[ Log In ]
[ Register ]
NEW: CNC Router PLANS Available for all of our Newest CNC Models!! Click here to "Design Your CNC".

Question #: 6907

Question: Is a cahin driven y axis that is six feet feesable? What is the best setup other than ballscrew?

Current Solution

The main reason why we chose a chain driven CNC machine is to keep cost down, and works perfectly! It is also pretty simple to setup, so in your application it is feesable!
We currently have our largest CNC machine (greeBull 6X) which runs roller chain for both the X-axis(12Ft.) and Y-axis(6Ft.).

In longer lengths the Lead Screw, and Ball Screw will be hard to get in those lengths without any bends or having it perfectly straight at a low cost, and maybe be harder to accomplish.
Most larger CNC machines, will have to use rack and pinion for the larger lengths, which will have a more complex assembly.
Both the ball screw and rack and pinion will both run (mostly) on aluminum machines.

Respond:

Other Possible Solutions to this Question

  • New here, what is the best 3 axis kit for a Sherline 5400? Higher torque and quietness is my goal. Thanks

    The required motors are the 425 oz-in stepping motors, would be the required motors to run the machine efficiently.

    Click the link to respond:
    New here, what is the best 3 axis kit for a Sherline 5400? Higher torque and quietness is my goal. Thanks

  • I would like some longer HIWIN rails and ballscrews for my x-axis, 9 feet or 108 inches. You list maximums as 78 inches.

    Yes, however, if you are needing a length of the HIWIN specification rail longer than our 78" max length, then you can abut more than one rail together to increase the length of the rail. We do this for our long X-Axis travels on our Fabricator pro machine.

    Click the link to respond:
    I would like some longer HIWIN rails and ballscrews for my x-axis, 9 feet or 108 inches. You list maximums as 78 inches.

  • Would the 425 Oz motor to be strong enough to turn a 4ft 2005 Ballscrew attached to a Gantry that is about 20-30lb?

    Yes, these 425 oz-in motors are very strong. 20-30 lbs is actually very light for these motors, especially when used with ballscrews as the friction coefficient is very low.

    If you ask the customer service live a question like: "how much weight can my motor lift", you will find the formulas to determine the amount of weight the motors at a particular oz-in rating can move. Typical friction coefficients are included in those formulas.

    Click the link to respond:
    Would the 425 Oz motor to be strong enough to turn a 4ft 2005 Ballscrew attached to a Gantry that is about 20-30lb?

  • The slaved axis moves slower that the other motor on the same axis

    If you have a slaved motor, you need to make sure that the two driver's dip switches are set the same so they both use the same microstepping.  You also want to make sure that one of them is not losing steps by setting the motor tuning in such a way that the motor torque has a sufficient buffer.

    Click the link to respond:
    The slaved axis moves slower that the other motor on the same axis

  • Hi Patrick What is the name of that organization for CNC enthusiast in Houston and Katy TX and phone number please. Thanks

    The CNC group is a splinter group of the Woodworker's Club of Houston" and can be found at this website: http://wwch.org

    You can contact them via their contact us page here: http://wwch.org/ClubBus/ContactUs.htm

    They have regular meetings at the location specified on their homepage. You can also go there and talk to some of the CNC group's members.

    Click the link to respond:
    Hi Patrick What is the name of that organization for CNC enthusiast in Houston and Katy TX and phone number please. Thanks

  • hi, what about, if I buy from you some elecronic parts like (3 Axis Electronics Combo) and I use them here in france , where the electric voltage is 220V 50Hertz ? thats gonna works? thanks

    Our electronics contains a switchable power supply that allows you to switch the input mains voltage between 115 volts (110/120) and 230 volts (220/240). the hertx range is not specified, but there are capacitors to smooth out standard frequencies to enable DC output.

    Click the link to respond:
    hi, what about, if I buy from you some elecronic parts like (3 Axis Electronics Combo) and I use them here in france , where the electric voltage is 220V 50Hertz ? thats gonna works? thanks

  • I need a Rigit Coupling that is 1/2" on one side and 5/16 on the other side.Can you get that for me?

