Does the Green lean CNC 4'X8' cut 3D?

Question #: 1140

Question: Does the Green lean CNC 4'X8' cut 3D?

Current Solution

Yes, the greenLean can do the same type of machining as any other 3 axis CNC machine or CNC router. With 3D machining using a 3 axis CNC machine, 3D carvings can be done; however, no undercuts can be carved as the end mill (carving tool) is constantly perpendicular to the workpiece.

A 4th axis headstock and tailstock can be added to the machine for more precise 3D carvings and the greenLean can have these 4th axis units mounted within the structural ribs.

Respond:

Other Possible Solutions to this Question

HOW MUCH SILICONE TUBE DO I NEED FOR A GREEN LEAN TO CONNECT THE SPINDLE
The greenlean requires 56 feet of 1/4 Inside Diameter and 3/8 Outside Diameter silicon tube for the spindle.

Additional Information:
20

Additional Information:
20
Click the link to add information to this solution:
HOW MUCH SILICONE TUBE DO I NEED FOR A GREEN LEAN TO CONNECT THE SPINDLE
Hi - what is the cost of shipping the lean to CNC to the UK (8'x4')
You can determine if the country is serviceable by:
- selecting the items you want to purchase on the website
- go to the cart (shopping cart top left of any webpage)
- log in, or register
- Enter the address and click on calculate shipping.

The webpage will return the direct rates and whether your area is serviced or not. Feel free to enter any address as long as you are able to receive the package from that address.

The shipping times are determined by the service you select in the shopping cart. If a machine is purchased, we generally have a one week lead time unless otherwise stated in the description of the machine's product page.

Additional Information:
Click the link to add information to this solution:
Hi - what is the cost of shipping the lean to CNC to the UK (8'x4')
can the greenBull Kit CNC machine cut HDPE Seaboard?
The greenBull can cut HDPE Seaboard, and other materials as well. The machine will be cutting with either a router/spindle(customer preference) and will be the greatest aspect of actual cutting of material, to get a good overall coverage of materials. Our 2.2kW spindle will be the best option for a large variety of materials.
Click the link to add information to this solution:
can the greenBull Kit CNC machine cut HDPE Seaboard?
WHAT MOTORS DOES THE BLACK TOOTH USE?
Nema 23 stepping motors with 100 oz-in rated holding torque and 1/4" shaft.
Click the link to add information to this solution:
WHAT MOTORS DOES THE BLACK TOOTH USE?
WHAT MOTORS DOES THE BLACK TOOTH USE?
Nema 23 stepping motors with 100 oz-in rated holding torque and 1/4" shaft.
Click the link to add information to this solution:
WHAT MOTORS DOES THE BLACK TOOTH USE?
DOES THE SOFTWARE WORK ON AN APPLE?
There are several CAD/CAM programs out there for MacOS. Here is a list of a few: http://www.macuser.de/forum/f53/3d-2d-cad-395058/#post4499316
I've also read good things about punchCAD: http://www.punchcad.com/
Of course, there is always SketchUp if you are in a pinch. There are a few CAM plugins for SketchUp as well, but I've never used them, so I can't vouch for them.

CAD/CAM will get you as far as designing your parts and producing the g-code, but if you also want to run the CNC machine with your Mac, you will need a piece of software similar to Mach3 or EMC to run the g-code. I haven't been able to find anything like these programs that runs on Mac, so you may have to run Mach3 or EMC in Windows using Boot Camp or a virtual machine such as VMware or Parallels.

Personally, I would use the Mac to do all the CAD/CAM, then use a cheap PC to run the CNC machine.

Additional Information:

Additional Information:
EasyDNC for OSX
www.dnc-x.com

Additional Information:

Additional Information:
Hi guys I’m new to the cnc and I’m beginning to learn how to operate and cad-cam software also my cnc runs on Mach3 my questions is if I should use MacBook to do all designs if I can have all this software to run on Mac or I have to use windows software to operate it? I have separate small computer connected to the cnc table who have Mach3 on it please help. Also if you know any other software much easy for beginners please let me know thank you guys!
My email if needed is r1jastrzebski@gmail.com

Additional Information:

Additional Information:
Hi , thank you for your advise!

Additional Information:
Hi , thank you for your advise!

Additional Information:
Hi , thank you for your advise!

Additional Information:
Hi , thank you for your advise!

Additional Information:
Click the link to add information to this solution:
DOES THE SOFTWARE WORK ON AN APPLE?
DOES THE SOFTWARE WORK ON A MAC?
There are several CAD/CAM programs out there for MacOS. Here is a list of a few: http://www.macuser.de/forum/f53/3d-2d-cad-395058/#post4499316
I've also read good things about punchCAD: http://www.punchcad.com/
Of course, there is always SketchUp if you are in a pinch. There are a few CAM plugins for SketchUp as well, but I've never used them, so I can't vouch for them.

