[ Log In ]
[ Register ]
NEW: CNC Router PLANS Available for all of our Newest CNC Models!! Click here to "Design Your CNC".

Question #: 6924

Question: Hi, whats the actual (with the fixed errata) laser electronic wiring diagram for the blacktooth? thank you

Current Solution

Which wiring diagram are you specifically requesting? Due to your current model blackTooth? We currently have two wiring diagrams, Parallel Interface board (https://www.buildyourcnc.com/images/LaserWiringParallel.jpg) and the USB interface board (https://www.buildyourcnc.com/images/LaserWiringUSB.jpg). Also if you have the new model blackTooth with the control unit, we still do not currently have that wiring diagram in a document format!

Respond:

Other Possible Solutions to this Question

  • WHERE ARE THE WIRING DIAGRAMS FOR BLACKTOOTH LASER CUTTER IN INSTRUCTIONS?

    You can find the wiring diagrams for the blackTooth on step 105 and 106 on the list of instructions on the blackTooth page. Step 105 pertains to the parallel breakout board and step 106 pertains to the USB interface board.

    Additional Information:
    wire size

    Click the link to respond:
    WHERE ARE THE WIRING DIAGRAMS FOR BLACKTOOTH LASER CUTTER IN INSTRUCTIONS?

  • Where are the wiring diagrams for the blackTooth laser cutter?

    You can find the wiring diagrams for the blackTooth on step 105 and 106 on the list of instructions on the blackTooth page. Step 105 pertains to the parallel breakout board and step 106 pertains to the USB interface board.

    Additional Information:
    wire size

    Click the link to respond:
    Where are the wiring diagrams for the blackTooth laser cutter?

  • How can i get a complete list of all the components (electronics) I need for a CNC laser cutter with the laser controller? A wiring Diagram would probably be very helpful.

    All the options for and variations of our blackTooth laser cutter/engraver are available on our website here https://buildyourcnc.com/blackToothLaserCutterAndEngraver.aspx#prettyPhoto. The wiring diagram is available here: https://buildyourcnc.com/blackToothLaserCutterAndEngraver.aspx#prettyPhoto/0/
    We do not offer plans or a bill of materials for our machines at this time, but if you are interested in doing your own from scratch you can learn a lot about the design and build process from our tutorials. We wish you success in your endeavors.

    Click the link to respond:
    How can i get a complete list of all the components (electronics) I need for a CNC laser cutter with the laser controller? A wiring Diagram would probably be very helpful.

  • The page "Wiring Instruction for the Electronics Combo" contains links that play advertisements, but have no actual instructional videos.

    I would check for any toolbar's and/or plugins on your web browser if non-stop advertisement videos appear. Now courtesy of a YouTube member that has created a completer playlist of our videos!

    Be aware these videos are a bit outdated and might confuse you with our newer boards!

    (

    &list=PL122021172205E9AA)

    Click the link to respond:
    The page "Wiring Instruction for the Electronics Combo" contains links that play advertisements, but have no actual instructional videos.

  • Is there a complete wiring diagram for the Medium Combo Kit with the usb board? Your USB tutorial does not cover the modular 2.5a drivers. https://buildyourcnc.com/item/electronicsAndMotors-3axis-100-elcombo

    We are currently getting it completed for us to post it under the 2.5A stepper driver page. However here is the correct wiring procedure.

    First: Wire the 24V power supply to the 2.5A driver, by wiring +V on the power supply to 12-24V on the driver. Next wire the COM on the power supply to Ground(GND) on the 2.5A driver. GND on the driver will also go to the GND on the USB board, for specific axis. (additional 3-4 wires connected to ground will be needed for the other axes as well).

    Second: Wire the USB board to the driver(one driver per axis on the USB board):
    CP on the driver will go to CP on the desired axis on the USB board.
    CW on the driver will go to CW on the desired axis on the USB board.
    5V will go to the VCC pin on the keyboard jog pins on the USB board (check schematic here: https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-USB-Controller-Breakout#prettyPhoto/2/).
    GND on the USB board to GND on the driver. (as specified in step 1).
    EN is not used.