    We sell both coupling hubs that can be created to your specific needs. Which will be here https://www.buildyourcnc.com/couplings.aspx and would be the bottom coupling hub's, not the rigid couplings.

    So essentially you would get the Single 1/2" Coupling Hub and the Single 1/4" Coupling Hub, and etc. for different combinations.

    Click the link to respond:
    I need a Rigit Coupling that is 1/2" on one side and 5/16 on the other side.Can you get that for me?

  • I AM USING A XYLOTEX 3 AXIS BOARD AND WANT TO ADD ANOTHER MOTOR SLAVED THE X-AXIS. WILL DRIVE CW230 WORK?

    If the pins from the terminal block on the side of the board are outputs, or at least 2 of them are outputs, then you can connect our modular driver to the board (example: cw230). If they are all inputs, then you would not be able to connect an external driver.

    Click the link to respond:
    I AM USING A XYLOTEX 3 AXIS BOARD AND WANT TO ADD ANOTHER MOTOR SLAVED THE X-AXIS. WILL DRIVE CW230 WORK?

  • Must I have licence to run planetpc software, is there any other software that will run the usb controller

    The Planet CNC Software will require purchase after the trial version is completed, and will be purchased through their website. Currently that is the only software available for the USB Controller.

    Click the link to respond:
    Must I have licence to run planetpc software, is there any other software that will run the usb controller

  • What causes one of my two x-axis motors to stop while the Mach 3 program is still running?

    If one of your stepper motors decides to stop moving and the others are moving during a CNC milling or laser cutting job, then there could be two things that could be causing this.

    - The motor found its limiting torque (usually comes with a not-so-pleasant sound). This is where the control software is trying to move the stepper motor too fast (velocity, or too fast too quickly, acceleration) and the load against the stepper motor (inertia of the machine, or the material against the end mill while milling). Recommended action is to lower the velocity and/or acceleration, and/or lower the feedrate when cutting.

    - There is a wiring issue with the wiring from the driver to the motor. This could be a loose wire, or a chafed wire (or two shorting together). It can also be a loose digital wire from the controller board to the driver. Sometimes wire ties can be the culprit. Recommended action would be to thoroughly inspect the wiring.

    It's probably not the limit switches since that would cause a stop to the entire motion of the cnc router or laser machine.

    Sometimes Mach3 will show a status when something goes wrong, but in cases where the motor is stopping due to its torque limit, then that would not be shown in the status. It's always good to check it anyway.

    Additional Information:
    I need to clarify my situation a little better after going to my shop and trying to run another program on Mach 3. About 15 minutes into the milling process all the motors (2-X axis, Y axis and Z axis)stop but the program continues to run. I stop the program and after a couple of minutes when I try to restart the program all the motors start working again. Then after another 15 minutes or so, all the motors stop again. I checked and rechecked my wiring. This has never happened to me before when running the same programs with the same setups and motor speeds. All of a sudden when I reloaded a program I successfully used before it does this. Do you have any recommendations?

    Additional Information:
    Yeah, it sounds like a more complex issue. Have you tried running in the air without using the spindle. This may be a power related issue.

    Additional Information:
    That's exactly what I did. I ran the program without the router motor on just to see if the motors would get through the whole program but they stopped working after about fifteen minutes and then I was able to start them again after about 3 or 4 minutes. I never had this problem before so you can imagine my frustration especially after ruining a couple of projects on expensive material.

    Additional Information:
    Sure. I can completely understand. Try this: disconnect all but one of the driver from power and digital connection and do the air run. Repeat this for each driver and note your findings. This will rule out the drivers causing a power failure.

    Also, is your stepper motors and drivers on a separate power circuit from the computer?

    Additional Information:
    I will try disconnecting each driver and digital connection, which will be a real pain because it will be hard to access.

    All the stepper motors, drivers and computer are plugged into the same power strip.

    Additional Information:
    Ok, so there is no power failure going on, but I believe it is necessary to test each stepper motor and driver pair individually. Hopefully that will lead to a conclusion.

    Additional Information:
    It will take a little time but I will do it and report back on my findings.

    Additional Information:
    Curious, what machine is exhibiting this problem?

