For our parallel breakout board (https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay#prettyPhoto/2/) the schematic will show the connections going from the BB to the drivers. The parallel breakout board uses the 25 pin parallel connection to communicate from the computer to drivers, and the USB is used to power the main-board itself, supplying 5V.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
I am wiring my breakout board and it has a USB port on it. Is the USB port there to supply the 5 volt power to it?

The parallel breakout board contains a USB port to power the board. Through the USB port, the computer delivers 5v of stable power to the parallel breakout board, but doe not provide any communication as would normally be associated with USB connectivity.

The reason we elected to use the USB port to provide power is to remove the need for an external 5v wall adapter.

Click the link to add information to this solution:
Does the Blue Brew breakout board require 5v to be supplied from a USB cable, to pass parallel port outputs to its terminals?

To use the inputs and outputs on the MAch3 USB controller, you will need at least a 12 VDC power supply inte 24V terminal (V+) and the DCM terminal (V-). The common lead of the limit switch will be connected to DCM (V-) and the NO (Normally Open ) lead of the limit switch will be connected to the Input of your choice (IN1 - IN4).

Click the link to add information to this solution:
[65] So do you need a 24 volt power supply on the USB breakout board or can you use the 5 volt side ?

The 5V power required for the breakout board can be a simple USB male to male cable, that will connect from your computer to the board itself.
Now adding a external power supply make sure that it does not exceed a total of 5V and the standard 500 MilliAMP - 1 A.

Click the link to add information to this solution:
I have a YDH-18-5 Power Supply AC Input:100-240v 47-63Hz, Ouput: 5v - 2A and need to know if its safe to use with the Parallel Breakout Board.

We generally use the USB to power the interface (breakout board). The current from the computer is sufficient to supply the breakout board.

Click the link to add information to this solution:
Breakout Board with Relay. What is the USB connection on this board for? Does this board Still require a 5v power supply?

Sure, connect O2 (output #2) on your mach3 USB board to the GND side of your relay coil. Connect the 24V power supply to the positive side of your 24v relay.

You will want to connect a flyback diode (1N4007) between the coil connections to make sure the coil back current does not damage the Mach3 USB board.

Refer to this diagram:
https://www.buildyourcnc.com/Documents/Electric%20Wiring%20Diagram.pdf

Please let me know if this helps and if you need further guidance.

Thanks

Click the link to add information to this solution:
I recently purchesed a USB Mach3 breakout board and need help setting mach3 to use a relay to start the router can you show how to set the pins and which port to use on the board to attached the relay?

Any of the following power supplies will be fine for powering the Mach3 USB controller:
https://www.buildyourcnc.com/item/24v

however, the limit switches do not need high current, so the following power supply is sufficient for the task of connecting limit switches:
https://www.buildyourcnc.com/item/electronicsAndMotors-power-supply-24v-1a-dc

Click the link to add information to this solution:
What power supply do you recommend for the spindle and limit switches if I buy the USB Mach3 breakout board?

The datasheet for the parallel breakout board is here:
https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay#prettyPhoto/2/

The datasheet for the USB interface is here:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-USB-Controller-Breakout#prettyPhoto/2/


Additional Information:
20

Click the link to add information to this solution:
I need wiring instructions for the breakout board you sent yesterday. It is not like the one in the videos and I don't know where to connect the 5V. No data sheet or anything.

Hi, this BBB comes with a USB port and its cable to power it up. Once connected to the computer a led in the BBB will light up to show it has power.

Additional Information:
Breakout board I have does not have USB port for the 5v power. Does the parallel port supply the 5V power?

Click the link to add information to this solution:
Hi, I need assistance, the parallel breakout board I received looks different from the one on the video, does this one need a 5V supply? If so, where do I connect the positive and where do I connect the ground? Thanks for your help.

If your computer does not have a parallel port, all you will need is a low cost PCI parallel adapter card (these can be found on amazon for $15-$20). If you plan on using a laptop (not recommended) you can try to find a PCMCIA parallel adapter, but many people have frequent issues with this setup. A more expensive solution would be to purchase a USB smooth stepper board. Unfortunately, we do not supply any of these adapters and cannot attest to their reliability.

Additional Information:
ur gay

Additional Information:

Click the link to add information to this solution:
MY COMPUTER DOES NOT HAVE A PARALLEL PORT. HOW DO I INTERFACE WITH THE BREAKOUT BOARD?

Our breakout board, does require 5v to operate the correct voltages coming in from the drivers and also coming in from your computer, now the 5V will be supplied by the USB connection, so no external power supply is needed, for either our USB/Parallel breakout board.

Click the link to add information to this solution:
Just for general knowledge. If a spindle gets i.e. 240VAC, and the drivers 36-50VDC for power, why do you need 5VDC for the Breakout Board (BlueBrew)? Is it only for the relay? I think I've seen other BoB's working without power supply, or am I wrong?

The board layout is different and the terminals have slightly different names, but the two boards function the same. The wiring diagram is the same for both boards. The plug-in driver for Mach3 is also the same, so you should not have a problem. If you do run into an issue, please let me know here and I will help you determine the problem.

Thanks

Additional Information:
Thank you for the assurance that the boards will function the same. You did not answer the primary question of wiring. The diagram shows a board with a 5V for each axis, the new boards have only 1 5V point on the axis side. In retrospect since this controller receives information and most possibly the 5V signal directly from the computer leading to the drivers. I will wire the X, Y and Z axis to the single 5V point and see what happens.

