No, the 3.1 version will not support slaving the X axis. You will either need to wire the two x axis driver to the same X signal pins, or use the DDCS v4.1 which does support slaving an axis.

Click the link to add information to this solution:
[823] I plan to use a DDCS stand alone controller for a CNC router build which will have two stepper motors on the x axis, one on Y and one on Z. Will the 3.1 version handle two motors synched on the X axis or will I need the 4.1 version?

The 5x10 greenBull base kit comes with the structure, hardware, and electronics for motion control. In order to have a fully functional CNC you will need a table base for your machine, a spindle or router to handle your cutting applications, end mills (bits) for cutting, CAD, CAM and CNC software, and a computer. There are also accessories you can add such as limit switches, emergency stops, and cable carrier for cable management. If you are looking for more information or a formal quote please contact sales@buildyoucnc.com

Click the link to add information to this solution:
I'm not sure of ALL the things I will need to do some of my ideas for the cnc machine. I'll mostly be cutting out 3/4" plywood projects. How much minimum for a 5' by 10' system? I need the hardware and software to get the job done. I saw the price for your basic unit 3-4 grand but don't know what all I NEED to start work.

I would not recommend slaving an axis using the method of taking an additional axis from the USB interface. Instead, wire both drivers to a single axis on the USB interface. This will insure perfect signal output to both drivers. If you requre the motors to spin in opposite directions, simply wire one of the motors to the driver reversing the coil A and B connections, or use a hex inverter (https://www.buildyourcnc.com/tutorials/Tutorial-Two-Motors-Spinning-Oppositely-On-Single-Axis).

Click the link to add information to this solution:
I purchased a USB Breakout board, motors and drivers, paid for CNC USB Controller Software and I CAN NOT "Slave" an axis, but there is an option to do that. The moment I connect USB Breakout Board "Slave" option becomes shaded and I can no longer select it (becomes not functional). What is going on? Need help asap. Thanks

The blackToe 2'x4' cnc machine is sold as a kit only. We offer plans for the scratch (book) build machine that can be found here for purchase and also comes with a DVD showing the build process: http://www.buildyourcnc.com/cnckitintro.aspx and the plans for build in the book is on the CNC book page: http://www.buildyourcnc.com/Book.aspx.

You can use the same size stepping motors referenced in the book: http://www.buildyourcnc.com/category/elcombo

Click the link to add information to this solution:
I would like to build the 2’x 4’ blackToe2x4v40 CNC router. I have your book. I want to build the latest model blackToe2x4 v40. Are those the correct plans on your web book page ? Is there a bill of materials? If I use a Porter Cable 3-3/4 router motor what size stepper motors do I need?

The motor is helped by the mechanical leverage of the screw. The 425 oz-in motors that are included in the standard electronics combo has very high torque for that type of machine. You will have no problem using that motor for the book machine.

We use that motor for very heavy spindles on the blackToe and blackFoot CNC Machine kits.

You will need to do the mechanical leverage calculation along with the torque of the motor to determine the actual weight it will lift. The calculation will need to consider the type and pitch of the screw and it would also consider the gravity constant of 9.8 m/s/s.

If you need me to determine this formula and work out the calculation based on the screw you are using, please let me know.

Additional Information:
thank you for the reply. I would be really good to know the calculation. The lead screw is 1/2" diameter with 13 TPI. Please provide the calculation. And one more question. If I am cutting 18mm MDF with 6mm cutting bit (so 6mm pass), what can be the maximum speed rate of cutting and spindle speed of router?
thank you

Click the link to add information to this solution:
I received the electronics for book build cnc machine. I need to know how much weight the z-axis motor can hold since my (craftsman) router seems to be heavy. It is 2HP with variable speed

You should have no problem connecting the Pokeys57CNC controller to the drivers of your machine as long as the drivers have step (Pulse or PUL) and direction (DIR) terminals. You will need the cable pack that is sold separately so you can connect the headers/connectors of the pokeys57cnc controller to the drivers using ribbon cables.

I show this process in great detail on this page:
https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Is you scroll down on the page, you will see a set of videos that show the process step-by-step.

Click the link to add information to this solution:
I have a ShopBot CNC that was converted to Mach 3. The controller has gone out. I pourchased your Pokeys57 board, but I'm not sure I have everything I need. I think my motor drivers are OK, but am not sure how to wire them to what I purchased from you. Need Help. How can we make this work, or do I need a different board to distribute the movement signals to my drivers?