    Additional Information:
    I purchased a BYCNC kit back in 2009 with an approximate cutting area of 2' X 4'. I later changed out the Z-Axis Motor and controller for a larger one and have two X-axis motors and controllers. In 2010 I rebuilt the machine out of birch plywood instead of the particle board that the kit supplied. I sent Patrick pictures to him. The machine never gave me a problem till now.

    Additional Information:
    Thanks for the update. This is Patrick by the way. I answer pretty much all of the Customer Service questions. That machine has given quite a good history.

    Additional Information:
    I love the machine and made a number of samples of my work for my e-commerce site, but I can't start selling product until I know this problem is solved because I will not be able to fulfill orders. I finally got all the electronics out of its enclosed protected area near the machine so that I test each controller as you recommended. I hope the problem can be rectified. Will let you know.

    Additional Information:
    Thanks.

    Additional Information:
    I tested each stepper motor and driver pair individually and they worked so what might be the next step?

    Additional Information:
    Did each stepper motor driver pair work for the full +15 minutes?

    Additional Information:
    Yes, I had them in operation for over 30 minutes.

    Additional Information:
    Ok, well it’s good that the motors and driver are ok. We are now down to the power supply and the breakout board as possible causes for the stop. I have a feeling it may be the power supply where with all three drivers drawing current and the power supply maybe getting too hot. Is the fan in the power supply working? You can also test to see if there is 36 volts on the power supply voltage output (V+ and V-).

    Regarding the breakout board, if you have an oscilloscope, you can test if the driver pulses are outputting, but I would consider this as a last resort after you determine if there is a problem with the power supply.

    Additional Information:
    I tested the power supply with a voltmeter and each output was registering 39-40 volts. I think the problem may be the g-code. I am using V-Carve pro to do design and output to Mach 3 Mill g-code. When I studied the g-code lines I noticed that further into the program the z-axis g-code stopped zeroing out to move to the next part of the carving. In other words both the x and y keep moving and the z just stopped working because there was g-code missing. I think something is missing when the design was converted to g-code. I noticed that when I ran a simpler project it worked without problems so I need to investigate this further.

    Additional Information:
    New Update, Its not the g-code. I started to run the long program and everything was working fine until about 45 minutes into it, all the motors stopped working (but the program was still running) and there was a high pitched hum. When I put my hands on the motors they were all trying to move but it seemed they were all stalled. I turned the power off, gave it a minute and when I turned it back on I was able to move the motors again. Could this be a power supply problem?

    Additional Information:
    It does sound more and more like a power supply problem. Did you test the power supply after the motors stopped?

    Additional Information:
    No, I did not. What should I be looking for.

    Additional Information:
    It’s good that you know the voltage during normal operation, so you have a base understood. If the power supply is the problem, the voltage will be reduced or non existent when measured after the problem.

    Additional Information:
    Also, check to see if the fan is running on the power supply when the motors stop. That may (not absolutely) be an indication.

    Additional Information:
    I'll run another test, check the voltage and fan when the problem occurs and let you know. Thanks for hanging in there with me as we try to resolve the problem.

    Additional Information:
    It’s my pleasure. This service is rarely used and is faster then email. Odd nobody uses it. Any recommendations you can give would be great. No problem using this FAQ to pose ideas as this resolution will be cleaned up later.

    Additional Information:
    It might be that people do not realize you can communicate through the sight like this because they are so used to e-mail and texting. You may want to explain this feature in the customer service section.

    I ran the program this morning and it did not take long before the motors stopped. While operating the voltages for all three motors was 46 volts, when the motors stalled (and again there was a high pitch hum) the voltage went up to 60 volts and the fan on the power supply was operating.

    Additional Information:
    So, the driver work individually, but not all together. There is a high pitch sound when the motors fail. You have noted 60 volts from the power supply and the supply fan remains on. This is a difficult issue to resolve, but it seems to me that your power supply may be bad. The 60v measurement tells me that the current dropped and ohms law tells us that is current drops, volts will rise if the resistance stays the same.