CAD/CAM will get you as far as designing your parts and producing the g-code, but if you also want to run the CNC machine with your Mac, you will need a piece of software similar to Mach3 or EMC to run the g-code. I haven't been able to find anything like these programs that runs on Mac, so you may have to run Mach3 or EMC in Windows using Boot Camp or a virtual machine such as VMware or Parallels.

Personally, I would use the Mac to do all the CAD/CAM, then use a cheap PC to run the CNC machine.

Additional Information:

Additional Information:
EasyDNC for OSX
www.dnc-x.com

Additional Information:

Additional Information:
Hi guys I’m new to the cnc and I’m beginning to learn how to operate and cad-cam software also my cnc runs on Mach3 my questions is if I should use MacBook to do all designs if I can have all this software to run on Mac or I have to use windows software to operate it? I have separate small computer connected to the cnc table who have Mach3 on it please help. Also if you know any other software much easy for beginners please let me know thank you guys!
My email if needed is r1jastrzebski@gmail.com

Additional Information:

Additional Information:
Hi , thank you for your advise!

Additional Information:
Hi , thank you for your advise!

Additional Information:
Hi , thank you for your advise!

Additional Information:
Hi , thank you for your advise!

Additional Information:
Click the link to add information to this solution:
DOES THE SOFTWARE WORK ON A MAC?
DOES THE SPINDLE RUN ON A 50HZ POWER SOURCE?
The spindle inverter (VFD) will run on a 220V (or between 170V-250V) power source with either 50Hz or 60Hz.
Click the link to add information to this solution:
DOES THE SPINDLE RUN ON A 50HZ POWER SOURCE?
what does the plans, hardware, electronics and mechanical option consists of for a CNC router?
The plans/hardware/electronics/mechanical includes everything but the wood structural components that can be cut by the customer. This plans/hardware option includes all of the electronics, like motors, drivers, controller, and all of the cables and wires to connect all of the electronics together. The mechanical components include shafts, couplings, linear rails, bearing blocks, sprockets, lead screws, etc. The hardware consists of all of the screws nuts, insert nuts, cross dowels, etc, to assemble all of the structural, mechanical, and electronics together.
Click the link to add information to this solution:
what does the plans, hardware, electronics and mechanical option consists of for a CNC router?
Do you have a CNC machine plan available for a 4'x8' machine?
All of our machines that are offered as a kit do not have a plans option. We do have a machine that is build form plans. The plans refer to the scratch build machine: http://www.buildyourcnc.com/cnckitintro.aspx and the one in the book "Build Your Own CNC Machine": http://www.buildyourcnc.com/Book.aspx
Click the link to add information to this solution:
Do you have a CNC machine plan available for a 4'x8' machine?
HOW LONG DOES THE TUBE LAST?
The average lifespan of a tube is 1000-1500 hours IF ran at a max of 16mA for most of it's life. It's life will go down if you run constantly at it's max rating.

CO2 laser tubes also have a shelf life. So make sure to only buy a replacement tube close to when you plan to install it, keeping it on a shelf for the future will only compromise it's life span.

To measure your amperage going through your system. You go from the negative line of the tube and run it THROUGH your multimeter/ammeter and back out to the laser PSU. This will give you your amp usage. It will not hurt your multimeter either. Just be sure your connections are very snug since 20,000V is liable to arc very easily if a connection comes loose.

Additional Information:
what is life span of CO2 generator in videojet laser coding machineVJ3320
Click the link to add information to this solution:
HOW LONG DOES THE TUBE LAST?
Does the 2X4 ft CNC model allow cutting a 2X4 ft board or what is the cutting demeninsions? Thanks
Yes, the 2'x4' CNC router (blackToe) cuts within the full 2'x4' dimensions and a tiny bit more.

Link to the machine:
https://www.buildyourcnc.com/item/cnc-machine-blacktoe-v4-2x4
Click the link to add information to this solution:
Does the 2X4 ft CNC model allow cutting a 2X4 ft board or what is the cutting demeninsions? Thanks
IS DRILL BIT USED IN THE CNC MACHINE?
The cutting tool is an end mill (it looks like a drill bit). It is a cutting tool that can plunge and cut sideways. That item is not included and is a consumable. You will purchase these very frequently and will have geometry that is very specific to how you apply the cnc machine.

Additional Information:
Click the link to add information to this solution:
IS DRILL BIT USED IN THE CNC MACHINE?
CAN I USE A MAC TO CONTROL THE CNC?
There are several CAD/CAM programs out there for MacOS. Here is a list of a few: http://www.macuser.de/forum/f53/3d-2d-cad-395058/#post4499316
I've also read good things about punchCAD: http://www.punchcad.com/
Of course, there is always SketchUp if you are in a pinch. There are a few CAM plugins for SketchUp as well, but I've never used them, so I can't vouch for them.

CAD/CAM will get you as far as designing your parts and producing the g-code, but if you also want to run the CNC machine with your Mac, you will need a piece of software similar to Mach3 or EMC to run the g-code. I haven't been able to find anything like these programs that runs on Mac, so you may have to run Mach3 or EMC in Windows using Boot Camp or a virtual machine such as VMware or Parallels.

