[ Log In ]
[ Register ]
NEW: CNC Router PLANS Available for all of our Newest CNC Models!! Click here to "Design Your CNC".

Question #: 829

Question: your usb breakout board will work the latest version of planet cnc software?

Current Solution

Yes, our USB controller will work on the latest version of Planet-CNC.

Respond:

Other Possible Solutions to this Question

  • will mach4 software work with planet CNC breakoutboard?

    Our USB breakout board, will not work with Mach 4! The USB BoB is specifically designed to work with Planet-CNC.

    Click the link to respond:
    will mach4 software work with planet CNC breakoutboard?

  • In a Windows configuration, Using the USB breakout board, is the Planet-CNC software used in conjunction with Mach3 or in place of it?

    Mach3 is not compatible with the USB breakout board, so you need Planet CNC in its place.

    Additional Information:

    I am confused by this same issue. I am using the Mach3 USB interface board with Mach3 and it works fine. In fact a video of it is on this very website. (link below)

    Is the Mach3 USB interface board the same thing as Planet-CNC USB board?
    It has been stated on this FAQ that it cannot be used with Mach3 and can only be used with Planet CNC USB software.

    https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

    Click the link to respond:
    In a Windows configuration, Using the USB breakout board, is the Planet-CNC software used in conjunction with Mach3 or in place of it?

  • I have the older discontinued USB breakout board. The y-axis no longer works and have traced it to the breakout board. Is there a replacement board that can use the same Planet CNC software running on Windows 10?

    No, we have gotten away from the planet-cnc boards as they have decided to not support our board with their software. You can use the Mach3 USB board as an alternative. You will be better off with Mach3 as a control software as this is widely used and supported.

    Mach3 USB board:
    https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

    Click the link to respond:
    I have the older discontinued USB breakout board. The y-axis no longer works and have traced it to the breakout board. Is there a replacement board that can use the same Planet CNC software running on Windows 10?

  • How do I get Homing on Z to work with Plate and Ground using Buildyourcnc usb board all the entries for the sensor in planet-cnc are grayed out. I am using input z- and I purchased the software

    To home the z-axis using a plate:
    - Connect the end mill using a large clamping device like an alligator clip with a wire connected to GND.

    - Connect the plate (solder a wire to the plate) to one of the input pins.

    - You can use the autoset to setup that pin in Mach3 simply by touching the two together once connected to the pin and GND.

    Alternatively, the end mill can be connected to the pin and the plate connected to GND as long as there becomes a complete circuit when the end mill touches the plate.

    To setup homing for the Planet-CNC homing and limits, go to the Planet-CNC Machine setup page which explains the process step by step: http://www.planet-cnc.com/faq/machine_setup/

    Customer Response:
    How do I get homing on z to work with planet cnc software using build your own usb board. I have gone to planet website and followed the instructions provided but my software will not allow entries in the required fields they are grayed out is it because I am not using planet-cnc's board, I have used this method for years with Mach3 and would like to use it with the usb board and software.

    Answer:
    Just received information from the developer. The instructions on how to use a plate for z-axis homing (moveable sensor) can be found here:

    http://www.planet-cnc.com/faq/moveable_sensor/

    Click the link to respond:
    How do I get Homing on Z to work with Plate and Ground using Buildyourcnc usb board all the entries for the sensor in planet-cnc are grayed out. I am using input z- and I purchased the software

  • However it how do I get the software to work? PlanetCNC sent me a key that looks like it will only work with a backup control board I purchased from them?

    When you plug the USB controller into the computer using a USB cable, and the planet-cnc software is running, you will be presented with a dialog box that will contain a text box for the key that you received from the planet-cnc folks.

    Additional Information:


    Additional Information:
    Is there any other software that will work with your controller Mach3? Thanks for the help!

    Click the link to respond:
    However it how do I get the software to work? PlanetCNC sent me a key that looks like it will only work with a backup control board I purchased from them?

