when a 4 or 5 axes machine?

Question #: 789

Question: when a 4 or 5 axes machine?

Current Solution

It's on the list of high priority next machines. The existing machines can already do 4 axes, you will need a head stock and tail stock. The head stock must be able to accept a stepping motor of the choice you require.

Respond:

Other Possible Solutions to this Question

HOW DO I SQUARE MY CNC MACHINE OR GANTRY?
I use a standard large "L" square used in construction. I run gantry up and down with the bit along one side of the square to make the square aligned with the x-axis. I then run the bit along the other edge and if I see space from the edge of the bit to the square, I adjust the gantry square by loosening and tightening the eye bolts that hold the chain at the ends of the table. Repeat as necessary to get the desired square.

Additional Information:
Click the link to add information to this solution:
HOW DO I SQUARE MY CNC MACHINE OR GANTRY?
Is the blacktoe a 4'x8' machine
The blacktoe machine is the one shown here: http://www.buildyourcnc.com/Item/cnc-machine-blacktoe-v4-2x4
Click the link to add information to this solution:
Is the blacktoe a 4'x8' machine
Is the blacktoe a 4'x8' machine
The blackToe CNC router is a 2'x4' (24"x48" medium format) machine. The blackFoot CNC Router is a 4'x8' (48" x 96" large format) machine.
Click the link to add information to this solution:
Is the blacktoe a 4'x8' machine
WHICH MACHINE SHOULD I BUY, GREENBULL OR BLACKFOOT?
The greenBull can range is routing width sizes of 5 feet and 6 feet. The blackFoot has a 4 foot routing width.

Previous Solution:
The greenBull machine has a sturdier gantry than the blackFoot, so you can be more agressive with the cutting feedrate (cutting speed). The blackFoot is also a good machine, but it all comes down to the speed at which you want to produce the fabrication

The spindle is also highly recommended for it's quietness and easier cleanup (no fan blowing the dust in the air)

Additional Information:

Additional Information:
Click the link to add information to this solution:
WHICH MACHINE SHOULD I BUY, GREENBULL OR BLACKFOOT?
WHICH MACHINE SHOULD I BUY, THE GREENBULL OR BLACKFOOT?
The greenBull can range is routing width sizes of 5 feet and 6 feet. The blackFoot has a 4 foot routing width.

Previous Solution:
The greenBull machine has a sturdier gantry than the blackFoot, so you can be more agressive with the cutting feedrate (cutting speed). The blackFoot is also a good machine, but it all comes down to the speed at which you want to produce the fabrication

The spindle is also highly recommended for it's quietness and easier cleanup (no fan blowing the dust in the air)

Additional Information:

Additional Information:
Click the link to add information to this solution:
WHICH MACHINE SHOULD I BUY, THE GREENBULL OR BLACKFOOT?
SHOULD I SELECT THE GREENBULL OR BLACKFOOT CNC MACHINE?
The greenBull can range is routing width sizes of 5 feet and 6 feet. The blackFoot has a 4 foot routing width.

Previous Solution:
The greenBull machine has a sturdier gantry than the blackFoot, so you can be more agressive with the cutting feedrate (cutting speed). The blackFoot is also a good machine, but it all comes down to the speed at which you want to produce the fabrication

The spindle is also highly recommended for it's quietness and easier cleanup (no fan blowing the dust in the air)

Additional Information:

Additional Information:
Click the link to add information to this solution:
SHOULD I SELECT THE GREENBULL OR BLACKFOOT CNC MACHINE?
WHAT IS THE DIFFERENCE IN A 2.5 AXIS MACHINE?
An axis is a direction of motion controlled by the CNC machine control. It can be linear (motion along a straight line) or circular (a rotary motion). The number of axes a machine has determines it's machining capabilities. A 2.5 axis machine really has three moving axes, but only two axes can move together (most machines sold today are full three axis machines). For machining centers, a three axis machine will have three linear axes. A four or five axis machine will have three linear axes as well as one or two rotary axes.

Note that 2.5 versus 3 axis has yet another context. 2.5 axis machining requires that the machine have three axes, but only two axes must be moving simultaneously at any one time. (Simple operations, like drilling and most milling, fall into this category). On the other hand 3-axis machining requires that all three axes be moving at the same time (More complex operations, like the machining of sculptured surfaces required in molds and airfoils, fall into this category.)