    Additional Information:
    As one last test I am going to test each driver again and let them go through the entire program because it seems that the failure can occur at the beginning or towards the end of the program. When I originally tested ach driver I let them run for about a half an hour and the program takes over an hour to run completely. I just want to make sure that it is not the drivers. I will report back when I finished but as you noted it may be the power supply but I want to make sure.

    Additional Information:
    That’s a great idea.

    Additional Information:
    I just ran the x-axis through the whole program and there was no problem especially since I have two NEMA 23 motors moving that axis. Before I check the Y and Z could having a NEMA 34 on the Z axis with appropriate controller be a problem. I used the larger motor on the z axis because the router I am using is a large 1 1/2 hp. I've run this program in the past with this set-up and have not had a problem.

    Additional Information:
    Having a, say 3.0 amp driver, driving a stepper motor that typically requires a 6 amp driver would not seem to be an issue since the driver is limiting the current draw, but the driver may not be able to handle larger coil and back EMF with the protection on the 3.0 amp driver. With that said, I don’t believe that is the issue in this case.

    Additional Information:
    I don't either because I was able to run this and other complicated programs with this set-up in the past. I will let you know on the y and z axis.

    Additional Information:
    Thanks

    Additional Information:
    I ran the Y axis and z axis separately through the entire program and there was no stopping or problem. I guess the culprit is the power supply and I'll order a new one and hope that resolves the problem.

    Additional Information:
    Yes, that is the most probable cause. Please keep me informed. Thanks!

    Additional Information:
    Received and installed the new power supply. I ran the program with the router on and it worked flawlessly. The program runs for an hour and a half and I did not have a single problem. I guess it was the power supply but I was glad to go through all the diagnostics we discussed before replacing it. I hope this power supply lasts a lot longer than the last one. Thanks much for hanging in there with me and coming up with the solution.

    Additional Information:
    It’s my absolute pleasure and I am so happy to hear that the power supply replacement solved the problem.

    Additional Information:


    Additional Information:
    Y axis stop working X & Z work fine Y axis has two motors have check wiring & connections new breakout board still the same port & Pin set OK dont no were to go next David

    Additional Information:

    Click the link to respond:
    What causes one of my two x-axis motors to stop while the Mach 3 program is still running?

  • WHAT ARE THE BEST FOODS THAT WILL HELP YOU LOSE WEIGHT?

    Lettuce, or any vegetable. Also drink a cup of water before meals, it'll make you feel fuller.

    Click the link to respond:
    WHAT ARE THE BEST FOODS THAT WILL HELP YOU LOSE WEIGHT?

  • Going to purchase a new laptop computer. Question. What is the minimal requirement for laptops running cnc planet software and other softwares that are needed?

    Your purchase of a laptop will depend on what CNC software and CNC interface you will be using. In most cases, CNC interfaces use a parallel port, or the interface will convert USB instructions into a form of parallel I/O pins. We provide both types of interfaces, but you will be required to use specific software packages compatible with the interface. The USB interface that we sell at the moment is only compatible with Planet-CNC software (which is very good software), and if the computer has a parallel port, you will have your choice of many software titles including (but not limited to) Mach3 and LinuxCNC.

    The hardware and processing performance is not as important. Computers with relatively slow processors (i.e. Pentium) can control a CNC machine and achieve good performance.

    If you intend using CAD and CAM on that computer, then you will want a more modern computer that will have a good amount of memory and processing power. You will need to refer to the software requirements for the minimum specifications.

    Click the link to respond:
    Going to purchase a new laptop computer. Question. What is the minimal requirement for laptops running cnc planet software and other softwares that are needed?

  • Is there any other software that will work with your controller Mach3?

    The mach3 control software will work with all major CAM software (CAMBAM, Aspire and Vectric, BobCAD/CAM, ArtCAM, Dolphin CAM, CAM software that integrate with SolidWorks and AutoDesk Inventor, and many more).

    Click the link to respond:
    Is there any other software that will work with your controller Mach3?

  • WHAT CAUSES ONE OF MY TWO AXIS MOTORS TO STOP WHILE THE MACH3 PROGRAM IS STILL RUNNING

    If one of your stepper motors decides to stop moving and the others are moving during a CNC milling or laser cutting job, then there could be two things that could be causing this.