  • Has anyone at BuildYourCnc ever tested homeing the z axis using a plate and ground clip using their BuildYourCnc usb breakout Board and a registered copy of Planet-Cnc software. If the answer is yes could they provide instruction from BuildYourCnc and not Planet-Cnc as their instruction does not work with BuildYourCnc USB breakout Board.

    Planet-cnc is the best place to get information on setting up the software for the USB interface. We will test the z-axis plate homing method on Monday to be able to provide a more thorough explanation.

    Click the link to respond:
    Has anyone at BuildYourCnc ever tested homeing the z axis using a plate and ground clip using their BuildYourCnc usb breakout Board and a registered copy of Planet-Cnc software. If the answer is yes could they provide instruction from BuildYourCnc and not Planet-Cnc as their instruction does not work with BuildYourCnc USB breakout Board.

  • does the planet cnc software come with the usb board on the 3: disc?

    Can you clarify what 3: disc? Thanks.

    Click the link to respond:
    does the planet cnc software come with the usb board on the 3: disc?

  • How do i get the USB break out board to communicate with the exceptional Planet-CNC USB software?

    The USB interfaces (The board shown at the link: https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-USB-Controller-Breakout) that we well is already updated with the firmware, and tested with the planet-cnc software. Simply install the planet-cnc software and plug in the USB interface and the software will communicate with the board.

    Additional Information:
    Windows 10 was not allowing the planet cnc software to install the proper drivers. Following the windows 8 reccomendations listed on the usb break out board page got the planet cnc and usb break out board communicating.

    Click the link to respond:
    How do i get the USB break out board to communicate with the exceptional Planet-CNC USB software?

  • How do you zero the z axis using a plate with the planet-cnc software and your USB controller?

    The instructions on how to use a plate for z-axis homing (moveable sensor) can be found here:

    http://www.planet-cnc.com/faq/moveable_sensor/

    Click the link to respond:
    How do you zero the z axis using a plate with the planet-cnc software and your USB controller?

  • I have the usb breakout board https://buildyourcnc.com/Item/electronicsAndMotors-electronic-component-USB-Controller-Breakout and need to run the A axis as a slave the software greys out the box how do I fix this?

    You will need PlanetCNC software for the USB breakout board and when plugging in the USB the computer should automatically recognize the board, however you can go into device manager to see if the USB terminal is working correctly.
    The parallel breakout board; the USB is not a connection terminal rather than a power source, and the parallel port will be the communication terminal.
    The items you will need for a water cooled spindle would be: water pump, silicon tubing(length desired by customer), a extension cord(from a hardware store(orange))(1 same gauge wire/length as extension cord).

    Click the link to respond:
    I have the usb breakout board https://buildyourcnc.com/Item/electronicsAndMotors-electronic-component-USB-Controller-Breakout and need to run the A axis as a slave the software greys out the box how do I fix this?

  • Using USB Controller Board with Planet-CNC software. The S/W recognizes limit switches but not soft limits. Help?

    "Soft limits are used to decelerate machine to stop before machine is stopped hard way at limit switch or before it crashes. I recommend "Soft Limits Decelerate" and "Soft Limits Strict" settings are also checked. Sometimes we need to disable soft limits and there is a command for this in menu "Machine/Soft Limits". When soft limit is triggered position display will be yellow."

    Are the soft limits "grayed out"?
    Here is a link to a very useful forum post from the Planet-CNC crew:
    http://www.planet-cnc.com/faq/machine_setup/

    Click the link to respond:
    Using USB Controller Board with Planet-CNC software. The S/W recognizes limit switches but not soft limits. Help?

  • I AM USING USB BREAKOUT BOARD WITH PLANET-CNC SOFTWARE. WHEN ENABLE JOGGING KEYBOARD X AXIS STARTS TO MOVE BY ITSELF (WHETHER CONNECTED OF NOT). PRESS STOP - IT STOPS FOR A MOMENT AND THEN AGAIN. WHAT COULD THAT BE? TRIED REINSTALL SOFTWARE DID NOT HELP.