Personally, I would use the Mac to do all the CAD/CAM, then use a cheap PC to run the CNC machine.

Additional Information:

Additional Information:
EasyDNC for OSX
www.dnc-x.com

Additional Information:

Additional Information:
Hi guys I’m new to the cnc and I’m beginning to learn how to operate and cad-cam software also my cnc runs on Mach3 my questions is if I should use MacBook to do all designs if I can have all this software to run on Mac or I have to use windows software to operate it? I have separate small computer connected to the cnc table who have Mach3 on it please help. Also if you know any other software much easy for beginners please let me know thank you guys!
My email if needed is r1jastrzebski@gmail.com

Additional Information:

Additional Information:
Hi , thank you for your advise!

Additional Information:
Hi , thank you for your advise!

Additional Information:
Hi , thank you for your advise!

Additional Information:
Hi , thank you for your advise!

Additional Information:
Click the link to add information to this solution:
CAN I USE A MAC TO CONTROL THE CNC?
Are the CNC machines covered by warranty?
Customers have 30 calendar days from the date of delivery to return the item(s) for a full refund. The returned items must not have been used or powered in any way. The item(s) must be in its original unused condition. Send the unused item(s) to: BuildYourCNC, 20734 Settlers Lake Cir N., Katy, TX 77449 and include a letter explaining the reason you need to return the item. The original shipping is non-refundable. There is a 10% restocking fee for returned items.
Click the link to add information to this solution:
Are the CNC machines covered by warranty?
CAN I USE AN APPLE COMPUTER TO RUN THE CNC?
There are several CAD/CAM programs out there for MacOS. Here is a list of a few: http://www.macuser.de/forum/f53/3d-2d-cad-395058/#post4499316
I've also read good things about punchCAD: http://www.punchcad.com/
Of course, there is always SketchUp if you are in a pinch. There are a few CAM plugins for SketchUp as well, but I've never used them, so I can't vouch for them.

CAD/CAM will get you as far as designing your parts and producing the g-code, but if you also want to run the CNC machine with your Mac, you will need a piece of software similar to Mach3 or EMC to run the g-code. I haven't been able to find anything like these programs that runs on Mac, so you may have to run Mach3 or EMC in Windows using Boot Camp or a virtual machine such as VMware or Parallels.

Personally, I would use the Mac to do all the CAD/CAM, then use a cheap PC to run the CNC machine.

Additional Information:

Additional Information:
EasyDNC for OSX
www.dnc-x.com

Additional Information:

Additional Information:
Hi guys I’m new to the cnc and I’m beginning to learn how to operate and cad-cam software also my cnc runs on Mach3 my questions is if I should use MacBook to do all designs if I can have all this software to run on Mac or I have to use windows software to operate it? I have separate small computer connected to the cnc table who have Mach3 on it please help. Also if you know any other software much easy for beginners please let me know thank you guys!
My email if needed is r1jastrzebski@gmail.com

Additional Information:

Additional Information:
Hi , thank you for your advise!

Additional Information:
Hi , thank you for your advise!

Additional Information:
Hi , thank you for your advise!

Additional Information:
Hi , thank you for your advise!

Additional Information:
Click the link to add information to this solution:
CAN I USE AN APPLE COMPUTER TO RUN THE CNC?
WHAT DOES THE GREENBULL KIT INCLUDE AND DO I NEED TO INCLUDE?
The greenBull 4X comes with all of the components and electronics to assemble the gantry of the machine. You will need to build the table. We provide the rails and roller chain for the X-axis (along the length of the table for full 8 feet of travel). You will need to provide some wire to connect the electronics and a computer to run the machine. You will also need to purchase the software that you will need to run the machine that matches how you will apply the machine. We suggest the mach3 control program. The CAM program is up to you as there are many options out there.
Click the link to add information to this solution:
WHAT DOES THE GREENBULL KIT INCLUDE AND DO I NEED TO INCLUDE?
CAN THE GREENBULL CUT 18MM BIRCH IN ONE PASS?
If you use the 2.2kW spindle, it can cut at 3/4 inch or 19 mm deep with at least a 1/4" cutting diameter single flute end mill. You will get better results with larger diameter end mills, but that is the worst case scenario. I still recommend doing a finishing pass on the edge to make sure everything is perfect.
Click the link to add information to this solution:
CAN THE GREENBULL CUT 18MM BIRCH IN ONE PASS?
WHAT THE DIFFERENCE BETWEEN 3 AXIS AND 5 CNC?
3 axis machines cannot create undercuts in the part.

These videos show the capabilities of 3 and 5 axis machining:

3-axis CNC:
&feature=fvwrel

5-axis CNC:
&feature=related

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:

Additional Information:
Click the link to add information to this solution:
WHAT THE DIFFERENCE BETWEEN 3 AXIS AND 5 CNC?