I would not recommend slaving an axis using the method of taking an additional axis from the USB interface. Instead, wire both drivers to a single axis on the USB interface. This will insure perfect signal output to both drivers. If you requre the motors to spin in opposite directions, simply wire one of the motors to the driver reversing the coil A and B connections, or use a hex inverter (https://www.buildyourcnc.com/tutorials/Tutorial-Two-Motors-Spinning-Oppositely-On-Single-Axis).

Click the link to add information to this solution:
I purchased a USB Breakout board, motors and drivers, paid for CNC USB Controller Software and I CAN NOT "Slave" an axis, but there is an option to do that. The moment I connect USB Breakout Board "Slave" option becomes shaded and I can no longer select it (becomes not functional). What is going on? Need help asap. Thanks

No, you do not need another motion controller if you have the parallel breakout board and you are using the "Legacy Parallel Port Plug-In" with Mach4. The motion controller is the parallel port.

Click the link to add information to this solution:
I purchased hardware for my plasma table which included 3 nema 34 stepper motors and drivers, power supply,Blue brew BOB, and Mach 4 Control software with parallel port plug-in. In configuring the Mach 4 software it asks for a motion controler. Do I need another device such as a smoothstepper motion controler?

When you plug the USB controller into the computer using a USB cable, and the planet-cnc software is running, you will be presented with a dialog box that will contain a text box for the key that you received from the planet-cnc folks.

Additional Information:


Additional Information:
Is there any other software that will work with your controller Mach3? Thanks for the help!

Click the link to add information to this solution:
However it how do I get the software to work? PlanetCNC sent me a key that looks like it will only work with a backup control board I purchased from them?

Yes, we can help you with leveling your CNC machine even if you didn't purchase it from us.

Click the link to add information to this solution:
[789] I need to level my cnc machine, but I didn't purchase it from you, so: Do you offer tech support with leveling a cnc? Because I don't see this problem listed .And: Do you offer support if my machine was purchased in China or from another vendor?

You should have no problem connecting the Pokeys57CNC controller to the drivers of your machine as long as the drivers have step (Pulse or PUL) and direction (DIR) terminals. You will need the cable pack that is sold separately so you can connect the headers/connectors of the pokeys57cnc controller to the drivers using ribbon cables.

I show this process in great detail on this page:
https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Is you scroll down on the page, you will see a set of videos that show the process step-by-step.

Click the link to add information to this solution:
I have a ShopBot CNC that was converted to Mach 3. The controller has gone out. I pourchased your Pokeys57 board, but I'm not sure I have everything I need. I think my motor drivers are OK, but am not sure how to wire them to what I purchased from you. Need Help. How can we make this work, or do I need a different board to distribute the movement signals to my drivers?

Attaching two motors in parallel is possible, but you will need another motor and driver for the opposite side. Each motor must have its own driver to work accordingly and fluently. The two can be wired together, to the same pins on your breakout board and set the dip switches on the driver to match the ones on your x-axis(ex). But remember to view the orientation of the motor and which way it spins, since it is on the opposite side it will have to be orientated correctly to move in sync with the other motor.

Click the link to add information to this solution:
I just finished building my first CNC with the electronics I purchased from you and I am already thinking about improving it. I would like to build a 2 motor X axis solution. Is it possible to attach 2 parallel motors and drivers to the BlueBrew Breakout Board? If so, how?

The best place to find information and step by step instructions for Mach4 is to use the manuals provided by MachSupport.com.

Here is a link to the PDF manuals for Mach4: http://www.machsupport.com/help-learning/product-manuals/

Click the link to add information to this solution:
I purchased Mach 4 control software and am in need of a very elementary tutorial on set up. I am extremely new to this and need step by step help. Thanks

You can do raster and vector engraving on the greenBull laser/spindle combination. The methods of this process is not accomplished in the same way as the typical laser machines where CorelDRAW is used. The Mach3 laser plug-in can be used for the raster engraving and standard CNC g-code can be used for vector cutting and engraving.

The raster method will not be fast on the greenBull since the z-axis is heavy and there are inertial limitation on doing fast raster back and forth movement. Vector is the best use of this machine.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
I am looking at purchasing the greenbull 5X system with the laser/spindle combination. Can the laser do both rastered engraving as well as vectored cutting with the same breakout board and software? If I have this wrong please let me know what would be needed to accompish this.

Software specific questions for Planet-CNC will have to come from them or other sources as we are not fully equipped to troubleshoot all issues. If the issue is related to motor tuning or setup involving our electronics, then we will gladly assist you. You may contact techsupport@buildyourcnc.com with inquiries.

Click the link to add information to this solution:
What do I need to purchase from you to get me running. I have planet cnc control board but it is difficult contacting them when I need help.

Sure, the USB interface has a place for 4 axes of limit switches.

