There are several CAD/CAM programs out there for MacOS. Here is a list of a few: http://www.macuser.de/forum/f53/3d-2d-cad-395058/#post4499316
I've also read good things about punchCAD: http://www.punchcad.com/
Of course, there is always SketchUp if you are in a pinch. There are a few CAM plugins for SketchUp as well, but I've never used them, so I can't vouch for them.

CAD/CAM will get you as far as designing your parts and producing the g-code, but if you also want to run the CNC machine with your Mac, you will need a piece of software similar to Mach3 or EMC to run the g-code. I haven't been able to find anything like these programs that runs on Mac, so you may have to run Mach3 or EMC in Windows using Boot Camp or a virtual machine such as VMware or Parallels.

Personally, I would use the Mac to do all the CAD/CAM, then use a cheap PC to run the CNC machine.

Additional Information:


Additional Information:
EasyDNC for OSX
www.dnc-x.com

Additional Information:


Additional Information:
Hi guys I’m new to the cnc and I’m beginning to learn how to operate and cad-cam software also my cnc runs on Mach3 my questions is if I should use MacBook to do all designs if I can have all this software to run on Mac or I have to use windows software to operate it? I have separate small computer connected to the cnc table who have Mach3 on it please help. Also if you know any other software much easy for beginners please let me know thank you guys!
My email if needed is r1jastrzebski@gmail.com

Additional Information:


Additional Information:
Hi , thank you for your advise!

Additional Information:
Hi , thank you for your advise!

Additional Information:
Hi , thank you for your advise!

Additional Information:
Hi , thank you for your advise!

Additional Information:

Click the link to add information to this solution:
CAN I USE AN APPLE COMPUTER TO RUN THE CNC?

Yes, all of the spindles come with collets. The collets have a 1/4" (6.35mm) bore for end mills that have a 1/4" shank. The ER specification is different for the 1.5kW (ER-11) and the 2.2kW (ER-20).

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
I’M LOOKING TO PURCHASE SPINDLE AND VFD WAS CURIOS IF THE SPINDLES COME WITH COLLETS SO WHICH ONES?

There are several CAD/CAM programs out there for MacOS. Here is a list of a few: http://www.macuser.de/forum/f53/3d-2d-cad-395058/#post4499316
I've also read good things about punchCAD: http://www.punchcad.com/
Of course, there is always SketchUp if you are in a pinch. There are a few CAM plugins for SketchUp as well, but I've never used them, so I can't vouch for them.

CAD/CAM will get you as far as designing your parts and producing the g-code, but if you also want to run the CNC machine with your Mac, you will need a piece of software similar to Mach3 or EMC to run the g-code. I haven't been able to find anything like these programs that runs on Mac, so you may have to run Mach3 or EMC in Windows using Boot Camp or a virtual machine such as VMware or Parallels.

Personally, I would use the Mac to do all the CAD/CAM, then use a cheap PC to run the CNC machine.

Additional Information:


Additional Information:
EasyDNC for OSX
www.dnc-x.com

Additional Information:


Additional Information:
Hi guys I’m new to the cnc and I’m beginning to learn how to operate and cad-cam software also my cnc runs on Mach3 my questions is if I should use MacBook to do all designs if I can have all this software to run on Mac or I have to use windows software to operate it? I have separate small computer connected to the cnc table who have Mach3 on it please help. Also if you know any other software much easy for beginners please let me know thank you guys!
My email if needed is r1jastrzebski@gmail.com

Additional Information:


Additional Information:
Hi , thank you for your advise!

Additional Information:
Hi , thank you for your advise!

Additional Information:
Hi , thank you for your advise!

Additional Information:
Hi , thank you for your advise!

Additional Information:

Click the link to add information to this solution:
CAN I USE A MAC TO CONTROL THE CNC?

If you select the Settings Page and select or tick Auto Limit Override - this will allow you to back off the switch.

Additional Information:
limit and home switch

Click the link to add information to this solution:
IS THERE A WAY TO GET RID OF THE PARALLEL CABLE AND SOMEHOW USE USB ?

Yes, the blueChick kits are available. You can get the shipping rates automatically in the shopping cart. There will be a calculate shipping button on the enter shipping information section of the shopping cart.

