If your motors are hot to the touch, this is normal. Current is being drawn by the motor coils as the motor moves and as the motor stays at a position. If the motor is not using the current in the coils to move (holding it's position), the energy will be translated as heat (rather than motion, sound or light). Even while moving, some of the energy will be lost as heat. Remember that energy cannot be created nor destroyed.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
I HAVE FOLLOWED ALL THE "CNC ELECTRONICS 1 - 9" VIDEOS AND I'M USING ALMOST EXACT SAME COMPONENTS (MOTORS RUN SOUND GOOD) BUT MOTORS ARE RUNING VERY HOT IN JUST 15MIN WITH NO LOAD DONE SOMETHING WRONG OR DO STEPPERS HOT?

You can purchase the entire length and select local pickup. Then you can email us the cut lengths for the order and let us know that you need to be invoiced for shipping. We will provide shipping estimates according to the real lengths and dimensions of the package. You can select the estimate that meets your shipping budget and we will invoice you the shipping amount and send the order.

Click the link to add information to this solution:
Hi I built a 2x4 cnc machine in 2013 using you Hardware kit and plans. I want to speed up my cnc machine by purchasing your acme leadscrew 1/2"-10 5 starts. I have an X axis at 52", a Y axis at 32" and a Z axis at 14". How do I order all 3 length pre cut to size on your website? Also can you give me a rough estimate on the shipping to Ottawa, Ontario Canada please.

The connections between the driver and the breakout board(USB/Parallel)22-24 AWG wire is preference also going from the potentiometer going to LSPS(laser power supply) , now going from the power supply to the drivers/laser power supply 16-18 AWG wire is our preference.

Click the link to add information to this solution:
I'm about to order your laser cutter , item 279 and a little confused.. in your faq it states you need wire and connectors for assembly, can you be specific on amount and guage of wire or tell me where to find that information?

The leadscrew length for the greenBull long Z-axis is 47 inches.

Additional Information:

Click the link to add information to this solution:
Building one of your greenBull 6X Long and 2.2 kilowatt spindle does not fit. Seems lead screw you sent with kit is short 42" looks like it needs to be 5 or 6 inch longer. Is this correct? What is the needed length of lead screw for this unit?

The mxl 0.08" pitch is fine for moving the weight of a gantry that contains a 40 watt laser tube and optics. I would not advise this timing belt for CNC applications that need to move heavy items such as spindles, routers, and heavier structures that are required to move these spindles and routers around.

The mxl 0.08" pitch timing belt is also great for 3d printers.

Click the link to add information to this solution:
Originally bought the Blacktooth Laser kit, but the upgraded laser tube size and needed a larger casing. With that I need to upgrade the belts to a 36" run. Can you advise whether the mxl.08" timing belt is sufficent or do I need the .2"in.

We will contact you with a list of options.

Click the link to add information to this solution:
I would like to upgrade my older engraver to usb or parallel port i want to build as much of it as possible to cut down on expense. The name of the engraver is New Hermes vanguard 4000 the specs can be found on the internet. Looking to purchase parts today please contact me at 937-262-8446 or email me at isaacjcrawford@sbcglobal.net with the information and part numbers thanks.

The leadscrew length for the greenBull long Z-axis is 47 inches.

Additional Information:

Click the link to add information to this solution:
BUILDING ONE OF YOUR GREENBULL 6X LONG AND 2.2 KILOWATT SPINDLE DOES NOT FIT. SEEMS LEAD SCREW YOU SENT WITH KIT IS SHORT 42" LOOKS LIKE IT NEEDS TO BE 5 OR 6 INCH LONGER. THIS CORRECT? WHAT THE NEEDED LENGTH FOR UNIT?

BYCNC Response:
This is correct. You will need to use a method appropriate for the software you are using. Also remember that NC switches are typically wired in series, while NO switches are normally wired in parallel.

User Response:
I am using the cnc planet software for your USB board. Are the limit configurations in this software?

BYCNC Response:
Yes, Planet CNC software is compatible with the use of limit switches. Configuration information will depend on your specific application. You can view Planet CNC's information here: http://www.planet-cnc.com/files/CNCUSBController.pdf

Click the link to add information to this solution:
LIMIT SWITCHES FOR AXIS. THE PRINT SHOWS THAT YOU CAN WIRE LIMITS EITHER N.O. OR N.C. SO IF THIS IS CORRECT I WOULD NEED TO TELL BOARD IN SOFTWARE HOW LOOK AT THESE LIMITS, I'M GOING GET AN INPUT LOOSE DEPEND ON IT.

Can you send me a link to the digitizer you are using?

Click the link to add information to this solution:
Hi my names is Minh Truong I would like to said thank you very much for your video I got the system mach3 working fine but one thing I can NOT set and config the digitizer on the board IN4 I am not sure how to setup because in the Mach3 pin 14 for digitizer Please shoe me hoe to set it up for the digitizer.

BYCNC Response:
Please send a photo of the bolts and assembly so we can determine the problem. Thanks.

User Response:
The holes on the Dremel holder are 0.442" and the bolt heads are 0.483". Picture will be sent. In the picture note that the left bolt has been ground down.

BYCNC Response:
You were sent incorrect fasteners due to a vendor change. We will be shipping the correct parts to you immediately, and thank you for letting us know about this mistake.