Each axis can have two limit switches: one for the ++ (positive) end and one for the -- (negative) end. The positive end would be the limit switch at the end of the machine that, say the machine has a 4'x8' area, reaches a bit after the 8 foot mark. The negative end would be the limit switch behind the 0 foot location behind the origin. If the origin is in the middle, the negative would be at a little more than the -4 foot end and the positive would be at a bit more than the +4 foot end. Note that you can have more than one switch on each pin where the NC is connected in serial fashion and the NO is connected in parallel fashion (this can be seen on the diagram in the multiple limits switch section). The software configurations for the limits switches are under File -> Settings -> Limit.

A typical limit switch has three connections on it. These connections consist of COM (common), NC (normally closed) and NO (normally open). The COM would generally go to GND and the NC or the NO would go to the pin. If the NC is used, then the the switch is constantly connected until the switch is pushed (engaged) then the connection from the pin to gnd is broken (open). Use the settings in software to set whether in NC or NO configuration.

Let me know if this information was helpful (or not) by adding information to this question. Thanks.

User response:
Thank you very much for this helpful information. I'm still a little fuzzy on how the 6 limit switches physically connect to each other and to the USB breakout board. You've stated one switch (home) goes to positive and another switch (limit) goes to negative. Are all the GND prongs from all 6 switches connected to each other and going to GND on the breakout board, or no? And the NC prongs, how exactly are they connected to each other? And to the board? There has to be a diagram somewhere shows this visually, no? I don't know how to wire the switches in series or in parallel. I have already physically installed all the switches on the machine and ran the wires to where the board is. Now I just need to know where to plug these wires into the board. Also, taking into consideration that I'm using the Planet CNC software, the only settings I have pertaining to limit switches is "Enable/Disable" for each axis, and the actual limit for each axis. Nothing about NC or NO. Is that only in Mach3?
Thank you.

buildyourcnc response:
On the USB interface, the COM on the switch connects to GND and the NC or NO connects to the input pin (i.e. x++, y--, etc.)

Limit switch configuration is rather difficult to understand, especially with series and parallel. You can think of series as a single wire going from GND to the axis letter input terminal (i.e. X++ or X--). If the wire is broken, then the circuit is open (or the switch is engaged in a normally closed scenario). Normally closed is like an actual wire, and when engaged, the switch "opens" (breaks the wire). This is why we recommend in some systems that you can put many switches in series on a single pin. When one of the switches is engaged (breaking the connection) then the entire circuit of switches is broken and the machine stops.

In a parallel scenario, the state of the circuit is always broken until the one of the switches is engaged and the circuit is then closed or connected. The topology looks like a ladder. All the switches connect to both sides of the ladder and the switches are like the runs of the ladder (the horizontal bars that the feet are placed while climbing). Imagine all of the switches broken in this scenario (normally open). It would be like the ladder could be split in two, but if one of the ladder runs (switches) is closed by engaging it, then that run would connect both sides of the ladder and the two sides of the ladder would have a connection.

There is a diagram on the USB page of the various limit switch configurations. If you need more information (visual and/or otherwise), please let us know and we will immediately add that information to benefit everyone.

Click the link to add information to this solution:
I purchased limit switches from you mounted them on my machine and wire them to the breakout for using pin 12 and the ground on the breakout board, after a few minutes I got a message about a limit switch trip. Am I supposed to use the extra outport on the board instead of the ground?

We could not guarantee, nor say, whether or not your current software would be able to utilize the USB breakout board. Our USB breakout board is designed for use with Planet CNC software found here, http://www.planet-cnc.com/index.php?page=software

As far as we know, this is the only CNC Controller software that operates on a USB breakout controller.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
I want to change my old DSP controller and break out board with new one in your site that support usb it is possible ? if yes can we contact us to talking about details ?

To home the z-axis using a plate:
- Connect the end mill using a large clamping device like an alligator clip with a wire connected to GND.

- Connect the plate (solder a wire to the plate) to one of the input pins.

- You can use the autoset to setup that pin in Mach3 simply by touching the two together once connected to the pin and GND.

Alternatively, the end mill can be connected to the pin and the plate connected to GND as long as there becomes a complete circuit when the end mill touches the plate.

To setup homing for the Planet-CNC homing and limits, go to the Planet-CNC Machine setup page which explains the process step by step: http://www.planet-cnc.com/faq/machine_setup/

Customer Response:
How do I get homing on z to work with planet cnc software using build your own usb board. I have gone to planet website and followed the instructions provided but my software will not allow entries in the required fields they are grayed out is it because I am not using planet-cnc's board, I have used this method for years with Mach3 and would like to use it with the usb board and software.

Answer:
Just received information from the developer. The instructions on how to use a plate for z-axis homing (moveable sensor) can be found here:

http://www.planet-cnc.com/faq/moveable_sensor/

Click the link to add information to this solution:
How do I get Homing on Z to work with Plate and Ground using Buildyourcnc usb board all the entries for the sensor in planet-cnc are grayed out. I am using input z- and I purchased the software

We are working on a keypad that will connect to the USB interface. It is possible to create a quick keypad using perf-board and some push buttons. All you need to do is connect one side of the switch to the pin of the axis and direction and the other side of the push button to the 5v pin. The datasheet shows the pinout of the jog connector.