    Personal Note:
    I would recommend that you crimp the VCC pin to a wire which could be split for the other axes as well, each driver will need 5V.

    Third: Wire the stepper motor to the driver, (using either the Nema 23 100-oz or the Nema 17 62-oz stepper motors, the wiring will be the same. For the Nema 23 the yellow and white is not connected.)
    Black to A1
    Green to A2
    Red to B1
    Blue to B2

    Fourth: Repeat steps 1-3 for each driver/motor per axis.

    Mention: Remember that GND on the driver will also go to the GND on the USB board for specific axis, and VCC pin on the USB board (keyboard jog) will go to 5V on all drivers for each axes as well, each driver will need 5V!

    Click the link to respond:
    Is there a complete wiring diagram for the Medium Combo Kit with the usb board? Your USB tutorial does not cover the modular 2.5a drivers. https://buildyourcnc.com/item/electronicsAndMotors-3axis-100-elcombo

  • On the blacktooth machine wiring diagram for parallel breakout a wire goes from 6 on the BOB to TL on the laser power supply. My power supply has an"H" followed by a "L". Which is correct? I've connected to the "L" but the laser appears always on.

    The digital signal portion of the CO2 laser tube power supply has various terminals for signal power, signal gnd, laser intensity and engaging the laser (turning it on or off). The TL and TH are triggers to turn the laser power on or off. These may be labeled L or H on some laser power supplies. You can use either TL/L, or TH/H to control the laser.

    If you use the TL or L terminal to control the laser:
    If a low signal (gnd) is present at that terminal, the laser will turn on. If a high signal (5v) is present, the laser will turn off.

    If you use the TH or H terminal to control the laser:
    If a high signal (5v) is present at that terminal, the laser will turn on. If a low signal (gnd) is present, the laser will turn off.

    You should first test the control signal from the interface with a multimeter to make sure the laser will be controlled correctly before powering the laser power supply

    Click the link to respond:
    On the blacktooth machine wiring diagram for parallel breakout a wire goes from 6 on the BOB to TL on the laser power supply. My power supply has an"H" followed by a "L". Which is correct? I've connected to the "L" but the laser appears always on.

  • I cant find a list or description of what the kits actually contain.. Pictures would be nice befor I spend 2 grand "The BlackTooth will be provided in kit form" is a bit limited.. Thank you

    For all of our kits, it is highly recommended that the instructions are completed read. This will determine if the customer has the ability to take on a project of this complexity.

    Depending on the specific blackTooth option purchased, the kits include the following (if the parts is listed in the instructions, it is included in the kit unless otherwise specified within the price option):

    - Structural components: Plexiglas panels and MDO structural parts that form the overall machine.
    - All of the hardware necessary to assembly the structural components and to fasten the electronics and laser components.
    - The electronic components to move and power the machine including power supplies, motors, drivers, interface and computer components if that option was purchased.
    - Laser components including laser tube, mirrors, lens, nozzle, air pump and mounts.
    - Mechanical components including drive pulleys, bearings, rails, and timing belts.

    Click the link to respond:
    I cant find a list or description of what the kits actually contain.. Pictures would be nice befor I spend 2 grand "The BlackTooth will be provided in kit form" is a bit limited.. Thank you

  • Do you have a larger kit for the Blacktooth Laser? I need a laser with at least 80watts of power.

    We have one in the works. It is a 4'x8' machine that will house the 80w laser tube on the gantry. The machine is bout 2 months out as of 1/7/2014.

    Click the link to respond:
    Do you have a larger kit for the Blacktooth Laser? I need a laser with at least 80watts of power.

  • looking for wiring schematic for redleaf electronics to huijang yl600 VFD 110v, 2.2k, thanks!

    It is possible to connect and configure the spindle VFD to the mach3 via an RS485 communication and protocol.

