To stop the laser completely from continuous firing after a job is complete, I recommend to have your file to end while reaching the clearance plane which you will enter in your CAM software. Make sure that your clearance plane value is very small (ex.) 0.001 above 0 and activates at -0.001 also adding a additional g-code manually that raises the z-axis towards the end of the job/run(only if experienced would we recommend using this). This will turn of the laser, rather than the laser staying on and at its current height.

When activating the emergency e-stop, (personal opinion) I would wire the e-stop at the beginning of the live/load wire going to the electronics power supply and the laser power supply.
It will be in at the beginning of the y connection, (https://buildyourcnc.com/blackToothLaserCutterAndEngraver.aspx#prettyPhoto/13/) so you will cut power to both instead of just the CNC electronics.

Click the link to add information to this solution:
Need help configuring Planet CNC software to control laser firing. Currently it is firing using the Z axis but leaves the laser on after a run or when the emergency stop is activated. HELP!!

Software specific questions for Planet-CNC will have to come from them or other sources as we are not fully equipped to troubleshoot all issues. If the issue is related to motor tuning or setup involving our electronics, then we will gladly assist you. You may contact techsupport@buildyourcnc.com with inquiries.

Click the link to add information to this solution:
What do I need to purchase from you to get me running. I have planet cnc control board but it is difficult contacting them when I need help.

The Planet CNC Software will require purchase after the trial version is completed, and will be purchased through their website. Currently that is the only software available for the USB Controller.

Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
I have rhino software, I am going to purhase planet cnc software. Would I need any more.

The Planet CNC Software will require purchase after the trial version is completed, and will be purchased through their website. Currently that is the only software available for the USB Controller.

Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
I have rhino software, I am going to purhase planet cnc software. Would I need any more.

Mach 3 is compatible with our electronic combo's that include the Parallel Breakout Board.
Planet-CNC is compatible with our electronic combo's that included our USB Breakout Board.

The parallel breakout board is compatible to a wide variety of software control packages. The USB interface board that we sell can only be used with the Planet-cnc control software.

If you are concerned with your computer (desktop) not having a parallel port, one can be purchased and inserted into a PCI slot on the motherboard. Some motherboard also come with a parallel port header (connector) on the motherboard and a simple cable can be connected to this connector to get that functionality on the computer. The former solution of getting a parallel port adapter card to plug into the motherboard is probable the easiest and least expensive option.

Additional Information:


Additional Information:
Is the mach 3 software compatible with kollmorgen s200 servo motors and controllers?

Click the link to add information to this solution:
IS THE MACH3 SOFTWARE COMPATIBLE WITH 3 AXIS MOTION CONTROL COMBO KITS? PLANET CNC MENTIONED AS BEING COMPATIBLE.

Is the signal gnd on the laser power supply connected to a gnd on the breakout board? Do you hear a high pitched sound, like a TV set with an antenna getting interference, but with a high pitch?

Click the link to add information to this solution:
OUR FIRST ATTEMPTS WERE WITH THE PLANET-CNC SOFTWARE, GOING THROUGH USB BOB. NO PROBLEM GETTING X & Y AXIS TO MOVE BUT UNABLE GET ANY ACTIVITY ON Z AXIS. WE THEN INSTALLED MANUAL SWITCH BETWEEN 5V AND TL, JOY. DISCONNECTED BOB FROM TH, MOVED OVER TH TL STILL

Mach 3 is compatible with our electronic combo's that include the Parallel Breakout Board.
Planet-CNC is compatible with our electronic combo's that included our USB Breakout Board.

The parallel breakout board is compatible to a wide variety of software control packages. The USB interface board that we sell can only be used with the Planet-cnc control software.

If you are concerned with your computer (desktop) not having a parallel port, one can be purchased and inserted into a PCI slot on the motherboard. Some motherboard also come with a parallel port header (connector) on the motherboard and a simple cable can be connected to this connector to get that functionality on the computer. The former solution of getting a parallel port adapter card to plug into the motherboard is probable the easiest and least expensive option.

Additional Information:


Additional Information:
Is the mach 3 software compatible with kollmorgen s200 servo motors and controllers?

Click the link to add information to this solution:
Is the Mach3 software compatible with 3 axis motion control combo kits? The planet cnc software is mentioned as being compatible.

You can download a trial version of PlanetCNC software from their site at http://www.planet-cnc.com/index.php?page=software to see how you like the interface. If you look at their main GUI screen, along the left side you will see 4 boxes labeled X,Y,Z and A. These represent the axes the software is equipped to control. (A being Axial, or rotational motion) Typically a separate motor and driver is used to control each axis. If you plan to switch axes you will need to connect and disconnect the outputs from your software to the drivers.

Click the link to add information to this solution:
sorry, this is what i meant to say: OK, so if I use the USB version then I would find the rotary/linear axis definitions in the planet cnc control software somewhere. I will be needing to change axis type often for various projects that is why I am asking.

For our redFly there is no need for firmware, however you will need to purchase a license for the board. Which you can buy here: (http://planet-cnc.com/product/cnc-usb-controller-license/)
The license is to completely unlock the software Planet-CNC.

Click the link to add information to this solution:
i have a redfly box for a greenbull 5x10 do I need to load a firmware to use planet cnc or is it already done

The diagram for wiring the USB interface board is located here: https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-USB-Controller-Breakout#prettyPhoto/2/

Under the board illustration, there are three smaller diagrams of limit switch wiring. On each, there are two connections, the GND and the pin which are labeled at the ends of the circuit on the diagrams. The pin side would go to the axis label ++ or -- terminal (i.e. X++, or X--). The other end, labeled GND would connect to any ground terminal on the board.