Click the link to add information to this solution:
CAN YOU PLEASE TELL ME THE AVAILABILITY OF 12X36 BLUE CHICK 4.2, AND COST FOR SHIPPING TO ZIP 72802 IN RUSSELLVILLE, ARKANSAS?

Temperature probe monitor. Very valuable. This keeps you up to date on your coolant temperature levels.

Voltage meter. This will tell you the exact level of voltage/power you are running telling the laser to run at instead of an arbitrary mark on a drawn wheel around your POT.

Ammeter sensitive to 1mA. This will be sure your not over driving your tube and reducing it's life significantly.

Hour meter. This will tell you exactly how long your system has been 'on' giving you a more accurate bead on the length of your tubes life.

Exhaust fan upgrade. The current fan included is 100CFM. You can buy 120mm fans that push 250CFM and I have included a guide on how to go about doing this here. http://buildyourtools.com/phpBB3/viewto ... 8cdd1802bf

To push the exhaust fan even further, if you have the room/power, I would highly recommend investing in a 600+ CFM "Dust Collector" system. 250CFM is still not suffice to draw all the smoke that can come off of 3mm or 1/8 MDF cutting job.

A cutting surface. I bought myself a aluminum 'egg crate' mesh from my local HVAC company. They are used a cover for fluorescent lights and work great for low impact cutting surface. They come in 4'x8' sheets and are easily cut to fit. The other side is if you can find a steel honeycomb cutting bed to fit. These can be quite costly or fairly affordable depending where you are looking. The benefit of a steel honeycomb is you can use high power magnets to hold material down.

Click the link to add information to this solution:
HOW CAN YOU ENHANCE THE BLACKTOOTH LASER CUTTER?

Check step 9 on this page: http://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay

Click the link to add information to this solution:
IF YOU HAVE CIRCUIT (OR PICTURE) OF HOW THIS RELAY IS CONNECTED TO THE ROUTER

Cooling is not as tricky as you might think. There is 3 ways to approach this, only 2 really matter for a low scale 40w setup. First one is the cheapest and easiest. The higher the temp of water the worse your performance will be, from what I understand anything in the 30C range is about the most tolerable it gets. Lower is better. But not frozen...from what I've been told a very experienced cutter, he found 8C was the highest power he achieved.

1. Use a 5 Gallon resovoir system which gives you a fairly large space of water to heat up before you need to tend to it. Add about a cup of anti-freeze to the mix of DISTILLED water. You don't want ANY minerals in the water that might build up in your system. The anti-freeze works to keep algae and other ickies from growing in your water.

2. Use a smaller resovoir system (or even closed loop) and install 1 or more radiators found in CPU cooling systems with 120mm fans attached. This will continously cool your water system to ambient room temperatures, but with a tiny resovoir it will be difficult to add things like ice-packs to drop the temps if the ambient is quite hot.

3. Using an industrial coolant system. Overkill and unless your cutting A LOT, this is a very expensive option to take. You can also explore the idea of Peltier cooling but it is extremely expensive electricity/BTU wise compared to an industrial cooler.

Click the link to add information to this solution:
HOW CAN COOL THE LASER TUBE?

Cooling is not as tricky as you might think. There is 3 ways to approach this, only 2 really matter for a low scale 40w setup. First one is the cheapest and easiest. The higher the temp of water the worse your performance will be, from what I understand anything in the 30C range is about the most tolerable it gets. Lower is better. But not frozen...from what I've been told a very experienced cutter, he found 8C was the highest power he achieved.

1. Use a 5 Gallon resovoir system which gives you a fairly large space of water to heat up before you need to tend to it. Add about a cup of anti-freeze to the mix of DISTILLED water. You don't want ANY minerals in the water that might build up in your system. The anti-freeze works to keep algae and other ickies from growing in your water.

2. Use a smaller resovoir system (or even closed loop) and install 1 or more radiators found in CPU cooling systems with 120mm fans attached. This will continously cool your water system to ambient room temperatures, but with a tiny resovoir it will be difficult to add things like ice-packs to drop the temps if the ambient is quite hot.

3. Using an industrial coolant system. Overkill and unless your cutting A LOT, this is a very expensive option to take. You can also explore the idea of Peltier cooling but it is extremely expensive electricity/BTU wise compared to an industrial cooler.

Click the link to add information to this solution:
HOW TO COOL THE BLACKTOOTH 40W LASER TUBE

The hub length of the drive sprocket and the other mechanical devise that is used to connect on the shaft will determine the length of the shaft needed for use with the drive sprocket.