Click the link to add information to this solution:
received my mach 3 USB breakout board today. The layout of the board is different from your diagram which shows a 5V power slot for each axis. Do I wire the 5V slot with only one 5V wire from one of the drivers or perhaps wire all three 5V wires into the one 5 V slot. Please advise.

The parallel breakout board has the db25 connector for data and the USB connector for power. Connect the USB from the computer to the parallel breakout board so the breakout board will have 5V of power coming from the computer. The db25 connector (connector with the 25 pins) receive data signals for each pin from 1 to 17 and have respective numbered screw terminals, some for input and some for output (18 to 25 are gnd pins).

Click the link to add information to this solution:
Should I connect both the USB and the 25 pin connector of the parallel breakout board to the computer?

I suppose you are trying to determine how to connect the VFD tothe relay on the breakout board. This is possible, however, not recommended as there is a more robust way to connect the VFD to mach3 or mach4 that allows that CNC machine control software to control the speed and other features of the VFD.

Follow the instructions from this question (number 13383):
https://buildyourcnc.com/FAQ/13383

To get to this answer, you can also ask this customer service "How can I connect my spindle's VFD to mach3?"

Additional Information:
If you still want to connect the VFD through the relay, I will clarify this instruction on this question tomorrow as I don't have the information in front of me at this moment. Thanks.

Click the link to add information to this solution:
Need wiring diagram from mach3 USB breakout board to inverter.

The Mach3 USB board will fit in the redLeaf, but you may need to modify the Plexiglas top for proper mounting. However, the redLeaf has the proper parallel GPIO on the motherboard for use with the Parallel breakout board. If you have a laser on the machine you are using, then I would urge you to maintain the parallel breakout board as the Mach3 USB board will not work correctly using the Z-direction pin and you will need to determine how to use the output pins onthe USB board to ensure proper laser functionality.

Click the link to add information to this solution:
Will Mach3 USB Interface board fit in my redleaf, in lieu of the breakout board that came with it?

The use of the hex inverter in the application to invert a direction signal to have a motor run in the reverse directions is relatively simple.

First, go to this link and look at the chip diagram:
https://www.buildyourcnc.com/item/electronicsAndMotors-hex-inverter-breakout-newbiehack-integrated_circuits-hex-inverter

Connect 5V from the USB interface tothe VCC pin. The pin on the keyboard jog header can be used. Connect the GND pin from the USB interface to the GND pin on the hex inverter. Connect the CW terminal from the USB interface to the 1A pin on the hex inverter. Connect the 1Y pin from the hex inverter to the driver.

Additional Information:
I got a question??? I am a dummy when it comes to cnc. I got 6040 1500kw water cold engraver 3 axis from china. I can not get anything out of them pertaining help they keep telling me the same thing over and over and over and I'm doing it and send them pictures that I know. Anyway email me a wiring diagram for the PRT 1500 watt spindle motor control box and has the emergency stop on and off switch manual PC and of course yhe screanm fultonsbusiness@gmail.com

Additional Information:
I got a question??? I am a dummy when it comes to cnc. I got 6040 1500kw water cold engraver 3 axis from china. I can not get anything out of them pertaining help they keep telling me the same thing over and over and over and I'm doing it and send them pictures that I know. Anyway email me a wiring diagram for the PRT 1500 watt spindle motor control box and has the emergency stop on and off switch manual PC and of course yhe screanm fultonsbusiness@gmail.com

Click the link to add information to this solution:
Is there a wiring diagram for hooking up your hex inverter between your USB breakout board and the controller?

No, you should not have received two parallel breakout boards in your CNC kit. You can return the extra item using standard shipping with COD. Our apologies for the confusion and the inconvenience.

I will answer the other question as another FAQ. Please check the Customer Service page to see the answer to that question.

If you have difficulty finding the answer, here is a link:
https://www.buildyourcnc.com/FAQ/13636

Click the link to add information to this solution:
I HAVE A 2000 WK 11–3 Z LIMIT SWITCHES GOING TO C10R10 BREAKOUT BOARD . CAN ALSO USE THEM AS MY HOME POSITION WELL. NEED THE WIRING CONFIGURATION

If you are using a spindle with a VFD, there is a 24 volt power supply that will provide the correct power for the V+ and V- on the Mach3 USB. The 12V option is only if you are using the limit switches on that side of the board, but if you are using it to control spindle speed and for the outputs, it's best to use a 24V power supply, or the 24V output on the VFD.

Additional Information:
Closed loop

Additional Information:
Can i use 12v in the 24v input

Click the link to add information to this solution:
The Mach 3 usb board requires an additional 12V power supply. How many amps would you recommend? Would a 1A wall adapter suffice.

You will need PlanetCNC software for the USB breakout board and when plugging in the USB the computer should automatically recognize the board, however you can go into device manager to see if the USB terminal is working correctly.
The parallel breakout board; the USB is not a connection terminal rather than a power source, and the parallel port will be the communication terminal.
The items you will need for a water cooled spindle would be: water pump, silicon tubing(length desired by customer), a extension cord(from a hardware store(orange))(1 same gauge wire/length as extension cord).

Click the link to add information to this solution:
I have the usb breakout board https://buildyourcnc.com/Item/electronicsAndMotors-electronic-component-USB-Controller-Breakout and need to run the A axis as a slave the software greys out the box how do I fix this?