    - The motor found its limiting torque (usually comes with a not-so-pleasant sound). This is where the control software is trying to move the stepper motor too fast (velocity, or too fast too quickly, acceleration) and the load against the stepper motor (inertia of the machine, or the material against the end mill while milling). Recommended action is to lower the velocity and/or acceleration, and/or lower the feedrate when cutting.

    - There is a wiring issue with the wiring from the driver to the motor. This could be a loose wire, or a chafed wire (or two shorting together). It can also be a loose digital wire from the controller board to the driver. Sometimes wire ties can be the culprit. Recommended action would be to thoroughly inspect the wiring.

    It's probably not the limit switches since that would cause a stop to the entire motion of the cnc router or laser machine.

    Sometimes Mach3 will show a status when something goes wrong, but in cases where the motor is stopping due to its torque limit, then that would not be shown in the status. It's always good to check it anyway.

    Additional Information:
    I need to clarify my situation a little better after going to my shop and trying to run another program on Mach 3. About 15 minutes into the milling process all the motors (2-X axis, Y axis and Z axis)stop but the program continues to run. I stop the program and after a couple of minutes when I try to restart the program all the motors start working again. Then after another 15 minutes or so, all the motors stop again. I checked and rechecked my wiring. This has never happened to me before when running the same programs with the same setups and motor speeds. All of a sudden when I reloaded a program I successfully used before it does this. Do you have any recommendations?

    Additional Information:
    Yeah, it sounds like a more complex issue. Have you tried running in the air without using the spindle. This may be a power related issue.

    Additional Information:
    That's exactly what I did. I ran the program without the router motor on just to see if the motors would get through the whole program but they stopped working after about fifteen minutes and then I was able to start them again after about 3 or 4 minutes. I never had this problem before so you can imagine my frustration especially after ruining a couple of projects on expensive material.

    Additional Information:
    Sure. I can completely understand. Try this: disconnect all but one of the driver from power and digital connection and do the air run. Repeat this for each driver and note your findings. This will rule out the drivers causing a power failure.

    Also, is your stepper motors and drivers on a separate power circuit from the computer?

    Additional Information:
    I will try disconnecting each driver and digital connection, which will be a real pain because it will be hard to access.

    All the stepper motors, drivers and computer are plugged into the same power strip.

    Additional Information:
    Ok, so there is no power failure going on, but I believe it is necessary to test each stepper motor and driver pair individually. Hopefully that will lead to a conclusion.

    Additional Information:
    It will take a little time but I will do it and report back on my findings.

    Additional Information:
    Curious, what machine is exhibiting this problem?

    Additional Information:
    I purchased a BYCNC kit back in 2009 with an approximate cutting area of 2' X 4'. I later changed out the Z-Axis Motor and controller for a larger one and have two X-axis motors and controllers. In 2010 I rebuilt the machine out of birch plywood instead of the particle board that the kit supplied. I sent Patrick pictures to him. The machine never gave me a problem till now.

    Additional Information:
    Thanks for the update. This is Patrick by the way. I answer pretty much all of the Customer Service questions. That machine has given quite a good history.

    Additional Information:
    I love the machine and made a number of samples of my work for my e-commerce site, but I can't start selling product until I know this problem is solved because I will not be able to fulfill orders. I finally got all the electronics out of its enclosed protected area near the machine so that I test each controller as you recommended. I hope the problem can be rectified. Will let you know.

    Additional Information:
    Thanks.

    Additional Information:
    I tested each stepper motor and driver pair individually and they worked so what might be the next step?

    Additional Information:
    Did each stepper motor driver pair work for the full +15 minutes?

    Additional Information:
    Yes, I had them in operation for over 30 minutes.

    Additional Information:
    Ok, well it’s good that the motors and driver are ok. We are now down to the power supply and the breakout board as possible causes for the stop. I have a feeling it may be the power supply where with all three drivers drawing current and the power supply maybe getting too hot. Is the fan in the power supply working? You can also test to see if there is 36 volts on the power supply voltage output (V+ and V-).

    Regarding the breakout board, if you have an oscilloscope, you can test if the driver pulses are outputting, but I would consider this as a last resort after you determine if there is a problem with the power supply.

