to the driver?

CP+ to COM
CP- to STEP
CP+ to CW+ (small jumper wire)
CW- to DIR

Additional Information:
If the driver does not have CP or CW labels, the CP is Step and the CW is Direction or DIR. If you connect the 5v to CP+ (or Step+) and CW+ (or DIR+) and the pin to CP- (or Step-) and another pin to CW- (or DIR-), then in software, the configuration for the step on that axis must be active low. Otherwise, if you connect the GND to CP- (or Step-) and CW- (or DIR-) and the pin to CP+ (or Step+) and another pin to CW+ (or DIR+), then in software, the configuration for the step on that axis must be active high.

Additional Information:
If you have a driver that is labeled pul, dir and ena: Pul+ is the Step+ and Pul- is the Step-. Pul is short for pulse. A pulse will create a step. Don't worry about the enable terminals.

On the x-axis, pin #2 can go to pul- and pin #3 can go to dir-. The 5v will go to pul+ and dir+. The configuration for each axis for step will be active low and toggle active low for the dir on each axis to make it go in the direction desired.

Additional Information:


Additional Information:


Additional Information:


Additional Information:

Click the link to add information to this solution:
HOW DO I WIRE FROM THE BREAKOUT BOARD TO DRIVER?

The parallel breakout board has the db25 connector for data and the USB connector for power. Connect the USB from the computer to the parallel breakout board so the breakout board will have 5V of power coming from the computer. The db25 connector (connector with the 25 pins) receive data signals for each pin from 1 to 17 and have respective numbered screw terminals, some for input and some for output (18 to 25 are gnd pins).

Click the link to add information to this solution:
Should I connect both the USB and the 25 pin connector of the parallel breakout board to the computer?

This controller does not have an encoder input to determine the speed of a lathe spindle. The Pokeys57CNC does have an available encoder input.
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Click the link to add information to this solution:
[575] how do i connect a lathe spindle speed encoder to this usb breakout board controller so i can set up for thread cutting on my lathe and on the mill for threading

Polabs prepared step by step user guide for PoKeys57CNC and Mach4 to try answering such questions. It is available in our downloads section: https://www.poscope.com/wp-content/uploads/downloads/Pokeys/LibrariesAndPlugins/Mach4 and PoKeys57CNC - step by step guide.pdf

Additional Information:

Click the link to add information to this solution:
Using the PoKeys57CNC how to you connect two motors to the Y axis and how is Mach 4 configured for this?

The breakout board does not require software to run, specifically. The breakout board serves only as a signal conditioner where the input signal from the computer is output at the corresponding terminal, or the terminal receives a signal and is conditioned and sent to the parallel connector to be read by the computer. As long as the software can communicate to the parallel port of the computer, then the breakout board will function.

Click the link to add information to this solution:
Do the 5 Axis Breakout Board with Relay requires software to setup

Do you have a TL or a TH for triggering the laser? If you power the digital side of your laser power supply with 12V and tie the gnd with the PWM gnd on the pokeys57CNC controller, you may be able to use the PWM on the pokeys57CNC controller. Before you do this, I would suggest that you contact polabs support (http://support.polabs.com/) and ask them if this is possible.

Click the link to add information to this solution:
Using a Pokey57 CNC and Mach 4 can you tell me how to connect my laser. The laser has three wires.. Ground - 12V Power and PMW.

From the USB controller, the CP+ and CW+ are connected to the 5V terminal. The CP- is connected to the CP terminal of the driver and the CW- is connected to the CW terminal of the driver.

Additional Information:

Click the link to add information to this solution:
Please explain how to connect 2.5AMP stepper motor driver to USB board. All parts are from your store. Thanks

The USB port located on the parallel 5 axis breakout board is for powering the board. There is no communications related to this port.

Click the link to add information to this solution:
What is the usb port for on the 5 Axis Breakout Board with Relay ($28.50)?

Yes, you can control the speed of the 2.2 kW spindle, and the other spindles we sell, through Mach3 software. It requires making some changes to the settings in Mach3 and in your inverter. It also requires an additional part, which is called a USB to Serial Converter, found on our site here:

https://www.buildyourcnc.com/item/Interfaces-newbiehack-Interfaces-TTL232R-USB-UART-Serial

I have some additional instructions, that I will send upon request, by email. I will also be adding a complete tutorial and video, to the website, on how to do this soon.

Additional Information:
20

Click the link to add information to this solution:
can I control the speed of a 2.2 spindle through your 5 axis breakout board with relay?

The DRV8825 driver IC by TI (Texas Instruments) has two main connections called STEP and DIR. These are the two main connections that you need to use to connect to the Pokeys57CNC controller. You also need to connect the positive digital voltage pin (5V) from the Pokeys57CNC controller's motor connector to both the reset and sleep pins. The GND pin from the Pokeys57CNC motor connector is connected to the GND pin of the DRV8825 driver. The enable pin of the DRV88525 can remain unconnected.

There is a trimmer potentiometer on the DRV8825 that can increase or decrease the amperage setting for the motor. Depending on the DRV8825 board you purchased, there may be two pads to determine the amp setting while turning the trimmer (in the voltage setting on your multimeter).

The A1 and A2 is connected to one of the motor's coils and B1 and B2 is connected to the other motor's coil. There is a pin on the DRV8825 called VMOT that you will connect to the power supply (max 45VDC) and the GND pin next to the VMOT is the V- for the same power supply.

