[ Log In ]
[ Register ]

Question #: 14134

Question: Do you have it in stock? (NEMA 11 Stepper Motor (16.7 oz-in .185" dual shaft) 0.67 Amps)

Current Solution

Yes, we have the NEMA 11 16.7 oz-in stepper motor with dual shaft in stock.

Respond:

Other Possible Solutions to this Question

  • Is the NEMA 11 Stepper Motor (16.7 oz-in .185" dual shaft) 0.67 Amps actually a dual shaft stepper motor? The drawings only show the shaft coming out one side.

    The NEMA 11 16.7 oz-in motor is a dual shaft motor and the rear shaft extend 15mm or .59 inches.

    I've added an image to the product page:
    https://www.buildyourcnc.com/item/electronicsAndMotors-nema11-16!7ozin-NEWBIEHACK-motors-stepping_motor-16!7_ozin

    Click the link to add information to this solution:
    Is the NEMA 11 Stepper Motor (16.7 oz-in .185" dual shaft) 0.67 Amps actually a dual shaft stepper motor? The drawings only show the shaft coming out one side.

  • I HAVE ONE OF YOUR SMALLER STEPPER MOTORS RUNNING MY X AXIS BRIDGE CRANE AND IF IT IS MOVED TO FAST THE MOTOR SOUNDS LIKE SKIPPING STEPS WILL 651OZ REQUIRE A DIFFERENT POWER SUPPLY CONTROLER?

    Yes, the 651 oz/in motor requires a driver that is compatible to the motors (the motor will draw 6 amps max and the driver paired with this motor will be able to allow for a 6 amp draw). I would also recommend a 36 volt power supply for better high velocity performance.

    Click the link to add information to this solution:
    I HAVE ONE OF YOUR SMALLER STEPPER MOTORS RUNNING MY X AXIS BRIDGE CRANE AND IF IT IS MOVED TO FAST THE MOTOR SOUNDS LIKE SKIPPING STEPS WILL 651OZ REQUIRE A DIFFERENT POWER SUPPLY CONTROLER?

  • DO YOU HAVE BLACKTOE MACHINES WITH TABLES READY TO GO OR HOW LONG DOES IT TAKE MAKE ONE?

    Yes, we have the optional table for the blackToe, but we need to fabricate it, which only takes one day. We generally reserve one week for the total fabrication and packing of all parts.

    Click the link to add information to this solution:
    DO YOU HAVE BLACKTOE MACHINES WITH TABLES READY TO GO OR HOW LONG DOES IT TAKE MAKE ONE?

  • hi am over in the uk and was looking to buy one of your stepper motor bundels but our power is 240v instead of 110v do u sell other power supply units to suit our voltage thanks.

    The power supply units that come with our Electronics Combo Kits have a switchable input voltage. There is a red switch on the side that allows you to switch from 220v to 110v.

    Click the link to add information to this solution:
    hi am over in the uk and was looking to buy one of your stepper motor bundels but our power is 240v instead of 110v do u sell other power supply units to suit our voltage thanks.

  • How long does it take to ship to Israel 3 nema 11 stepper motors ?

    Unfortunately I am not able to give an estimate of shipping time. This is because there are multiple shipping options, Some of them cost more than others, but ensure the package arrives in a certain number of days. Others do not give a number of days, and many factors could change the length of shipping time, such as weather, or busy season. It would be best to choose an option you are comfortable with the price of, and then Google search the typical times it takes for that option to get to you, or call the shipping company and request that estimated time from them.

    Click the link to add information to this solution:
    How long does it take to ship to Israel 3 nema 11 stepper motors ?

  • Your 2.2kw spindle w/inverter is out of stock for 110v, do you anticipate on offering these soon?

    We may deprecate these units as we had too many issues with them.

    Click the link to add information to this solution:
    Your 2.2kw spindle w/inverter is out of stock for 110v, do you anticipate on offering these soon?

  • we just received two nema 11 stepper motors per our order--USR2-2, however they are single shaft, we need double shaft, I thought that's what we ordered. We're sending them back, let me know if you do have the double shaft version and I'll try again to order them. I notice the model number on the motor ends in "A", where the packing slip shows "B".

    We just received our new inventory of motors and that specific stepper motor ski came back with only one shaft. I’m not at the office to look at this inventory, so if that is true, they will all be single shaft. We may have other stepper motors with included rear shafts, but I will have to see on Monday.

    If I don’t have the double shaft, we will provide a refund upon receipt of the motors. My apologies for this error.

    Additional Information:
    Hi, I'm sending these motors back today. As I understand you, you might have some motors from the previous lot still in stock, and these would be double shaft but otherwise you don't have any and won't be getting any. If you do have two double shaft versions of this motor please send them; if you don't have two of them please let me know--today if possible--so I can start looking elsewhere. Thanks, Ted Armen

    Click the link to add information to this solution:
    we just received two nema 11 stepper motors per our order--USR2-2, however they are single shaft, we need double shaft, I thought that's what we ordered. We're sending them back, let me know if you do have the double shaft version and I'll try again to order them. I notice the model number on the motor ends in "A", where the packing slip shows "B".

