If you are located near Houston, Texas area you can stop by our shop. If you are not near us, you can check in our forums, and see if you can find someone in your area that has one of our machines, and would be willing to let you come see it in action.

Click the link to add information to this solution:
I WOULD LIKE TO KNOW IF THERE IS A STORE OR SHOP WHERE CAN SEE THE PRODUCT AND BUY IT?

The length of time it will take to build a CNC machine kit is not an easy answer. There may be a wide array of circumstances that limit a persons abilities to build the cnc machine kit in an efficient timeframe; however, if you have moderate dexterity and moderately mechanically inclined, you should have no problem building one of our machines within one weekend if the project has very little downtime.

Additional Information:

Click the link to add information to this solution:
HOW LONG WOULD IT TAKE FOR MY TO BUILD A MACHINE?

BYCNC Response:
The book build was intended to be 20 inches x 40 inches. Larger machines were designed after the book build was introduced so customers would have the option to go bigger than what the book offered. Check out our larger machines on the website as the machines sizes range from 1 foot x 3 feet all the way up to 6 feet x 12+ feet.

User Response:
I'm not wanting to spend $3,000+ on a machine, I want to build one that will do a 4x8 sheet of wood. Will the plans in the book scale up?

BYCNC Response:
It is possible to scale the book build up, but the rigidity of the gantry would be questionable at that span, even if the height of the gantry structure were to be increased. The gantry design would need to be modified to become a box shape rather than a flat configuration. The kits on the site were design for those wanting a larger machine.

Click the link to add information to this solution:
I BOUGHT YOUR BOOK AND WAS HOPEING IT HAD PLANS OR DIMENTIONS ON HOW TO BUILD A CNC HOLD 4X8 SHEET OF PLY. WILL THE IN SCALE UP?

The Federal Communications Commission (FCC) is the primary federal agency responsible for safety aspects of modern-day wireless telecommunications systems. The FCC's Internet address is shown below. Recently FCC published an excellent report, cited below, to assist citizens and local governments dealing with siting of telecommuncations towers. This report contains charts and figures describing the characteristics and performance of telecommunications antennas. The report also contains practical guidance on application of provisions of the Telecommunications Act of 1996, which is the governing legislation regarding safety and siting of wireless telelcommunications facilities. Web page: RF Safety Program Page. Report title: "A Local Government Official's Guide to Transmitting Antenna RF Emission Safety: Rules, Procedures, and Practical Guidance." The Local and State Government Advisory Committee (LSGAC) and the FCC have developed this guide to aid local governmental officials and citizens in understanding safety issues related to radiofrequency emissions from telecommunications towers. Gary Zeman, Sc.D., CHP Lawrence Berkeley National Laboratory

Click the link to add information to this solution:
I AM TAKING THE FINAL YEAR PROJECT IN BASE STATIONS AND AIR INTERFACE. WOULD LIKE TO HAVE SOME INFORMATION.

You will need to build the table unit for your machine. There are instructions on how to do this at the bottom of the product page here, https://www.buildyourcnc.com/Item/cnc-machine-blackFoot-v4
There is no estimate on how much this will cost though, since there are too many variables involved to do this.

- PC with parallel port and USB port
- 20awg stranded wires for the motors - http://www.buildyourcnc.com/electronicscombo.aspx
- 18awg stranded wires for power supply to drivers
- 24awg stranded wires for breakout board to drivers
(location and spacing of components varies from one person to another, so we do not provide cables/wires)
- General purpose extension cord (cut the female end off) to provide power to power supply
- USB cable to power breakout board
- Parallel cable to communicate to breakout board
- Router
- (optional - instead of router) Spindle with power inverter http://www.buildyourcnc.com/SpindlesAndAccessories.aspx
- (if purchasing spindle with inverter) General purpose extension cord (240v) (cut the female end off) to provide power to power inverter
- End Mill(s) http://www.buildyourcnc.com/ProductsEndMills.aspx
- CAD, and/or CAD-CAM software (to produce geometry, machine operations, and g-code) http://www.buildyourcnc.com/CNCsoftware.aspx
- CNC control software (to read g-code and control machine) http://www.buildyourcnc.com/CNCsoftware.aspx

This answer is applicable to most of our machines with the exception of the greenLean and the blueChick since those machines are equipped with a table structure.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
IF I PURCHASE A GREENBULL 6X LONG Z CNC MACHINE KIT AND MACH3, WHAT ELSE WOULD BE REQUIRED TO ASSEMBLE THE WORKING MACHINE? HAVE CAD SOFTWARE.