Click the link to add information to this solution:
I am using 5 limit switches on my 3 axis machine. I am using the usb controller for planet cnc. I would like to know where all the wires related to the limit switches get connected? A diagram would be helpful.

You will need a USB cable to connect the computer and the Mach3 USB. The 64-bit operating system must be Windows and you will need the Mach3 CNC control software installed on the operating system.

You will need to install the USB driver called RNRMotion.dll. You can find the driver here: https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Move the file to your Mach3 Plugins folder Example: "C:/Users/ProgramFiles/Mach3/Plugins"

Mach3 will prompt you to select a driver and this is where you can select the "RnRMotionController" and check "Don't ask me again". This will allow your board to communicate with Mach3.

You will also need the xml file found on this page: https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

On that page, you will need to download the XML Mach3 Config File by right clicking on the link and selecting "save as". Save the Mach3Mill.xml file in your Mach3 root folder.

That file is the main configuration file for the Mach3 board. It has all of the typical settings that the Mach3 board needs.

Click the link to add information to this solution:
I have a 64 bit operating system and the Mach3 usb control board. What do i need to communicate between the two?

On the Planet-CNC board, the Mist, Spindle and Coolant outputs will require a relay to switch on those devices. Test one of those terminals with a multi-meter (Mist, Coolant, or Spindle). Each of these terminals have a GND next to the terminal for the device.

Test the voltage across the GND to the terminal with the arrow that you want to test. Go to the software and click on the device you want to test (mist, coolant or spindle) and note the voltage. If no voltage is output then check under the board to where the terminals are soldered. Re-test the terminals across the solder joints rather than the terminal block wire inputs. If you get a voltage, then there is a problem with the terminal block. If you don't get a voltage, then the board is not functioning properly.

Additional Information:
I activated the output signal.. I did the tests indicated and I did not get voltage. I heated the welds of the three outputs and now works coolant but no mist or spindle, what should I do?

Additional Information:
There are probably cold joints on the board at the chip or the resistors on the traces for those terminals. You can send the board back to us and we will repair and test the board.

Click the link to add information to this solution:
I have a "Based on planet-cnc's diy cnc usb controller", I activated the output signal (mist, coolant or spindle) in the planetcnc software but at the output there is no voltage, what can I do to turn on this elements?

On the Planet-CNC board, the Mist, Spindle and Coolant outputs will require a relay to switch on those devices. Test one of those terminals with a multi-meter (Mist, Coolant, or Spindle). Each of these terminals have a GND next to the terminal for the device.

Test the voltage across the GND to the terminal with the arrow that you want to test. Go to the software and click on the device you want to test (mist, coolant or spindle) and note the voltage. If no voltage is output then check under the board to where the terminals are soldered. Re-test the terminals across the solder joints rather than the terminal block wire inputs. If you get a voltage, then there is a problem with the terminal block. If you don't get a voltage, then the board is not functioning properly.

Additional Information:
I activated the output signal.. I did the tests indicated and I did not get voltage. I heated the welds of the three outputs and now works coolant but no mist or spindle, what should I do?

Additional Information:
There are probably cold joints on the board at the chip or the resistors on the traces for those terminals. You can send the board back to us and we will repair and test the board.

Additional Information:
If you want to troubleshoot this yourself, take a very close look at the traces from the terminal and follow them to the tiny resistors, then to the legs of the chip. If you see any bad or bridged solder joints, then those will need to be re-touched. It will take a somewhat experienced soldering individual to accomplish this task and will require flux to make sure the solder joints are fully joined.

Click the link to add information to this solution:
I have a "Based on planet-cnc's diy cnc usb controller", I activated the output signal (mist, coolant or spindle) in the planetcnc software but at the output there is no voltage, what can I do to turn on this elements?

If you select the Settings Page and select or tick Auto Limit Override - this will allow you to back off the switch.

Additional Information:
limit and home switch

Click the link to add information to this solution:
When the machine hits the limits it stops but the switch is still tripped so clicking the Mach3 RESET button doesn't do anything. How am I supposed to get the machine to move off of the limit switch so I can continue working?

The driver and motor need a pulse train signal from the computer to move the motors, so it would be best to at least install the control software and use the jog feature to test the motors.

Click the link to add information to this solution:
Do I need to install cad\cam,and control software to test x,y,and z hardware when it is completely installed?

Could you specify which breakout board you have? If you have a parallel port version, be sure that you have purchased the "legacy" parallel port version from Mach4. If this proves not to be the problem, please feel free to email us directly at techsuport@buildyourcnc.com or call 281-815-7701 for troubleshooting instructions.

Click the link to add information to this solution:
I need a resource, we bought 2 redfly systems and mach 4, We put one motor on for the x axis but cannot get it move. Can you direct us to some tutorial?

Surely you know the brand motors you sold me?

Click the link to add information to this solution:
I bought your 3 axis combo and need to know what name brand is the motors and their ounces and the drivers

Depending on the size of your CNC machine, it will vary the length required for your application.
Please verify the CNC machine, and we can go into detail on the specific lengths or methods for the linear guide mechanics.

We sell our ACME Screw (1/2" per inch), also our longest length of ACME Screw is 76-3/4".

Click the link to add information to this solution:
Hi, I need the lead screw and bearings for x/y/z axis of the CNC. What is the length of "1/2" Lead Screw per inch (Steel)"?

The instructions on how to use a plate for z-axis homing (moveable sensor) can be found here:

http://www.planet-cnc.com/faq/moveable_sensor/

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
Using your USB control board, is it possible to install and use a Z axis touch plate? If yes, what board connections would it be installed to?