    The first thing you will need is the dynamic link library to pair with mach3 called the Huanyang VFD Mach3 PlugIn. You can find this file at the mach3 support forum here: http://www.machsupport.com/forum/index.php/topic,14182.0.html

    You will also need to download the Microsoft .net 3.5 framework and install it: https://www.microsoft.com/en-us/download/details.aspx?id=21

    Follow the pdf that comes with the library file, but here is a synopsis of what you need to do (I also added a lot more information that may be useful during this process as the manual does not cover the main connections that need to be done):

    You will need to program your VFD so that it knows how to communicate with mach3 and the computer (go into the programming mode of the VFD and change these parameters):
    - PD001 - value 2 - Enables with communication aspect of the VFD
    - PD002 - value 2 - Enables frequency control from the communcations port
    - PD163 - value 1 - VFD address
    - PD164 - value 1 - Baud rate of 9600 (speed of the communication)
    - PD165 - value 3 - 8N1 RTU - 8 bits (that's the size of the word that gets communicated), N (No parity or no error checking) and 1 (1 stop bit)

    Copy the dll file to the PlugIns folder of mach3.

    Connect the RX and TX lines to your computer. There are a couple ways you can do this, but the recommended way would be to use an FTDI USB device which converts a USB to a serial com port. The device will have Rx and Tx connectors to connect to the VFD terminals with the same labels. This method is recommended since serial ports are not as common in computers these days.

    Next, you will need to configure mach3 to use the plugin library. Start mach3 and click on Menu -> config ->Config Plugins. Enable the new plugin by clicking on the red cross on the left column next to the plug in. Restart mach3 after doing this.

    No you need to configure mach3 to use the HuanyangVFD plugin. Go to the ports & pins configuration and select the spindle setup tab. Make sure that the Disable Spindle Relays checkbox is unchecked. We don't want mach3 to output a signal for a relay since the spindle will start up and turn off within the VFD and not from an external relay.

    Next, go to the HuanyangVFD settings by clicking on Menu -> plugin control -> HuanyangVFD. Set the parameters to the same settings you put into the VFD programming. The com port will be shown as new hardward when you plug in the USB FTDI device. A little bubble will be displayed at the bottom right where it will notify you that a new device is being installed (be patient while windows assigns a com port). Alternatively, you can use the windows device manager to see which port was set for the new USB FTDI device). You may need to restart mach3 several times until you get the correct information displayed in the PD001 and PD002 fields. When the com port is correct and the other parameters, like baud and VFD address is the same as you entered in the programming, then the PD001 and PD002 will show the number 2, otherwise, a 99 will appear which means that communication was not successful.

    You can now control the on/off and RPM of the spindle using the RS485 communication between mach3 and the VFD.

    Additional Information:
    Will this work with the brand called "best "vfd as well.

    Click the link to respond:
    looking for wiring schematic for redleaf electronics to huijang yl600 VFD 110v, 2.2k, thanks!

  • I am assebling the Blacktooth CNC laser 20x24" with what appears to be an updated power supply. After refrencing the wiring diagram on line and the totorial, may I ask for an updated diagram or totorial, the current version do not appear to match match the configuration provided. I do not feel confidant in the educational guess, that I have. thanks

    Wiring diagrams for the Laser Power Supply will be mostly the same with the updated power supply. The main difference is the newer power supply contains a secondary green terminal block on the front of the power supply next where the hard leads are connected. This differs from the older power supply which had contact points on the back of the power supply. Please refer to the tutorials section for updated information and if you have specific questions please email techsupport@buildyourcnc.com

    Click the link to respond:
    I am assebling the Blacktooth CNC laser 20x24" with what appears to be an updated power supply. After refrencing the wiring diagram on line and the totorial, may I ask for an updated diagram or totorial, the current version do not appear to match match the configuration provided. I do not feel confidant in the educational guess, that I have. thanks

  • The electronics package I just bought from you (Book Build) is different from your wireing diagrams and video tutorials. Is there an updated wiring diagram available? Is the USB port on the breakout board connected directly to the computer USB to supply 5 volts? Thank you.

    For our parallel breakout board (https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay#prettyPhoto/2/) the schematic will show the connections going from the BB to the drivers. The parallel breakout board uses the 25 pin parallel connection to communicate from the computer to drivers, and the USB is used to power the main-board itself, supplying 5V.

    Click the link to respond:
    The electronics package I just bought from you (Book Build) is different from your wireing diagrams and video tutorials. Is there an updated wiring diagram available? Is the USB port on the breakout board connected directly to the computer USB to supply 5 volts? Thank you.