We recommend our electronics combo for the scratch build kit, which you can find on our site here: https://buildyourcnc.com/item/electronicsAndMotors-3axis-425-elcombo. This is our standard general purpose 3 axis electronics system, and includes (3) NEMA 24 425 oz-in stepping motors, (3) Drivers (3.0Amp 24-40 Volts, with 1-1/64 microstepping), (1) 36v 8.8a Power Supply, (1) Interface Board either USB or Parallel. (The USB version requires PlanetCNC software; the parallel interface board gives you a variety of options, Mach3 being one popular choice.)

Click the link to add information to this solution:
I got the plans and hardware from you guys and im almost ready for the stepper motor part of this build. what size motors are good to use for this build? the size of cnc will be 2x4 when finish or what size will not work? thanks

The settings that will have to be change will be your steps per inch in motor tuning (mach 3), or settings/axes(planetCNC). But we do not have the actual numbers/specs that will fit your 10 TPI 5 start lead screw, here is a tutorial video which explains how to get the exact numbers you need! (

Click the link to add information to this solution:
On the Book Build: I'm changing the 13TPI 1/2" lead screw with the 1/2" 10 TPI Acme screw with the anti backlash nut. This is for the Z axis only. What should I know about installing it and what are the numbers I need to plug into the motor tuning area.

If your motors turn very slowly using your Mach3 USB board, then either the pulse from the board is being output at a slow rate or the motor drivers are set to a higher than expected microstepping:

The Mach3 USB board outputs the pulse rather than the computer, but Mach3 controls this pulse frequency within the motor tuning section. First, determine if the travel distance is correct with the computer and the physical travel of the machine.

If the travel is different, then your stepper motor driver's microstepping is incorrect, or the steps per inch/mm in the motor tuning within Mach3 is incorrect.

If the travel is correct, then simply change the velocity and acceleration parameters to your desired level. If Mach3 will not achieve the velocity you desire, then decrease your stepper motor driver's microstepping setting, readjust the step per inch/mm in mach3 and readjust the acceleration and velocity to your desired levels.

Additional Information:
Text is engraved in mirror image

Click the link to add information to this solution:
I have not used my CNC router (Mach3, USB interface board) for several months. When I tried to use it, all 3 stepper motors moved extremely slowly. Where should I start troubleshooting?

You will need to build the table unit for your machine. There are instructions on how to do this at the bottom of the product page here, https://www.buildyourcnc.com/Item/cnc-machine-blackFoot-v4
There is no estimate on how much this will cost though, since there are too many variables involved to do this.

- PC with parallel port and USB port
- 20awg stranded wires for the motors - http://www.buildyourcnc.com/electronicscombo.aspx
- 18awg stranded wires for power supply to drivers
- 24awg stranded wires for breakout board to drivers
(location and spacing of components varies from one person to another, so we do not provide cables/wires)
- General purpose extension cord (cut the female end off) to provide power to power supply
- USB cable to power breakout board
- Parallel cable to communicate to breakout board
- Router
- (optional - instead of router) Spindle with power inverter http://www.buildyourcnc.com/SpindlesAndAccessories.aspx
- (if purchasing spindle with inverter) General purpose extension cord (240v) (cut the female end off) to provide power to power inverter
- End Mill(s) http://www.buildyourcnc.com/ProductsEndMills.aspx
- CAD, and/or CAD-CAM software (to produce geometry, machine operations, and g-code) http://www.buildyourcnc.com/CNCsoftware.aspx
- CNC control software (to read g-code and control machine) http://www.buildyourcnc.com/CNCsoftware.aspx

This answer is applicable to most of our machines with the exception of the greenLean and the blueChick since those machines are equipped with a table structure.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
I just wanted to know what I can expect to pay to build the blackFoot 4'x8' CNC machine, excluding computer, software and router? Is the kit complete or do I have to purchase additional items to finish?

Dealing with our USB BoB, the potentiometer that will be used in the key jog, is a 5V, 5k - 10k Ohm potentiometer.