I hope this helps. If not, please add additional information on this thread.

Additional Information:
I followed (to the best of my ability) the instructions provided to my original question, but I did not receive successful results. When I followed the instructions and connected the ground pin from the Pokeys57CNC motor connector to the DRV8825 / A4988 expansion board, it stops the communication between the Pokeys57CNC board & the motors 1-3 that I had working previously. The DRV8825 / A4988 expansion board will be the fourth driver I am connecting to the Pokeys57CNC. The previous three drivers are PoStep-60's if that helps understand the issue.

Prior to hooking up the ground pin (I used pin 10 from the Pokeys57CNC motor connector) to the DRV8825 / A4988 expansion boards ground pin, I was able to see the power being applied via the red LED being illuminated on the DRV8825 board; after this new configuration the light is not turning on.

With the new recommended setup, I used a heat shrink solder piece to add the shunt for the connection to the sleep pin. The connection to the sleep pin is where I believe my issues are stemming from. I must be connecting it to the incorrect pin (within the 9 pin layout on the DRV8825 / A4988 expansion board). Do you have any reference to the 9 pin pinout on the A4988 expansion board? I double checked the pinout provided on the Texas Instruments page, but it only gives clarity to the pinouts on the DRV8825 board itself. After reviewing their documentation, I tried connecting the 5v (pin 9 from the Pokeys57CNC motor connection that's split to connect with the reset pin on the DRV8825 / A4988) wire directly to the terminal on the DRV8825 board and that didn't work either.

Any help or clarification you can provide would be greatly appreciated!

Click the link to add information to this solution:
How can I connect the Pokeys57CNC controller to a DRV8825 / A4988 expansion board?

The greenlean requires 56 feet of 1/4 Inside Diameter and 3/8 Outside Diameter silicon tube for the spindle.

Additional Information:
20

Additional Information:
20

Click the link to add information to this solution:
HOW MUCH SILICONE TUBE DO I NEED FOR A GREEN LEAN TO CONNECT THE SPINDLE

Have you tried a different input pin?

Customer response:
I've tried all pins: 10, 11, 12, and 13. I get the same non-response in each case.

Recommended action
There may be a problem with the board. If you are using our parallel breakout board, we can ship you a replacement (call us), otherwise, you will need to determine the problem with the vendor of the breakout board you are using.

Additional Information:
I have tried 3 different breakout boards from 3 different providers and they all do the same thing My limit switches are microswitches wired NC with each axis wired to the BO Board. I have checked each circuit and all is OK to the BO board. each circuit has continuity at the board and when any switch is pressed the circuit breaks. Mach 3 does not recognise that the switches are even there. They are configured as active low Do you have a suggestion.

Additional Information:

Click the link to add information to this solution:
I'm having trouble getting Mach3 to recognize my limit switches. I've eliminated everything back to the breakout board. I can directly connect Input 10 to GND on the breakout board while Mach3 is in autorecognize mode and Mach3 doesn't acknowledge anything.

The datasheet for the parallel breakout board is here:
https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay#prettyPhoto/2/

The datasheet for the USB interface is here:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-USB-Controller-Breakout#prettyPhoto/2/


Additional Information:
20

Click the link to add information to this solution:
I need wiring instructions for the breakout board you sent yesterday. It is not like the one in the videos and I don't know where to connect the 5V. No data sheet or anything.

The Pokeys57cnc board: https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

This board contains a 0-10V output at pin #17 that can be connected to the spindle's VFD 0-10V input. On the VFD, this terminal is typically called AI0 or above.

Pin #14 on the Pokeys57cnc board can also be used as a spindle error input.

The Galvanically isolated I/O section of terminals on the Pokeys57cnc board (which also contain the pins 14 and 18, can be used to serve as the on/off for the spindle/VFD using the VFDs digital input.

Additional Information:

Click the link to add information to this solution:
How do you wire the connection between the vfd and the pokoys57cnc breakout board?

If your computer does not have a parallel port, all you will need is a low cost PCI parallel adapter card (these can be found on amazon for $15-$20). If you plan on using a laptop (not recommended) you can try to find a PCMCIA parallel adapter, but many people have frequent issues with this setup. A more expensive solution would be to purchase a USB smooth stepper board. Unfortunately, we do not supply any of these adapters and cannot attest to their reliability.

Additional Information:
ur gay

Additional Information:

Click the link to add information to this solution:
MY COMPUTER DOES NOT HAVE A PARALLEL PORT. HOW DO I INTERFACE WITH THE BREAKOUT BOARD?

Have you watched this video by any chance?

Click the link to add information to this solution:
Could you please tell me how to wire the pokeys57 and driver DM860T or gecko driver ??

CO2 laser will not cut wood material fast at all. This is just the nature of the laser energy. The wood is a very low absorbent of the laser energy and you will need to run probably around 10 ipm to cut through the wood. CNC is much more efficient for cutting and laser as more efficient at marking or slowly cutting if you need the small kerf. You will also need a relatively high output air source to cut efficiently. The air will blow away the char (carbon) on the wood. The black char will absorb most of the laser energy not allowing the wood to be cut well. We use a compressor for the air source, but you can use a commercial hydroponic air pump instead.

Click the link to add information to this solution:
How fast can I cut 1/4" wood with the 40 watt CO2 laser?