    Additional Information:
    I tested the power supply with a voltmeter and each output was registering 39-40 volts. I think the problem may be the g-code. I am using V-Carve pro to do design and output to Mach 3 Mill g-code. When I studied the g-code lines I noticed that further into the program the z-axis g-code stopped zeroing out to move to the next part of the carving. In other words both the x and y keep moving and the z just stopped working because there was g-code missing. I think something is missing when the design was converted to g-code. I noticed that when I ran a simpler project it worked without problems so I need to investigate this further.

    Additional Information:
    New Update, Its not the g-code. I started to run the long program and everything was working fine until about 45 minutes into it, all the motors stopped working (but the program was still running) and there was a high pitched hum. When I put my hands on the motors they were all trying to move but it seemed they were all stalled. I turned the power off, gave it a minute and when I turned it back on I was able to move the motors again. Could this be a power supply problem?

    Additional Information:
    It does sound more and more like a power supply problem. Did you test the power supply after the motors stopped?

    Additional Information:
    No, I did not. What should I be looking for.

    Additional Information:
    It’s good that you know the voltage during normal operation, so you have a base understood. If the power supply is the problem, the voltage will be reduced or non existent when measured after the problem.

    Additional Information:
    Also, check to see if the fan is running on the power supply when the motors stop. That may (not absolutely) be an indication.

    Additional Information:
    I'll run another test, check the voltage and fan when the problem occurs and let you know. Thanks for hanging in there with me as we try to resolve the problem.

    Additional Information:
    It’s my pleasure. This service is rarely used and is faster then email. Odd nobody uses it. Any recommendations you can give would be great. No problem using this FAQ to pose ideas as this resolution will be cleaned up later.

    Additional Information:
    It might be that people do not realize you can communicate through the sight like this because they are so used to e-mail and texting. You may want to explain this feature in the customer service section.

    I ran the program this morning and it did not take long before the motors stopped. While operating the voltages for all three motors was 46 volts, when the motors stalled (and again there was a high pitch hum) the voltage went up to 60 volts and the fan on the power supply was operating.

    Additional Information:
    So, the driver work individually, but not all together. There is a high pitch sound when the motors fail. You have noted 60 volts from the power supply and the supply fan remains on. This is a difficult issue to resolve, but it seems to me that your power supply may be bad. The 60v measurement tells me that the current dropped and ohms law tells us that is current drops, volts will rise if the resistance stays the same.

    Additional Information:
    As one last test I am going to test each driver again and let them go through the entire program because it seems that the failure can occur at the beginning or towards the end of the program. When I originally tested ach driver I let them run for about a half an hour and the program takes over an hour to run completely. I just want to make sure that it is not the drivers. I will report back when I finished but as you noted it may be the power supply but I want to make sure.

    Additional Information:
    That’s a great idea.

    Additional Information:
    I just ran the x-axis through the whole program and there was no problem especially since I have two NEMA 23 motors moving that axis. Before I check the Y and Z could having a NEMA 34 on the Z axis with appropriate controller be a problem. I used the larger motor on the z axis because the router I am using is a large 1 1/2 hp. I've run this program in the past with this set-up and have not had a problem.

    Additional Information:
    Having a, say 3.0 amp driver, driving a stepper motor that typically requires a 6 amp driver would not seem to be an issue since the driver is limiting the current draw, but the driver may not be able to handle larger coil and back EMF with the protection on the 3.0 amp driver. With that said, I don’t believe that is the issue in this case.

    Additional Information:
    I don't either because I was able to run this and other complicated programs with this set-up in the past. I will let you know on the y and z axis.

    Additional Information:
    Thanks

    Additional Information:
    I ran the Y axis and z axis separately through the entire program and there was no stopping or problem. I guess the culprit is the power supply and I'll order a new one and hope that resolves the problem.

    Additional Information:
    Yes, that is the most probable cause. Please keep me informed. Thanks!

