Most of our power supplies allow for a 9 amp current draw.

For the Neutral, Live and earth ground, wire gauge for that level of current is 14 for relatively short cable lengths. Increase the gauge for longer lengths past 25 feet.

For the DC 24V output terminals to the drivers, 20 gauge is fine. If the power supply is connecting to only one driver, increase the wire gauge to 14.

Additional Information:
What gage wire should I use from motor to driver

Additional Information:


Additional Information:

Click the link to add information to this solution:
WIRE GAUGE FOR POWER SUPPLY

This video will illustrate how to test for laser power:

Click the link to add information to this solution:
LOSE POWER IN MY LASER TUBE

Here is the wiring diagram for the MAch3 USB breakout board:
https://www.buildyourcnc.com/Documents/Electric%20Wiring%20Diagram.pdf

You will need 24 volt relays for the output on that board since that side of the board requires 24 volt power at the V+ and V-

Customer Response:
My inquiry is for the Planet CNC USB and 5v relays.
I am 99% finished with my 2 axis lathe build and this is the last item for me to conquer.
I want to control power to router, and vacuum with the BOB going through the 5V relays purchased on this site.
Thanks again.

Using the Mist, spindle or flood pins...

Buildyourcnc response:
There is an IN, GND and 5V for the digital side to engage the relay. There is an S, O and P for the power line of the device to be controlled.

The 5V and GND must be connected to the 5V and GND from the USB board. The IN is the wire from the output terminal (i.e. mist, flood, spindle).

For the power side, here are the scenarios:
- P to O connection is normally open
- P to S connection is normally closed

So, if you have the power wire that would plug into the wall, the L "black" wire from the power cord will pass through this part of the circuit (cutting the wire and one end in the P terminal and the other end in the O or S terminal). Generally, the P to O is used as this connection is normally open and when the relay is engaged, the circuit will close allowing the current to flow through that wire.

Click the link to add information to this solution:
SIGNAL AND 5V POWER WIRING DIAGRAM FOR RELAY USB BR ABOUT BOARD.

Upgrade your mirrors to SI coated mirrors, using a HQ ZnSe lens and even pushing up to a beam expander will all boost power. The ideal order of experimenation for lowest cost would be changing out for a higher quality lens labeled HQ ZnSE lens. Next would be SI mirrors, which will absorb less heat and reflect better, the last would be to use a beam expander which expands the beam, reducing the heat signature on the mirrors and makes a tighter focal width.

Click the link to add information to this solution:
CAN BOOST THE POWER OF MY BLACKTOOTH LASER?

The spindle inverter (VFD) will run on a 220V (or between 170V-250V) power source with either 50Hz or 60Hz.

Click the link to add information to this solution:
DOES THE SPINDLE RUN ON A 50HZ POWER SOURCE?

check your in-going power and make sure that you have a good neutral connection. Frequently the issue is not the power supply but the power coming into the power supply that causes the problem. There is a chance that the power is good coming in but there is a loose neutral connection and that causes it. This is the neutral connection that runs all the way back to the panel in your home.

Click the link to add information to this solution:
WHY DO MY 40W LASER POWER SUPPLIES KEEP FAILING?

Make sure you follow the tutorial here: http://www.buildyourcnc.com/CNCElectronicsandWiring.aspx

Click the link to add information to this solution:
THE MOTORS ARE NOT TURNING

This video will illustrate how to test for laser power:

Click the link to add information to this solution:
HOW TO KNOW IF THE POWER SUPPLY OF THE LASER TUBE IS DAMAGED

In Mach3, go to the Settings Tab, and select "Set Steps Per Unit". It will ask you how far to move the machine. Before you do this, make a mark on the table exactly where the end mill is resting. You can do this by lowering the end mill until it touches the material, then spinning it by hand to cut a small dimple in the material. Then, raise the end mill to clear the material, and assign a distance to move the machine. Once the machine moves and stops, measure the exact distance that it actually traveled with a tape measure, and enter this value into the dialog box that asks how far it moved. Mach3 will automatically adjust your steps per unit for that axis to be more accurate. Do this for all axes often to ensure you are cutting accurately. The longer distances you use calibrate, and the more precise you are with your measurements, the better.

Click the link to add information to this solution:
MY MACHINE NOT ACCURATE

PC with parallel port and USB port
20awg stranded wires for the motors - http://www.buildyourcnc.com/electronicscombo.aspx
18awg stranded wires for power supply to drivers
24awg stranded wires for breakout board to drivers
(location and spacing of components varies from one person to another, so we do not provide cables/wires)
- General purpose extension cord (cut the female end off) to provide power to power supply
- USB cable to power breakout board
- Parallel cable to communicate to breakout board
- Router
- (optional - instead of router) Spindle with power inverter http://www.buildyourcnc.com/SpindlesAndAccessories.aspx
- (if purchasing spindle with inverter) General purpose extension cord (240v) (cut the female end off) to provide power to power inverter
- End Mill(s) http://www.buildyourcnc.com/ProductsEndMills.aspx
- CAD, and/or CAD-CAM software (to produce geometry, machine operations, and g-code) http://www.buildyourcnc.com/CNCsoftware.aspx
- CNC control software (to read g-code and control machine) http://www.buildyourcnc.com/CNCsoftware.aspx
- If the machine does not have the table included, then a table will need to be built. The rails, chain and chain mounts are included that are used on this table.

Additional Information:

Click the link to add information to this solution:
WHAT NOT INCLUDED WITH THE MACHINE?

Yes, we accept standard credit cards on our shopping cart. All you need to do is enter the credit card information in the payment area.

Click the link to add information to this solution:
DO NOT HAVE PAYPAL ACCOUNT, WITH NO DESIRE TO OBTAIN ONE.

If your computer does not have a parallel port, all you will need is a low cost PCI parallel adapter card (these can be found on amazon for $15-$20). If you plan on using a laptop (not recommended) you can try to find a PCMCIA parallel adapter, but many people have frequent issues with this setup. A more expensive solution would be to purchase a USB smooth stepper board. Unfortunately, we do not supply any of these adapters and cannot attest to their reliability.

Additional Information:
ur gay

Additional Information:

Click the link to add information to this solution:
MY COMPUTER DOES NOT HAVE A PARALLEL PORT. WHAT DO I NEED?