Click the link to add information to this solution:
I JUST RECEIVED MY WHITE ANT AND STARTED TO DO SOME BASIC ASSEMBLY. NOTICE THAT THE 1/4 X 20 BOLTS WITH PHILLIPS HEAD NOT FIT IN NOTCHES CUT FOR THEM - INSTANCE, ON DREMEL MOUNT. AM SUPPOSED BUY DIFFERENT HEADS, GRIND ALL DOWN, OR ROUTE OUT BIGGER NOTCHES. 3" BARELY Z-AXIS MOTOR

NC mechanical switch configuration is supported. You can download the manual from this page (Mach4 plugin and manuals):
https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

The pokeys57CNC controller has input terminals and pins for limit switches on each of the 8 axes. There are three separate inputs per axis, two for the actual limits of that axis, and one for the home position.

Connect each switch between the GND terminal and its respective axis limit terminal/pin. For instance, the limit switch will typically have three leads, COM, NC, and NO. In an NC configuration, the NC connects to the terminal/pin, say, Axis 1 lim +, and the COM connects to the GND terminal.

In Mach4, in the new device wizard, make sure to specify the correct option on the home and limit switches that matches the machine configuration.



Additional Information:
can you use one switch per axis for home only?

Click the link to add information to this solution:
Hello, I am trying to configure Home and Limit switches using the Pokeyes57cnc and NC switches. I am confused on the procedure of setting this up. wiring to the board and setting up in Mach4. Can you direct me to a tutorial or offer some suggestions? Thanks Dale

Yes, we can help you with leveling your CNC machine even if you didn't purchase it from us.

Click the link to add information to this solution:
[789] I need to level my cnc machine, but I didn't purchase it from you, so: Do you offer tech support with leveling a cnc? Because I don't see this problem listed .And: Do you offer support if my machine was purchased in China or from another vendor?

You will need to look for the parameter that controls the run frequency. The frequency can be controlled bu the panel, external terminals, or the RS485 TX/RX terminals (UART protocol). You will want to change that parameter so it uses the panel. If you are referring to the maximum panel dial frequency is only allowing 200-300 rpm, then look for the parameters to control the frequency.

For 200 RPM:
Hz = 200/60 = 3.33 Hz

For 300 RPM:
Hz = 300/60 = 5 Hz

Conversion to RPM:
If you ever find yourself yearning to reverse-engineer the process, the formula is as follows:

RPM = Hz × 60

Look for values that match somewhere between 3 and 5 in your frequency parameters and replace them with 400 to give you 24,000 RPM max.

Click the link to add information to this solution:
[77] Hello. I’m interested in buying a water cooled spindle and VFD. I have an Avid Pro CNC and would love to control it using Mach 4 but I keep hearing it’s difficult to integrate. Also, is the water pump 120 or 240? I’d love any advice etc. eBay is a web of confusion with all of the options. Thank you.

This turned out to be a side-effect of the "foot logo" now being bored entirely through the gantry legs. On first inspection this made the two legs identical. I didn't notice that the hole for the X axis axle was bored out to 5/8, but only on one side. Not too surprisingly, I installed them on reverse sides.

Pulling the legs off and swapping the side they were mounted on fixed the problem. I would suggest adding a note to the building instructions page to avoid this annoying problem.

On the good side, the X axis now rolls much more freely on its rails after un-mounting and re-mounting the legs.

Additional Information:
Good catch and thank you for the information. We will clarify this on the video.

Click the link to add information to this solution:
At 3:29 in the video "blackToe version 4 2x4 step 9 0001" it shows you inserting a bearing into the hole that the x axis shaft exits the router. That hole is 3/8ths on my parts. No 3/8 OD, 1/4 ID bearing came with my kit, but I do have a 5/8 OD, 1/4 ID bearing. Should I bore out the hole to 5/8 so I can insert those bearings?

Do you have an oscilloscope? You will be able to see the PWM signal and determine if the output is correct. Make sure that you are using the 10V from the VFD as the voltage reference for the 10V terminal on the Mach3 USB controller. The 10V terminal is an input, not an output on the Mach3 USB controller. The 10V is the top voltage signal level that the Mach3 USB controller uses for the PWM signals 100% duty cycle.

Click the link to add information to this solution:
[575] I have the wiring and programming and parameters set the same way that you do in the spindle speed control and outputs videos, I can start and stop the spindle with mach3 but can't seem to control the speed. Can you think of solutions?

If you have the USB controller you will need to purchase a USB controller license from planet-cnc.

Click the link to add information to this solution:
with the blueChick v4.2 can any software be used or doo we need to purchase a lic key from the manufacture of the control board for 75 bucks

The best machine due to the width, will be the greenBull 5x which would have a cutting surface of 5' x 10'. Also our machines with spindle are accurate for 1000's of an inch, and can do 45 degree angle cuts.

Click the link to add information to this solution:
I build custom speakers and I work primarily with 5'x5' sheets of 9 ply (1/2") and 13 ply (3/4") plywood, but I occassionally cut 2" nominal thick wood as well. What kit would you recommend? Are your systems accurate enough to do angle cuts (45 deg?) thanks

Absolutely, I can answer this type of question and anything other questions you may have with your new-to-you CNC router.

Additional Information:
20

Click the link to add information to this solution:
[789] Can you help me with selecting a power supply ( and a few other components ) for the stepper motors that came with a homemade CNC Router I just purchased.

Since the nozzle is getting warm, much of the laser energy is not exiting the aperture and is hitting the inside of the nozzle. You need to align the laser's final mirror to direct it out of the nozzle's aperture and you will have more than enough energy to cut 1/8" acrylic efficiently.

Click the link to add information to this solution:
I've been unable to cut through acrylic or wood at a thickness of 1/8" or less with the BlackTooth. Even with multiple passes (x10) and full power, a clean cut cannot be accomplished. Based on videos I've seen something doesn't seem right. I noticed that the nozzle gets very warm, almost untouchable during even short runs.