Additional Information:

Additional Information:
Click the link to add information to this solution:
WHAT IS THE DIFFERENCE IN A 2.5 AXIS MACHINE?
HOW DO I CALIBRATE MY MACHINE?
In Mach3, go to the Settings Tab, and select "Set Steps Per Unit". It will ask you how far to move the machine. Before you do this, make a mark on the table exactly where the end mill is resting. You can do this by lowering the end mill until it touches the material, then spinning it by hand to cut a small dimple in the material. Then, raise the end mill to clear the material, and assign a distance to move the machine. Once the machine moves and stops, measure the exact distance that it actually traveled with a tape measure, and enter this value into the dialog box that asks how far it moved. Mach3 will automatically adjust your steps per unit for that axis to be more accurate. Do this for all axes often to ensure you are cutting accurately. The longer distances you use calibrate, and the more precise you are with your measurements, the better.
Click the link to add information to this solution:
HOW DO I CALIBRATE MY MACHINE?
PARTS LIST FOR THE BOOK MACHINE
The parts list is located on this page: http://buildyourcnc.com/cnckitintro.aspx at the bottom of the description.

Additional Information:

Additional Information:
Click the link to add information to this solution:
PARTS LIST FOR THE BOOK MACHINE
MY MACHINE NOT ACCURATE
In Mach3, go to the Settings Tab, and select "Set Steps Per Unit". It will ask you how far to move the machine. Before you do this, make a mark on the table exactly where the end mill is resting. You can do this by lowering the end mill until it touches the material, then spinning it by hand to cut a small dimple in the material. Then, raise the end mill to clear the material, and assign a distance to move the machine. Once the machine moves and stops, measure the exact distance that it actually traveled with a tape measure, and enter this value into the dialog box that asks how far it moved. Mach3 will automatically adjust your steps per unit for that axis to be more accurate. Do this for all axes often to ensure you are cutting accurately. The longer distances you use calibrate, and the more precise you are with your measurements, the better.
Click the link to add information to this solution:
MY MACHINE NOT ACCURATE
HOW DO I MAKE MY MACHINE SQUARE?
I use a standard large "L" square used in construction. I run gantry up and down with the bit along one side of the square to make the square aligned with the x-axis. I then run the bit along the other edge and if I see space from the edge of the bit to the square, I adjust the gantry square by loosening and tightening the eye bolts that hold the chain at the ends of the table. Repeat as necessary to get the desired square.

Additional Information:
Click the link to add information to this solution:
HOW DO I MAKE MY MACHINE SQUARE?
HOW LONG WOULD IT TAKE FOR MY TO BUILD A MACHINE?
The length of time it will take to build a CNC machine kit is not an easy answer. There may be a wide array of circumstances that limit a persons abilities to build the cnc machine kit in an efficient timeframe; however, if you have moderate dexterity and moderately mechanically inclined, you should have no problem building one of our machines within one weekend if the project has very little downtime.

Additional Information:
Click the link to add information to this solution:
HOW LONG WOULD IT TAKE FOR MY TO BUILD A MACHINE?
WHAT IS CNC MACHINE?
A CNC machine is basically a computer controlled high precision tool that is able to make intricate movements accurately and repeatedly. Our machines use common routers and spindles to mill, cut, engrave and shape materials in automated machining operations.
Click the link to add information to this solution:
WHAT IS CNC MACHINE?
WHAT NOT INCLUDED WITH THE MACHINE?
PC with parallel port and USB port
20awg stranded wires for the motors - http://www.buildyourcnc.com/electronicscombo.aspx
18awg stranded wires for power supply to drivers
24awg stranded wires for breakout board to drivers
(location and spacing of components varies from one person to another, so we do not provide cables/wires)
- General purpose extension cord (cut the female end off) to provide power to power supply
- USB cable to power breakout board
- Parallel cable to communicate to breakout board
- Router
- (optional - instead of router) Spindle with power inverter http://www.buildyourcnc.com/SpindlesAndAccessories.aspx
- (if purchasing spindle with inverter) General purpose extension cord (240v) (cut the female end off) to provide power to power inverter
- End Mill(s) http://www.buildyourcnc.com/ProductsEndMills.aspx
- CAD, and/or CAD-CAM software (to produce geometry, machine operations, and g-code) http://www.buildyourcnc.com/CNCsoftware.aspx
- CNC control software (to read g-code and control machine) http://www.buildyourcnc.com/CNCsoftware.aspx
- If the machine does not have the table included, then a table will need to be built. The rails, chain and chain mounts are included that are used on this table.