The hub lengths for our drive sprockets are 1/2". So if you are connecting the drive sprocket to a motor, your motor shaft will need to be at least 1/2" in length.

Click the link to add information to this solution:
wHAT IS THE SMALLEST LENGTH SHAFT I CAN USE FOR YOUR #25 DRIVE SPROCET?

Yes, the customer will need to sign our NDA (Non Disclosure Agreement) form and send it back to us. We will then send the dxf of the specific updated part of the machine.

Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:
UoZD5KPp

Additional Information:
-1 OR 2+416-416-1=0+0+0+1 --

Additional Information:
-1 OR 2+291-291-1=0+0+0+1

Additional Information:
-1' OR 2+657-657-1=0+0+0+1 --

Additional Information:
-1' OR 2+849-849-1=0+0+0+1 or 'WBwHf8k5'='

Additional Information:
-1" OR 2+276-276-1=0+0+0+1 --

Additional Information:
1'"

Additional Information:
1����%2527%2522

Additional Information:
@@z69Jq

Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
CAN I GET DXF FILES FOR THE UPDATED PARTS OF MY MACHINE?

A standard 40W CO2 laser will cut up to 1/4" thick of material, be it wood, acrylic, card stock, leather, fabric, foam, cork, etc. (Decent speed and final cut are heavily dependent on a strong air assist upgrade)

Metals cannot be cut due to the power level and wavelength of the CO2 laser. But it can be marked with special solutions like Cermark or Thermark.

Click the link to add information to this solution:
WHAT THICKNESS OF MATERIAL CAN THE BLACKTOOTH LASER CUT?

You can determine if the area is serviceable by:
- selecting the items you want to purchase on the website
- go to the cart (shopping cart top left of any webpage)
- log in, or register
- Enter the address and click on calculate shipping.

The webpage will return the direct rates and whether your area is serviced or not. Feel free to enter any address as long as you are able to receive the package from that address.

Click the link to add information to this solution:
WAS WONDERING IF YOU COULD TELL ME WHETHER OR NOT SHIP ANY OF YOUR KIT PRODUCTS TO THE UK?

Well, I've never tried particle board. I would stay away from MDF since it is pretty terrible to breathe. You can use standard ply.

Click the link to add information to this solution:
CAN JUST USE PARTICLE BOAD FOR THE SPOIL BOARD OR SHOULD MDX SOMETHING ELSE?

The roller chain lengths for the greenBull 4x is:
- 13 feet for each side of the X axis (total of 26 feet), and
- 6 feet for the Y-axis

Click the link to add information to this solution:
WHAT LENGTHS OF ROLLER CHAIN DO I USE FOR THE GREENBULL 4X CNC?

U - Pin1
V - Pin2
W - Pin3
Pin4 Dead

Additional Information:
My home made cnc is a big problem with my NC connection. When in start my spindle it will be gone wrong. It will be limith switch problem anytime. Need help thanks.

Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
HOW DO YOU HOOK UP THE SPINDLE TO INVERTER?

Upgrade your mirrors to SI coated mirrors, using a HQ ZnSe lens and even pushing up to a beam expander will all boost power. The ideal order of experimenation for lowest cost would be changing out for a higher quality lens labeled HQ ZnSE lens. Next would be SI mirrors, which will absorb less heat and reflect better, the last would be to use a beam expander which expands the beam, reducing the heat signature on the mirrors and makes a tighter focal width.

Click the link to add information to this solution:
CAN BOOST THE POWER OF MY BLACKTOOTH LASER?

An end mill smaller than 1.5mm or 1/6" is too small a diameter for end mills to cut through materials that are thick. A good rule of thumb is if the end mill has a cutting length that is more than what you want to cut, that diameter will be acceptable.

Click the link to add information to this solution:
CAN .7MM END MILL BE USE TO CUT 15MM MDF?

That shouldn't be a problem. I will need the current rating for the motors. We can subtract the price of the motors. and you can add you own. If you want us to solder the cable to the round connectors and them motor, you would need to send the motors to us.

Let me know and I can send a paypal invoice for the redLeaf without motors.

Click the link to add information to this solution:
DON'T WANT TO USE MY OWN MOTORS FOR THE REDLEAF CNC COMPUTER SYSTEM.