  • purchased assembled greenbull with electronics, need wiring diagram from rs485/breakout to VFD 110 v

    It is possible to connect and configure the spindle VFD to the mach3 via an RS485 communication and protocol.

    The first thing you will need is the dynamic link library to pair with mach3 called the Huanyang VFD Mach3 PlugIn. You can find this file at the mach3 support forum here: http://www.machsupport.com/forum/index.php/topic,14182.0.html

    You will also need to download the Microsoft .net 3.5 framework and install it: https://www.microsoft.com/en-us/download/details.aspx?id=21

    Follow the pdf that comes with the library file, but here is a synopsis of what you need to do (I also added a lot more information that may be useful during this process as the manual does not cover the main connections that need to be done):

    You will need to program your VFD so that it knows how to communicate with mach3 and the computer (go into the programming mode of the VFD and change these parameters):
    - PD001 - value 2 - Enables with communication aspect of the VFD
    - PD002 - value 2 - Enables frequency control from the communcations port
    - PD163 - value 1 - VFD address
    - PD164 - value 1 - Baud rate of 9600 (speed of the communication)
    - PD165 - value 3 - 8N1 RTU - 8 bits (that's the size of the word that gets communicated), N (No parity or no error checking) and 1 (1 stop bit)

    Copy the dll file to the PlugIns folder of mach3.

    Connect the RX and TX lines to your computer. There are a couple ways you can do this, but the recommended way would be to use an FTDI USB device which converts a USB to a serial com port. The device will have Rx and Tx connectors to connect to the VFD terminals with the same labels. This method is recommended since serial ports are not as common in computers these days.

    Next, you will need to configure mach3 to use the plugin library. Start mach3 and click on Menu -> config ->Config Plugins. Enable the new plugin by clicking on the red cross on the left column next to the plug in. Restart mach3 after doing this.

    No you need to configure mach3 to use the HuanyangVFD plugin. Go to the ports & pins configuration and select the spindle setup tab. Make sure that the Disable Spindle Relays checkbox is unchecked. We don't want mach3 to output a signal for a relay since the spindle will start up and turn off within the VFD and not from an external relay.

    Next, go to the HuanyangVFD settings by clicking on Menu -> plugin control -> HuanyangVFD. Set the parameters to the same settings you put into the VFD programming. The com port will be shown as new hardward when you plug in the USB FTDI device. A little bubble will be displayed at the bottom right where it will notify you that a new device is being installed (be patient while windows assigns a com port). Alternatively, you can use the windows device manager to see which port was set for the new USB FTDI device). You may need to restart mach3 several times until you get the correct information displayed in the PD001 and PD002 fields. When the com port is correct and the other parameters, like baud and VFD address is the same as you entered in the programming, then the PD001 and PD002 will show the number 2, otherwise, a 99 will appear which means that communication was not successful.

    You can now control the on/off and RPM of the spindle using the RS485 communication between mach3 and the VFD.

    Additional Information:
    Will this work with the brand called "best "vfd as well.

    Click the link to respond:
    purchased assembled greenbull with electronics, need wiring diagram from rs485/breakout to VFD 110 v

  • please send wiring diagram for the 1500kw spindle and inverter combo. i need to see what additional things need be purchased. thanks.

    Please refer to the Spindle wiring diagram found on the product page for the 2.2KW spindle. The wiring diagram will be the same for the 1.5kW Spindle. The only difference will depend on if you are using 110v or 220v power, as setting PD008 asks you to specify the max voltage.

    Click the link to respond:
    please send wiring diagram for the 1500kw spindle and inverter combo. i need to see what additional things need be purchased. thanks.

  • Is there a wiring diagram for hooking up your hex inverter between your USB breakout board and the controller?

    The use of the hex inverter in the application to invert a direction signal to have a motor run in the reverse directions is relatively simple.