    It seems to be getting some kind of interference or a short within the wiring or communication, try jogging the motors in the software without anything wired to the board. Then add one motor at a time to see if there is a short within your wiring or a faulty driver/motor.
    If the USB breakout board continues to move the x-axis with no motors or driver wired to it, please email customerservice@buildyourcnc.com for a replacement or further troubleshooting.

    Click the link to respond:
    I AM USING USB BREAKOUT BOARD WITH PLANET-CNC SOFTWARE. WHEN ENABLE JOGGING KEYBOARD X AXIS STARTS TO MOVE BY ITSELF (WHETHER CONNECTED OF NOT). PRESS STOP - IT STOPS FOR A MOMENT AND THEN AGAIN. WHAT COULD THAT BE? TRIED REINSTALL SOFTWARE DID NOT HELP.

  • Will the Mach 3 USB breakout board work with a Windows 7 64 bit system?

    I don't see why Mach3 under windows 64-bit wouldn't work with an interface that uses USB as it's primary communication method. I am a bit vague on this, so I will do more research on it.

    We recommend Mach3 run under Windows 32-bit when using the parallel interface as this is a legacy function.

    Additional Information:


    Additional Information:
    mach 3 usb board setup

    Additional Information:
    I am running Mach3 under Windows 7 Pro 64bit without any problems.

    Additional Information:


    Additional Information:

    Click the link to respond:
    Will the Mach 3 USB breakout board work with a Windows 7 64 bit system?

  • I have your USB controller sitting here and want to control it with something other than PlanetCNC control software?

    The USB controller will only work with the Planet-CNC software. This software is well made and will provide great functionality. The planet-cnc software delivers instructions to the microcontroller on the board and the microcontroller will send out the pulse trains needed to move the machine correctly.

    There are two main alternatives if you want to use the mach3 software:
    First, get a parallel port card and add it to your computer and get a parallel breakout board. If you have a laptop/notebook computer, this will not be possible.
    Second, if you have a laptop, or really want to use the USB as the main interface for controlling the machine, you will need to get the smoothstepper board which works with mach3. The price combination is much higher than the USB controller with planet-cnc, but will work with Mach3.

    Additional Information:


    Additional Information:


    Additional Information:
    The planet cnc controller can be prone to electrical interference and has been known to cause such problems. In the first instance try to use a quality double sheilded USB cable, hopefully this will fix your problem. Alternatively you may need to sheild your limit switch, estop and or motor cabling. My pick is that a quality USB cable will fix it though, worked for me.

    Click the link to respond:
    I have your USB controller sitting here and want to control it with something other than PlanetCNC control software?

  • I want to use Planet-CNC software can I use Mach3 USB Board

    Planet-CNC is the control software. If you decide to use the USB controller, you will need to use the planet-CNC software as the control software. You will be able to use any of the CAM software applications with the planet-CNC control software.

    Click the link to respond:
    I want to use Planet-CNC software can I use Mach3 USB Board

  • I purchased the USB BOB and the link for the Planet-cnc software is broke. Will I need to purchase a license for the software as well?

    Here is the new link to the Planet CNC software download page: http://planet-cnc.com/software/

    You can try the software as a demo however you will have limited g-code lines you can run. I believe it was around 500, so you can create small items with the demo.
    To fully unlock the Planet-CNC software you will need to purchase the license.

    Click the link to respond:
    I purchased the USB BOB and the link for the Planet-cnc software is broke. Will I need to purchase a license for the software as well?

  • Do the 5 Axis Breakout Board with Relay requires software to setup

    The breakout board does not require software to run, specifically. The breakout board serves only as a signal conditioner where the input signal from the computer is output at the corresponding terminal, or the terminal receives a signal and is conditioned and sent to the parallel connector to be read by the computer. As long as the software can communicate to the parallel port of the computer, then the breakout board will function.

    Click the link to respond:
    Do the 5 Axis Breakout Board with Relay requires software to setup

  • sorry, this is what i meant to say: OK, so if I use the USB version then I would find the rotary/linear axis definitions in the planet cnc control software somewhere. I will be needing to change axis type often for various projects that is why I am asking.