Additional Information:
Click the link to add information to this solution:
WHAT NOT INCLUDED WITH THE MACHINE?
WHAT KIND OF MATERIALS CAN MACHINE?
There are almost no limits to the kind of materials you can machine. Anything from wood or plastic to exotic materials like stainless steel can be cut as long as the part can be safely and firmly held and the proper cutting tool and cutting speed are used
Click the link to add information to this solution:
WHAT KIND OF MATERIALS CAN MACHINE?
WHAT WOULD NEED TO HAVE A FULLY OPERATIONAL MACHINE?
PC with parallel port and USB port
20awg stranded wires for the motors - http://www.buildyourcnc.com/electronicscombo.aspx
18awg stranded wires for power supply to drivers
24awg stranded wires for breakout board to drivers
(location and spacing of components varies from one person to another, so we do not provide cables/wires)
- General purpose extension cord (cut the female end off) to provide power to power supply
- USB cable to power breakout board
- Parallel cable to communicate to breakout board
- Router
- (optional - instead of router) Spindle with power inverter http://www.buildyourcnc.com/SpindlesAndAccessories.aspx
- (if purchasing spindle with inverter) General purpose extension cord (240v) (cut the female end off) to provide power to power inverter
- End Mill(s) http://www.buildyourcnc.com/ProductsEndMills.aspx
- CAD, and/or CAD-CAM software (to produce geometry, machine operations, and g-code) http://www.buildyourcnc.com/CNCsoftware.aspx
- CNC control software (to read g-code and control machine) http://www.buildyourcnc.com/CNCsoftware.aspx
- If the machine does not have the table included, then a table will need to be built. The rails, chain and chain mounts are included that are used on this table.

Additional Information:
Click the link to add information to this solution:
WHAT WOULD NEED TO HAVE A FULLY OPERATIONAL MACHINE?
WHAT ELSE DO I NEED WITH THE MACHINE?
PC with parallel port and USB port
20awg stranded wires for the motors - http://www.buildyourcnc.com/electronicscombo.aspx
18awg stranded wires for power supply to drivers
24awg stranded wires for breakout board to drivers
(location and spacing of components varies from one person to another, so we do not provide cables/wires)
- General purpose extension cord (cut the female end off) to provide power to power supply
- USB cable to power breakout board
- Parallel cable to communicate to breakout board
- Router
- (optional - instead of router) Spindle with power inverter http://www.buildyourcnc.com/SpindlesAndAccessories.aspx
- (if purchasing spindle with inverter) General purpose extension cord (240v) (cut the female end off) to provide power to power inverter
- End Mill(s) http://www.buildyourcnc.com/ProductsEndMills.aspx
- CAD, and/or CAD-CAM software (to produce geometry, machine operations, and g-code) http://www.buildyourcnc.com/CNCsoftware.aspx
- CNC control software (to read g-code and control machine) http://www.buildyourcnc.com/CNCsoftware.aspx
- If the machine does not have the table included, then a table will need to be built. The rails, chain and chain mounts are included that are used on this table.

Additional Information:
Click the link to add information to this solution:
WHAT ELSE DO I NEED WITH THE MACHINE?
IS DRILL BIT USED IN THE CNC MACHINE?
The cutting tool is an end mill (it looks like a drill bit). It is a cutting tool that can plunge and cut sideways. That item is not included and is a consumable. You will purchase these very frequently and will have geometry that is very specific to how you apply the cnc machine.

Additional Information:
Click the link to add information to this solution:
IS DRILL BIT USED IN THE CNC MACHINE?
MY MACHINE CUTTING THE WRONG SIZE PART
In Mach3, go to the Settings Tab, and select "Set Steps Per Unit". It will ask you how far to move the machine. Before you do this, make a mark on the table exactly where the end mill is resting. You can do this by lowering the end mill until it touches the material, then spinning it by hand to cut a small dimple in the material. Then, raise the end mill to clear the material, and assign a distance to move the machine. Once the machine moves and stops, measure the exact distance that it actually traveled with a tape measure, and enter this value into the dialog box that asks how far it moved. Mach3 will automatically adjust your steps per unit for that axis to be more accurate. Do this for all axes often to ensure you are cutting accurately. The longer distances you use calibrate, and the more precise you are with your measurements, the better.

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:
idwmHJym

Additional Information:
-1 OR 2+78-78-1=0+0+0+1 --

Additional Information:
-1 OR 2+135-135-1=0+0+0+1

Additional Information:
-1' OR 2+886-886-1=0+0+0+1 --

Additional Information:
-1' OR 2+357-357-1=0+0+0+1 or 'xkLzGxAb'='

Additional Information:
-1" OR 2+279-279-1=0+0+0+1 --

Additional Information:
1'"

Additional Information:
1��%2527%2522

Additional Information:
@@5fZce

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:
Click the link to add information to this solution:
MY MACHINE CUTTING THE WRONG SIZE PART