    First, go to this link and look at the chip diagram:
    https://www.buildyourcnc.com/item/electronicsAndMotors-hex-inverter-breakout-newbiehack-integrated_circuits-hex-inverter

    Connect 5V from the USB interface tothe VCC pin. The pin on the keyboard jog header can be used. Connect the GND pin from the USB interface to the GND pin on the hex inverter. Connect the CW terminal from the USB interface to the 1A pin on the hex inverter. Connect the 1Y pin from the hex inverter to the driver.

    Additional Information:
    I got a question??? I am a dummy when it comes to cnc. I got 6040 1500kw water cold engraver 3 axis from china. I can not get anything out of them pertaining help they keep telling me the same thing over and over and over and I'm doing it and send them pictures that I know. Anyway email me a wiring diagram for the PRT 1500 watt spindle motor control box and has the emergency stop on and off switch manual PC and of course yhe screanm fultonsbusiness@gmail.com

    Additional Information:
    I got a question??? I am a dummy when it comes to cnc. I got 6040 1500kw water cold engraver 3 axis from china. I can not get anything out of them pertaining help they keep telling me the same thing over and over and over and I'm doing it and send them pictures that I know. Anyway email me a wiring diagram for the PRT 1500 watt spindle motor control box and has the emergency stop on and off switch manual PC and of course yhe screanm fultonsbusiness@gmail.com

    Click the link to respond:
    Is there a wiring diagram for hooking up your hex inverter between your USB breakout board and the controller?

  • Can you shortcut the usb controller that comes with the blacktooth laser to hardware reset it?

    The USB controller does not have a reset button installed on it.

    You have some alternate options however:
    - You can remove the USB connector and re-insert it.
    - Set the USB to use external 5v by removing the jumper near the USB connector, use a 5v wall adapter and install a switch along the 5v DC power line to turn it off then on. You can use a momentary push button switch to do this.

    Click the link to respond:
    Can you shortcut the usb controller that comes with the blacktooth laser to hardware reset it?

  • laser wont fire using the trocen awc...double checked wiring and all seems correct to diagram

    Is there a test button on the laser tube power supply? You can test the laser output by using the test button. This will help you determine if the laser tube is bad, or if you have wiring issues. Sometimes, wiring to he TL may not work as some controllers are set to active low, so you may need to wire the controller to TH instead.

    Additional Information:
    Additionally, the mA on the high tension line does not have any relationship to the digital trigger signal from the controller to the power supply.

    Click the link to respond:
    laser wont fire using the trocen awc...double checked wiring and all seems correct to diagram

  • I need to replace the fried electronics box for my 6090 wood router. Do you offer a play and play, no wiring required, kit? If yes, how much? If no, can you recommend one?

    Yes, we offer a CNC electronics assembled package called the redFly, redLead and redSprout. If you already have a computer, I would recommend the redFly. You would still need to add connectors to the ends of your motor cable.

    https://www.buildyourcnc.com/item/cnc-computer-system-redFly

    Click the link to respond:
    I need to replace the fried electronics box for my 6090 wood router. Do you offer a play and play, no wiring required, kit? If yes, how much? If no, can you recommend one?

  • where is the build manual for the blacktooth laser? online? I didnt get one with my machine

    For our machines our steps for the build process can be found on the actual machine page with images to reference (please read carefully all the instructions) (https://www.buildyourcnc.com/blackToothLaserCutterAndEngraver.aspx).
    You can get further help here (http://blacktoothlaser.blogspot.ca/2013/04/index-for-blacktooth-laser.html?view=sidebar) a post made by one of our customers!

    Click the link to respond:
    where is the build manual for the blacktooth laser? online? I didnt get one with my machine

  • Do you have a wiring diagram for your breakout board and the SuperPID?

    It is not necessary for a wiring diagram for the breakout board to the SuperPID controller since you are only going to connect two wires from the breakout board output terminals of your choosing to the SuperPID controller. The only thing remaining is to configure Mach3 so that the spindle control section serves as the SuperPID controller.

    To setup this configuration in Mach3, go to your ports and pins dialog box (config menu -> ports and pins). Click on the spindle setup tab. In the Motor Control Section of the dialog, check the box for Use Spindle Motor Output and check the box for PWM control. Change the PWM Base Frequency to 50Hz.

    Click the link to respond:
    Do you have a wiring diagram for your breakout board and the SuperPID?