    You can download a trial version of PlanetCNC software from their site at http://www.planet-cnc.com/index.php?page=software to see how you like the interface. If you look at their main GUI screen, along the left side you will see 4 boxes labeled X,Y,Z and A. These represent the axes the software is equipped to control. (A being Axial, or rotational motion) Typically a separate motor and driver is used to control each axis. If you plan to switch axes you will need to connect and disconnect the outputs from your software to the drivers.

    Click the link to respond:
    sorry, this is what i meant to say: OK, so if I use the USB version then I would find the rotary/linear axis definitions in the planet cnc control software somewhere. I will be needing to change axis type often for various projects that is why I am asking.

  • WILL THE USB BREAKOUT BOARD WORK WITH MACH3?

    Sure, the USB interface has a place for 4 axes of limit switches.

    Each axis can have two limit switches: one for the ++ (positive) end and one for the -- (negative) end. The positive end would be the limit switch at the end of the machine that, say the machine has a 4'x8' area, reaches a bit after the 8 foot mark. The negative end would be the limit switch behind the 0 foot location behind the origin. If the origin is in the middle, the negative would be at a little more than the -4 foot end and the positive would be at a bit more than the +4 foot end. Note that you can have more than one switch on each pin where the NC is connected in serial fashion and the NO is connected in parallel fashion (this can be seen on the diagram in the multiple limits switch section). The software configurations for the limits switches are under File -> Settings -> Limit.

    A typical limit switch has three connections on it. These connections consist of COM (common), NC (normally closed) and NO (normally open). The COM would generally go to GND and the NC or the NO would go to the pin. If the NC is used, then the the switch is constantly connected until the switch is pushed (engaged) then the connection from the pin to gnd is broken (open). Use the settings in software to set whether in NC or NO configuration.

    Let me know if this information was helpful (or not) by adding information to this question. Thanks.

    User response:
    Thank you very much for this helpful information. I'm still a little fuzzy on how the 6 limit switches physically connect to each other and to the USB breakout board. You've stated one switch (home) goes to positive and another switch (limit) goes to negative. Are all the GND prongs from all 6 switches connected to each other and going to GND on the breakout board, or no? And the NC prongs, how exactly are they connected to each other? And to the board? There has to be a diagram somewhere shows this visually, no? I don't know how to wire the switches in series or in parallel. I have already physically installed all the switches on the machine and ran the wires to where the board is. Now I just need to know where to plug these wires into the board. Also, taking into consideration that I'm using the Planet CNC software, the only settings I have pertaining to limit switches is "Enable/Disable" for each axis, and the actual limit for each axis. Nothing about NC or NO. Is that only in Mach3?
    Thank you.

    buildyourcnc response:
    On the USB interface, the COM on the switch connects to GND and the NC or NO connects to the input pin (i.e. x++, y--, etc.)

    Limit switch configuration is rather difficult to understand, especially with series and parallel. You can think of series as a single wire going from GND to the axis letter input terminal (i.e. X++ or X--). If the wire is broken, then the circuit is open (or the switch is engaged in a normally closed scenario). Normally closed is like an actual wire, and when engaged, the switch "opens" (breaks the wire). This is why we recommend in some systems that you can put many switches in series on a single pin. When one of the switches is engaged (breaking the connection) then the entire circuit of switches is broken and the machine stops.

    In a parallel scenario, the state of the circuit is always broken until the one of the switches is engaged and the circuit is then closed or connected. The topology looks like a ladder. All the switches connect to both sides of the ladder and the switches are like the runs of the ladder (the horizontal bars that the feet are placed while climbing). Imagine all of the switches broken in this scenario (normally open). It would be like the ladder could be split in two, but if one of the ladder runs (switches) is closed by engaging it, then that run would connect both sides of the ladder and the two sides of the ladder would have a connection.

    There is a diagram on the USB page of the various limit switch configurations. If you need more information (visual and/or otherwise), please let us know and we will immediately add that information to benefit everyone.

    Click the link to respond:
    WILL THE USB BREAKOUT BOARD WORK WITH MACH3?