Additional Information:
I had found the pins to wire in a job connector. My question is, what sort of connector do I look for (on Amazon for example) that will work for each 2 pin pair? I suspect they are the same as the connector for power and reset on my computer's motherboard, but I have no idea what to look for (what to buy).
thanks.

Additional Information:
20

Click the link to add information to this solution:
I need to find a connector(s) to wire a pushbutton array to the USB board I purchased. Do you sell such a connector. Can you tell me what to look for?/What such a connector is called?

Identify the Control Signals: First, determine which control signals from the DB25 interface card are used for spindle speed control. Typically, these are PWM (Pulse Width Modulation) signals or analog voltage signals.

VFD Configuration: Your VFD should be configured to accept the type of control signal your DB25 card provides. This involves setting parameters in the VFD that correspond to the type of input signal it will receive for speed control.

Wiring: Connect the appropriate output pins from the DB25 card to the input terminals on the VFD. This usually involves connecting the PWM or analog output to the corresponding input on the VFD. Make sure to consult the manuals for both your VFD and interface card for specific wiring details.

UCCNC Settings: Configure UCCNC to output the correct type of signal (PWM or analog) that matches your VFD's configuration. This is done through the software's spindle setup section.

Test and Adjust: Run some tests to ensure that the spindle speed is being correctly controlled by UCCNC. You might need to tweak settings in either the VFD or UCCNC for optimal performance.

Click the link to add information to this solution:
HEY ! I HAVE PURCHASED A VFD WITH MATCHING SPINDLE 1.5KW AND CONTROL PROGRAM UCCNC. MY INTERFACE CARD IS DB25, THE QUESTION HOW DO CONNECT TO DB25 SO THAT CAN SPEED UCCNC? SINCERELY "CNC BEGINNERS"

It seems to be getting some kind of interference or a short within the wiring or communication, try jogging the motors in the software without anything wired to the board. Then add one motor at a time to see if there is a short within your wiring or a faulty driver/motor.
If the USB breakout board continues to move the x-axis with no motors or driver wired to it, please email customerservice@buildyourcnc.com for a replacement or further troubleshooting.

Click the link to add information to this solution:
I AM USING USB BREAKOUT BOARD WITH PLANET-CNC SOFTWARE. WHEN ENABLE JOGGING KEYBOARD X AXIS STARTS TO MOVE BY ITSELF (WHETHER CONNECTED OF NOT). PRESS STOP - IT STOPS FOR A MOMENT AND THEN AGAIN. WHAT COULD THAT BE? TRIED REINSTALL SOFTWARE DID NOT HELP.

Do you have Windows 10? Did you do a major update on Windows 10? Many customers are finding that the most recent (6/3/2018) update of Windows 10 is crashing Mach3. Contact Machsupport.com to inform them of this problem.

Click the link to add information to this solution:
I have purchased Mach 3 license, motors, drivers, and break-out board from you.....gotten it all working..... but recently, a friend tried to help me load Alpha Cam toolpath code with no success, now Mach 3 won't even load. how do I get it working again?

The Mach3 USB will not work with Linux CNC. You can use our parallel breakout baord instead (if you have a computer that has a parallel port available).

Here is the link to that interface:
https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay

Click the link to add information to this solution:
Hello. I'm currently building my first CNC router, and I'm powering it with a 3 axis electronics kit that was purchased through your site. I chose to get the Mach 3 USB Breakout board, but now I'm wanting to try to use Linux CNC to work with the computer I have available. Will that work with this board?

Please email us at customerservice@buildyourcnc.com for replacments/refunds.

However dealing with Autodesk Fusion, did you choose the postprocesser ending with g-code or Mach 3? Using these postprocesser's will work with the planet-cnc program!
Our parallel BoB, with linux-cnc or Mach 3 will work with the arch definition.

Click the link to add information to this solution:
Planet-CNC's USB Controller Software doesn't support the arc definition. Can I get a refund for their hardware I purchased from you? I need something that supports gcode generated by Autodesk Fusion or supports the gcode definition http://linuxcnc.org/docs/html/gcode.html ?

You can only use the planet-cnc interfaces with the PlanetCNC software. If you like the software and want to remain with that software, the hardware interfaces will need to be purchased from the planet-cnc folks.

I would recommend using the Pokeys57CNC interface which is compatible with Mach3 and Mach4. You can also consider the Mach3 USB interface if the Pokeys57CNc interface is out of your price range.

Pokeys57CNC product page:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Mach3 USB product page:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Click the link to add information to this solution:
I have registered version of planetcnc software that I purchased with a Chinese controller I want to use 3 better drivers with a separate USB controller can you recommend a controller and how to link my existing software. Regards Lloyd from Australia