No, you should not have received two parallel breakout boards in your CNC kit. You can return the extra item using standard shipping with COD. Our apologies for the confusion and the inconvenience.

I will answer the other question as another FAQ. Please check the Customer Service page to see the answer to that question.

If you have difficulty finding the answer, here is a link:
https://www.buildyourcnc.com/FAQ/13636

Click the link to add information to this solution:
I HAVE A 2000 WK 11–3 Z LIMIT SWITCHES GOING TO C10R10 BREAKOUT BOARD . CAN ALSO USE THEM AS MY HOME POSITION WELL. NEED THE WIRING CONFIGURATION

Are you using shielded wire? If so, take the shield to ground. If there are any other wires in the cable that is not being used, ground those as well. The customer can also try moving the cables as far away as possible from the motor wires and motors.

Additional Information:


Additional Information:

Click the link to add information to this solution:
MY LIMIT SWITCHES ARE TRIGGERING AT RANDOM.

The blackFoot CNC machine kit does not include a table. The table can be made as long or shot as you need. for instance, if you are looking for a travel of 4 fet x 4 feet, then the table will need to be about 6 feet long to get the full 4 feet of travel.

The electronics are very straight forward using the connection diagram for the breakout board that you select. Use the videos for a general idea and then use the connection diagram to verify the correct connections for the interface of your choosing.

Yes,the USB interface replaces the breakout board, but remember that you will need to use the planet-cnc software with the USB interface.

Additional Information:
The electronics does accompany the cnc machine kits as long as you select the option "with electronics". There are option to purchase the machines without electronics and that would be necessary if you either have your own electronics, or you prefer the plug and play cnc computer system we call the redLeaf, or redSprout. This will also be necessary if you prefer the electronics that use the USB interface rather than the parallel interface.

Additional Information:

Click the link to add information to this solution:
WHERE ARE THE ELECTRONICS WIRING VIDEOS?

The electronics and wiring videos are located under the tutorials section (click Tutorials on the top menu. The Title is "CNC Electronics and Wiring". The actual link to these videos is: https://www.buildyourcnc.com/CNCElectronicsandWiring.aspx

Additional Information:
You will also find the electronic wiring videos for the USB controller at: https://www.buildyourcnc.com/tutorials/tutorial-Electronics-USB-Interface-Wiring

Click the link to add information to this solution:
WHERE ARE THE ELECTRONICS WIRING VIDEOS?

Portable cell phones emit about 0.6 watts of radiofrequency energy, limited primarily by the power of the battery. As with any radiofrequency transmitter, there will be some amount of absorption in the human body; the amount depends on how close you are to the antenna. The Federal Communications Commission (FCC) limits the amount of radiofrequency energy which cell phones can deposit in the body to levels at which no health effects are to be expected. See an article on Cell Phone Safety on this website for more information.

Gary H. Zeman, ScD, CHP

Click the link to add information to this solution:
HOW MUCH RADIATION GIVEN OFF BY A CELL PHONE AND THERE ANY WAY TO STOP THE FROM BEING ABSORBED INTO YOURSELF?

You can use one of the terminals on the input side of the breakout board to connect the e-stop switch.

Additional Information:

Click the link to add information to this solution:
WHICH WIRES ARE CONNECTED TO THE EMERGENCY STOP BUTTON

Are you using shielded wire? If so, take the shield to ground. If there are any other wires in the cable that is not being used, ground those as well. The customer can also try moving the cables as far away as possible from the motor wires and motors.

Additional Information:


Additional Information:

Click the link to add information to this solution:
PROBLEM WITH LIMIT SWITCHES TRIGGERING

The two main constraints on siting cellular base stations near residential areas are government exposure limits and local zoning ordinances. Various governments have limits for human exposure to radiofrequency (RF) energy that must be complied with in the siting of cellular base stations and other transmitters. In the United States, the relevant limits are those of the Federal Communications Commission (FCC). Cellular base stations use low-powered transmitters, and RF signal levels are invariably below FCC limits at any distance more than a few feet from the antennas. Thus it is entirely feasible to locate cellular base stations on rooftops of apartment buildings and to locate communications towers within residential areas and indeed these are both common practices. Local zoning ordinances are a different story. Local governments commonly restrict the location of communications towers through zoning ordinances, and they may have provisions that restrict cellular base stations in residential districts. Local attorneys or government officials should be consulted for advice about local requirements, which vary greatly among jurisdictions. Kenneth R. Foster Professor, Department of Bioengineering University of Pennsylvania

Click the link to add information to this solution:
THERE ANY STANDARD FOR A DISTANCE BETWEEN CELLULAR BASE STATION AND RESIDENTIAL AREA?

If you select the Settings Page and select or tick Auto Limit Override - this will allow you to back off the switch.

Additional Information:
limit and home switch

Click the link to add information to this solution:
IS THERE A WAY TO GET RID OF THE PARALLEL CABLE AND SOMEHOW USE USB ?

The most important factor in preventing outbreaks is annual vaccination of all occupants of the facility, and all persons in the facility who share the same air as the high-risk occupants. Groups that should be targeted include physicians, nurses, and other personnel in hospitals and outpatient settings who have contact with high-risk patients in all age groups, and providers of home care to high-risk persons (e.g., visiting nurses, volunteers).