Mounting the extruder to the whiteAnt can be done a couple of ways. One is to take the 4 mounting holes located at the lower portion of the z-axis rail support and use long screws protruding out. Take a thinner material and drill the four holes matching the locations of the 4 screws and screw on nuts to hold it in place. The other option would be to use the metal bracket and fasten to the edge of the rail support.

Click the link to add information to this solution:
IS IT POSSIBLE TO MOUNT THE NEW EXTRUDER WHITEANT?

What controller are you using to control the cnc machine (Mach3 usb, parallel breakout board, etc.)?

The spindle VFD has an input for 0-10 volts to control the speed and can be used with the MAch3 USB or the Pokeys57CNC board. There are also other terminals in the VFD to control the forwared/reverse and start and stop. Mach3 has parameters to control these output and you need to specify which pins are used for these.

You can also use the TX/RX RS-485 connection on the VFD to have total control using an FTDI USB to serial connector board to connect the computer directly to the VFD.

How to connect the USB to Serial adapter to the VFD:
https://www.buildyourcnc.com/FAQ/13790

FTDI USB to Serial:
https://www.buildyourcnc.com/item/Interfaces-newbiehack-Interfaces-TTL232R-USB-UART-Serial

Pokeys57CNC board:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Mach3 USB board:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Parallel Breakout board:
https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay



Additional Information:
I do apologize for leaving out the parts list.
Leadshine MX4660 4-Axis Digital Stepper Motor Driver
Ethernet SmoothStepper
YL600-2S-2K20 VFD
4 Relay control board
Has anyone had any success getting Mach3 to control the spindle speed and direction?

Click the link to add information to this solution:
I have the 2.2KW VFD. I would like to have it controlled through software. What are the Mode parameters that need to be changed that will allow FWD/ REV, START/STOP and RPM control?

Yes, our porter cable collets and nuts will fit the porter cable 7518.

Additional Information:

Click the link to add information to this solution:
HAVE PORTER CABLE 7518 ROUTER ON MY CNC AND WOULD LIKE TO KNOW IF YOUR ER20 COLLET NUT, FOR THE CABLE, WILL FIT ROUTER.

Yes, it is ok if the thickness is plus or minus +/- about 2mm.

Additional Information:



Additional Information:

Click the link to add information to this solution:
is IT OK TO USE THICKER PLYWOOD (MATERIAL) to BUILD THE CNC MACHINE, BLACKFOOT, BLACKTOE?

Yes, it is ok if the thickness is plus or minus +/- about 2mm.

Additional Information:



Additional Information:

Click the link to add information to this solution:
IT OK TO USE THICKER PLYWOOD (MATERIAL) BUILD THE CNC MACHINE, BLACKFOOT, BLACKTOE?

We do have a relay board that words like a standard relay.

Here is the URL of the relay board that we offer:

https://www.buildyourcnc.com/item/electronicsAndMotors-breakout-Relays-relay-board-250V-12A-5V

Click the link to add information to this solution:
I HAVE YOUR MACH3 USB BOB, DO YOU GUYS SELL A TORCH CONTROL RELAY CAN WIRE UP TO TURN MY PLASMA ON AND OFF HOW WOULD WIFE THAT TOO THIS BOB?

Registration is recommended for a number of reasons. Many choose to register their works because they wish to have the facts of their copyright on the public record and have a certificate of registration. Registered works may be eligible for statutory damages and attorney's fees in successful litigation. Finally, if registration occurs within 5 years of publication, it is considered prima facie evidence in a court of law.

Click the link to add information to this solution:
WHY SHOULD I REGISTER MY WORK IF COPYRIGHT PROTECTION AUTOMATIC?

The blackTooth Laser cutter and Engraver can be built in a weekend. Take a look at the build instructions and try to determine if you feel you have sufficient capability to put together the laser system.

Click the link to add information to this solution:
HOW COMPLEX IS YOUR KIT TO ASSEMBLE, AND MOST IMPORTANTLY - HARD IT SETUP CONTROL THE LASER WITH MACH3?