    Additional Information:
    Received and installed the new power supply. I ran the program with the router on and it worked flawlessly. The program runs for an hour and a half and I did not have a single problem. I guess it was the power supply but I was glad to go through all the diagnostics we discussed before replacing it. I hope this power supply lasts a lot longer than the last one. Thanks much for hanging in there with me and coming up with the solution.

    Additional Information:
    It’s my absolute pleasure and I am so happy to hear that the power supply replacement solved the problem.

    Additional Information:


    Additional Information:
    Y axis stop working X & Z work fine Y axis has two motors have check wiring & connections new breakout board still the same port & Pin set OK dont no were to go next David

    Additional Information:

    Click the link to respond:
    WHAT CAUSES ONE OF MY TWO AXIS MOTORS TO STOP WHILE THE MACH3 PROGRAM IS STILL RUNNING

  • COULD YOU PLEASE EXPLAIN, IF IT'S TRUE, THAT HANDS-FREE CELL PHONE CAR MICROPHONES RADIATE MORE THAN ANY OTHER INSTRUMENT USED WITH THESE PHONES?

    Hands-free cell phone car microphones have been tested by the manufacturers and meet the current ANSI/IEEE (American National Standards Institute/Institute of Electrical and Electronics Engineers) standards for radiofrequency (RF) safety. These are the same standards that the Federal Communications Commission enforces under the Telecommunications Act of 1996, and they place limits on the specific absorption rate (SAR) of RF energy in the body. Recent inflammatory articles in the British press were not substantiated by testing at ISO-accredited testing facilities at Motorola. Manufacturers of cell phones are required under FCC regulations to assure that their products meet the SAR limits on both hand-held and hands-free units. Further information can be obtained on the Internet at The Center for Devices and Radiological Health (FDA information) or Office of Engineering and Technology (FCC information).

    Click the link to respond:
    COULD YOU PLEASE EXPLAIN, IF IT'S TRUE, THAT HANDS-FREE CELL PHONE CAR MICROPHONES RADIATE MORE THAN ANY OTHER INSTRUMENT USED WITH THESE PHONES?

  • HOW DO I WIRE THE 4TH AXIS THAT YOU SELL. I HAVE MACH3 SOFTWARE. NO INSTRUCTIONS ON YOUR SITE

    The motor that is attached to the 4th axis is wired as follows:

    The motor should have red, green yellow and blue wires coming form the motor. The red and green are paired as one coil and the yellow and blue is paired as the other coil. You can wire the motor to a 3.0 amp driver with red to A+, green to A-, Yellow to B+ and Blue to B-

    Click the link to respond:
    HOW DO I WIRE THE 4TH AXIS THAT YOU SELL. I HAVE MACH3 SOFTWARE. NO INSTRUCTIONS ON YOUR SITE

  • Hello thank you for the wonderful your efforts.may i ask? What is the unit of measurement used?

    The units of measurement that we use is Imperial, (inches, feet, etc.) but Metric units can be used with our machines as well (millimeters, centimeter, etc.).

    Click the link to respond:
    Hello thank you for the wonderful your efforts.may i ask? What is the unit of measurement used?

  • Do the 5 Axis Breakout Board with Relay requires software to setup

    The breakout board does not require software to run, specifically. The breakout board serves only as a signal conditioner where the input signal from the computer is output at the corresponding terminal, or the terminal receives a signal and is conditioned and sent to the parallel connector to be read by the computer. As long as the software can communicate to the parallel port of the computer, then the breakout board will function.

    Click the link to respond:
    Do the 5 Axis Breakout Board with Relay requires software to setup

  • Hey. I have noticed that you guys use roller chain to move x,y axis and a lead screw to move the z axis, can you please explain the motivation in short? Thank you.

    Dealing with running our CNC machines with roller chain on the X/Y-axes and lead screw on the Z-axis, we chose this method due to functionality and cost effectiveness. We wanted to make the lowest cost CNC machine available for our customers without taking to much functionality and precision away from the machine. We wanted the accuracy and cost effectiveness to be surprisingly high, with our machines getting thousandths of an inch will be no issue, and having it at a decent price!

    Click the link to respond:
    Hey. I have noticed that you guys use roller chain to move x,y axis and a lead screw to move the z axis, can you please explain the motivation in short? Thank you.