Click the link to add information to this solution:
ARE THERE RECOMMENDATIONS FOR THE PREVENTION OF INSTITUTIONAL OUTBREAKS INFLUENZA?

You can find the wiring diagrams for the blackTooth on step 105 and 106 on the list of instructions on the blackTooth page. Step 105 pertains to the parallel breakout board and step 106 pertains to the USB interface board.

Additional Information:
wire size

Click the link to add information to this solution:
WHERE ARE THE WIRING DIAGRAMS FOR BLACKTOOTH LASER CUTTER IN INSTRUCTIONS?

Here is the wiring diagram for the MAch3 USB breakout board:
https://www.buildyourcnc.com/Documents/Electric%20Wiring%20Diagram.pdf

You will need 24 volt relays for the output on that board since that side of the board requires 24 volt power at the V+ and V-

Customer Response:
My inquiry is for the Planet CNC USB and 5v relays.
I am 99% finished with my 2 axis lathe build and this is the last item for me to conquer.
I want to control power to router, and vacuum with the BOB going through the 5V relays purchased on this site.
Thanks again.

Using the Mist, spindle or flood pins...

Buildyourcnc response:
There is an IN, GND and 5V for the digital side to engage the relay. There is an S, O and P for the power line of the device to be controlled.

The 5V and GND must be connected to the 5V and GND from the USB board. The IN is the wire from the output terminal (i.e. mist, flood, spindle).

For the power side, here are the scenarios:
- P to O connection is normally open
- P to S connection is normally closed

So, if you have the power wire that would plug into the wall, the L "black" wire from the power cord will pass through this part of the circuit (cutting the wire and one end in the P terminal and the other end in the O or S terminal). Generally, the P to O is used as this connection is normally open and when the relay is engaged, the circuit will close allowing the current to flow through that wire.

Click the link to add information to this solution:
SIGNAL AND 5V POWER WIRING DIAGRAM FOR RELAY USB BR ABOUT BOARD.

What 3d printer do you have?

Additional Information:
whiteant

Click the link to add information to this solution:
HAVE 3D PRINTER THAT WANT TO MAKE CNC ROUTER ,IS THERE ANY GUIDES SHOW ME THE WAY

If you are located near Houston, Texas area you can stop by our shop. If you are not near us, you can check in our forums, and see if you can find someone in your area that has one of our machines, and would be willing to let you come see it in action.

Click the link to add information to this solution:
I WOULD LIKE TO KNOW IF THERE IS A STORE OR SHOP WHERE CAN SEE THE PRODUCT AND BUY IT?

Try slowing your feedrate down and increasing spindle RPMs. End-mills will leave a poor finish if you go too fast. Make sure your cutting depth isn't too much. Maybe the endmill or cutter is blunt? Could it be the feed direction of the cutter? Some materials need to be fed in a certain direction.

Click the link to add information to this solution:
MOTOR GOING TWO DIRECTION WHEN JUST PUSH UP. IT WILL GO DOWN AND THEN GOES AGAIN UP WITH THE SAME BUTTON.

http://buildyourcnc.com/PrimeronHomingandLimitSwitches.aspx
There is a pin setting in Mach3 that says how to react to the inputs from the switches. Your setting is probably wrong as the trigger happens immediately.

You may want to think about shielded wire and/or a resistor on each limit switch line. If there are stray wires, connect them to ground. Additionally, the shield from the shielded cable insulation should alse connected to ground at both ends.
Try upping the Debounce interval in Mach3. You have to adjust the debounce interval. You go to config,general config, and it is in the top right corner. I set mine to 100 and it seems to work well.

Additional Information:
how to solution cnc revo 540 limit tripped error?


Additional Information:


Additional Information:


Additional Information:

Click the link to add information to this solution:
THE SWITCHES KEEP TRIPPING! AT TIMES IT IS LITERALLY AS SOON CLICK RESET ON MACH 3 THEY TRIP AGAIN.

the package sizes will be listed in your shopping cart, in the item detail. The site will also fully calculate shipping charges directly from the carrier, for each package you purchase.

Additional Information:

Click the link to add information to this solution:
AND WHAT SIZES ARE THE PACKAGES OF MACHINE.

Tinnitus . Learn to love it. No really you should see a doctor. Make sure. White noise will help you sleep when it gets loud.

Additional Information:
I learned, too late, that if a sudden loud event causes tinnitus, see an audiologist IMMEDIATELY. They can do something about it if addressed within a day or so.

Wear hearing protection...always. Loud noises trigger my tinnitus, and headphones and ear plugs (when out & about or at the movies, subway, etc) help tremendously. Mine are rated 33dB.

Click the link to add information to this solution:
WHAT CAUSES RINGING IN YOUR EAR AND HOW CAN YOU STOP IT?

The lens is 20mm wide and a 50.6mm focal length (the one included). This lens will stand up to at least 30PSI air assist.

The mirrors are 25mm wide mirrors.

Focal length is the distance from the lens to the material for the laser converge into the best focal point. If a lens is listed as 2". You measure 2" from the lens to the material, this will be the tightest point the laser can go before it starts to re-expand again losing focus.

Click the link to add information to this solution:
WHAT ARE THE BLACKTOOTH LENS SIZES AND FOCAL LENGTH SPECIFICATIONS?