I WOULD CONSIDER USING A BOARD MADE OUT OF CLOTH AND RESIN AND IS USED IN ELECTRICAL AREAS AS AN INSULATOR. IT IS USUALLY A DARK RED/BROWN IN COLOR AND COMES IN DIFFERENT SIZES. IT IS VERY STRONG AND HEAVY. I DO NOT RECALL THE NAME OF IT, BUT POWER COMPANY LINEMEN HAVE ACCESS TO IT AS IT IS USED IN HIGH VOLTAGE AREAS.

Response:
I FOUND A LINK FOR YOU TO SEE WHAT I AM DESCRIBING. HERE IS THE LINK.. www.electricalinsulationmaterial.com

Response:
Currently our machines are made out of MDO (Medium Density Overlay) plywood, and are used in the construction industry for cement forming. They come lightly coated for moisture protection. Some possibilities for protecting the machine could be:
Painting the structural parts with a oil based paint
Coating the structural parts with a protectant sealant (polyurethane)

Please try to avoid getting any coating or paints on the steel components.

Additional Information:



Additional Information:

Click the link to add information to this solution:
I WOULD BE USING THIS MACHINE IN FIJI. MDF DELAMINATES OVER TIME HERE. HOW PROTECT THE FROM DELAMINATION?

The blackTooth Laser cutter and Engraver can be built in a weekend. Take a look at the build instructions and try to determine if you feel you have sufficient capability to put together the laser system.

Click the link to add information to this solution:
HOW DIFFICULT IS IT TO BUILD THE BLACKTOOTH LASER CUTTER?

Prior to the 2010-11 vaccination season, only children ages 6 months through 18 years and adults age 50 years and older were universally recommended for vaccination; recommendations for adults ages 19 through 49 years were targeted to people with specific risk factors, although other adults could be vaccinated if they wanted protection. Collectively, these targeted risk groups made up 85% of the U.S. population. During the 2009 H1N1 outbreak, additional risk groups were identified, such as obese individuals. The recommendation made by ACIP in February 2010 for universal vaccination simplifies previous recommendations, making it easier for healthcare providers to determine whom to vaccinate. The universal recommendation also makes it easier for patients to remember to get vaccinated every year.

Click the link to add information to this solution:
WE'RE GLAD THAT CDC HAS MADE A UNIVERSAL INFLUENZA VACCINATION RECOMMENDATION TO VACCINATE EVERYONE 6 MONTHS AND OLDER. WOULD YOU TELL US HOW THIS CAME ABOUT?

If you are looking for the drivers to pair with NEMA 34 stepper motors, you can find the 6.0 amp drivers here:
https://www.buildyourcnc.com/item/electronicsAndMotors-stepper-driver-6!0a

The other electronics to send the signals to the 6.0 amp drivers (the control board that operates with the control software) is subject to personal preference, but here they are listed:

Our breakout board (works with Mach3 and LinuxCNC and requires a parallel port on your computer):
https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay

The PoKeys57CNC (works with Mach3 and Mach4):
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Generic USB breakout board (works with Mach3):
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Additional Information:
Do I need a driver for every motor or can I use one driver for all four motors

Additional Information:
Each motor needs its own driver.

Click the link to add information to this solution:
I HAVE NEMA 34 MOTORS BUT NEED THE ELECTRICAL COMPONENTS DO YOU A KIT WITHOUT INCLUDED?

You can determine if the country is serviceable by:
- selecting the items you want to purchase on the website
- go to the cart (shopping cart top left of any webpage)
- log in, or register
- Enter the address and click on calculate shipping.

The webpage will return the direct rates and whether your area is serviced or not. Feel free to enter any address as long as you are able to receive the package from that address.

The shipping times are determined by the service you select in the shopping cart. If a machine is purchased, we generally have a one week lead time unless otherwise stated in the description of the machine's product page.

Additional Information:

Click the link to add information to this solution:
WHAT WOULD BE THE COST OF FREIGHT TO SOUTH AUSTRALIA?

The machines have minimal to no backlash depending on how you apply the machine. Since the cnc machines use roller chain on the x and y axes, and the roller chain is tensioned, the backlash is nearly eliminated. I say nearly because the if you control the machine in a way that there will be excessive load on the end mill, then the machine could have a tendency to spring to one side or the other because of the length of tensioned roller chain. The movement is minor and can be eliminated with the proper control of the machine.

Click the link to add information to this solution:
I'M CURIOUS IF THESE SYSTEMS WILL ENGRAVE LETTERING ACCURATELY WITHOUT BACKLASH?