Click the link to add information to this solution:
I am building a cnc mill using your USB controller and i would like to know what is the specification of potentiometer used for adjusting manual axis jog speed

Polabs prepared step by step user guide for PoKeys57CNC and Mach4 to try answering such questions. It is available in our downloads section: https://www.poscope.com/wp-content/uploads/downloads/Pokeys/LibrariesAndPlugins/Mach4 and PoKeys57CNC - step by step guide.pdf

Click the link to add information to this solution:
What is the 24VDC Power requirement for the Pokeys47CNC? 1A, 2A? ...I'm running a separate 36VDC PS to the Stepper drivers and a 24VDC PS to the Controller.

Hola puedo venderte una maquina nueva completa chocofrutfc@yahoo.es

Click the link to add information to this solution:
Hi, I’m purchasing an ox build workbee cnc router from China but I need to purchase the spindle mount, router and all cables/wires. Please can you give a list and quote of what I will need? I am purchasing the electrical pack with it but it doesn’t come with the cables and all other bits I need. Thank tou

We apologize for the confusion, however in the very first video that is regarding the assembly, is of the torsion box. We do not included that in any greenBull kit, as we use too sell it individually! However due to high consumption of materials and high cost(both in shipping and for the kit itself) we have removed it from our inventory and no longer sell it.

This video can be skipped, however if you plan on making a DIY torsion box, this video will be helpful in your build!

The torsion box is not needed, as the frame itself will be more than sufficient in keeping the machine from flexing or vibrating.

Click the link to add information to this solution:
I ordered the GreenBull 5' x 10' kit. The first video for assembly shows that I should have 5 large boards that attach to the table, but I don't have those boards. Is that something I need to build or were they not shipped?

We recommend our electronics combo for the scratch build kit, which you can find on our site here: https://buildyourcnc.com/item/electronicsAndMotors-3axis-425-elcombo. This is our standard general purpose 3 axis electronics system, and includes (3) NEMA 24 425 oz-in stepping motors, (3) Drivers (3.0Amp 24-40 Volts, with 1-1/64 microstepping), (1) 36v 8.8a Power Supply, (1) Interface Board either USB or Parallel. (The USB version requires PlanetCNC software; the parallel interface board gives you a variety of options, Mach3 being one popular choice.)

Click the link to add information to this solution:
I am going to build a CNC 4x4 plasma table. The frame is made of 1 1/4" pipe and the gantry will be made of either 2"x 2" or 2"x 3" tubing. What size stepper motors do you suggest?

Have you considered reversing the A and B coils on one of the motors to the drivers? This will cause the motor to spin in the opposite direction. This is the easiest method. Using the HEX inverter is a more complex method and not recommended for simple driving tasks.

Click the link to add information to this solution:
I have two nema 34 motors on my gantry and ordered a hex inverter, now I need to wire it correctly. What type of wiring hardware do I need and I will need a wiring diagram also. Please help.

Have you considered reversing the A and B coils on one of the motors to the drivers? This will cause the motor to spin in the opposite direction. This is the easiest method. Using the HEX inverter is a more complex method and not recommended for simple driving tasks.

Click the link to add information to this solution:
I have two nema 34 motors on my gantry and ordered a hex inverter, now I need to wire it correctly. What type of wiring hardware do I need and I will need a wiring diagram also. Please help.

Did you install the Mach3 USB plug-in?

Make sure that you followed all of the steps and diagrams on the following page:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Click the link to add information to this solution:
ABSOLUTELY NOTHING WORKS. I HAVE ALL STRUCTURE AND MECHICAL PARTS OF THE BLACKTOOTH CUTTER DONE. HOWEVER WHEN WIRE UP STEPPER MOTOR TO DRIVER. THAT MACH 3 USB CONTROLLER BOARD, TRY JOG MOTOR, WORKS! PREVIOSULY HAD PLANET CNC BREAKOUT HOWRVER, ONLY MOVED MOTORS IN ONE DIRECTION COULDNT CHANGE IT. ANY HELP WOULD BE APRECIATED

What we intend our customers to use for wiring the motors to the drivers will be 4 conductor 20 AWG cable, now for the PSU to Drivers; 16-18 Gauge wire should be used, and drivers to BB(Breakout Board) should be a 24 AWG wires.

Click the link to add information to this solution:
In my 4'x8' Blackfoot rig, there is a maximum wire length of 16" between drivers, breakout board, and power supply as well as a maximum wire length of 10' from drivers to motors. What AWG wires should I use to connect power supply to drivers, drivers to motors, and drivers to breakout board?