  • DO YOU SUPPLY THE MALE PORTION OF MOTOR CONTROL CABLES WITH REDLEAF?

    Yes and properly soldered.

    Additional Information:
    20

    Click the link to add information to this solution:
    DO YOU SUPPLY THE MALE PORTION OF MOTOR CONTROL CABLES WITH REDLEAF?

  • DO NEED TO SQUARE UP THE MACHINE AND IF SO YOU HAVE INSTRUCTIONS OR VIDEO FOR THIS?

    The eyebolts are used in the squaring of the machine. I would use a standard carpenters square and first run the end mill along the edge of the square to first make it parallel with the long axis. Then run the end mill along the other edge with the short axis and adjust the eye bolts and chain according to the angle that the machine is out of square.

    Click the link to add information to this solution:
    DO NEED TO SQUARE UP THE MACHINE AND IF SO YOU HAVE INSTRUCTIONS OR VIDEO FOR THIS?

  • I HAVE NEMA 34 MOTORS BUT NEED THE ELECTRICAL COMPONENTS DO YOU A KIT WITHOUT INCLUDED?

    If you are looking for the drivers to pair with NEMA 34 stepper motors, you can find the 6.0 amp drivers here:
    https://www.buildyourcnc.com/item/electronicsAndMotors-stepper-driver-6!0a

    The other electronics to send the signals to the 6.0 amp drivers (the control board that operates with the control software) is subject to personal preference, but here they are listed:

    Our breakout board (works with Mach3 and LinuxCNC and requires a parallel port on your computer):
    https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay

    The PoKeys57CNC (works with Mach3 and Mach4):
    https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

    Generic USB breakout board (works with Mach3):
    https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

    Additional Information:
    Do I need a driver for every motor or can I use one driver for all four motors

    Additional Information:
    Each motor needs its own driver.

    Click the link to add information to this solution:
    I HAVE NEMA 34 MOTORS BUT NEED THE ELECTRICAL COMPONENTS DO YOU A KIT WITHOUT INCLUDED?

  • I HAVE NOT SEEN ANY REFERENCES TO STEPPING MOTOR ENCODER FEED-BACK FOR CLOSED LOOP CAPABILITY IN OF THE HARDWARE YOU SELL. THIS A SUPPORTED FEATURE WITH HARDWARE/SOFTWARE SELL?

    I haven't delved into using encoders with stepping motors too much. From my research, you need to have a controller that can provide the closed loop control, rather than software handling that process. I have also found from my research that using encoders on stepping motors is generally used to stop the machine in the case that the motor failed to achieve the commanded position for some reason and gives the user the chance to correct and continue with the job.

    If you want proper closed loop control, it may be best to go with servos and servo controller that provide the closed loop control within the real of those two components.

    Click the link to add information to this solution:
    I HAVE NOT SEEN ANY REFERENCES TO STEPPING MOTOR ENCODER FEED-BACK FOR CLOSED LOOP CAPABILITY IN OF THE HARDWARE YOU SELL. THIS A SUPPORTED FEATURE WITH HARDWARE/SOFTWARE SELL?

  • HOW DO I WIRE THE 4TH AXIS THAT YOU SELL. I HAVE MACH3 SOFTWARE. NO INSTRUCTIONS ON YOUR SITE

    The motor that is attached to the 4th axis is wired as follows:

    The motor should have red, green yellow and blue wires coming form the motor. The red and green are paired as one coil and the yellow and blue is paired as the other coil. You can wire the motor to a 3.0 amp driver with red to A+, green to A-, Yellow to B+ and Blue to B-

    Click the link to add information to this solution:
    HOW DO I WIRE THE 4TH AXIS THAT YOU SELL. I HAVE MACH3 SOFTWARE. NO INSTRUCTIONS ON YOUR SITE

  • DO YOU HAVE SPECIAL DEALS FOR HACKERSPACES OR NON-PROFIT ORGANIZATIONS?

    We just don't make enough on our machines to justify any discounts. We try to offer everyone the same low price.

    If I can help in another way, please let me know.

    Click the link to add information to this solution:
    DO YOU HAVE SPECIAL DEALS FOR HACKERSPACES OR NON-PROFIT ORGANIZATIONS?

  • DO YOU HAVE CAD AVAILABLE FOR THE HIWIN GUIDE BLOCKS SELL AND RAIL?

    We don't have cad models of the HIWIN blocks, but you can find the models on McMaster.com. They have can drawings and models for most of these types of parts.

    Click the link to add information to this solution:
    DO YOU HAVE CAD AVAILABLE FOR THE HIWIN GUIDE BLOCKS SELL AND RAIL?

  • DO YOU HAVE CAD AVAILABLE FOR THE HIWIN GUIDE BLOCKS SELL AND RAIL?

    We don't have cad models of the HIWIN blocks, but you can find the models on McMaster.com. They have can drawings and models for most of these types of parts.

    Click the link to add information to this solution:
    DO YOU HAVE CAD AVAILABLE FOR THE HIWIN GUIDE BLOCKS SELL AND RAIL?

  • WHY IT DANGEROUS TO HAVE YOUR MOBILE PHONE IN OPERATION DURING REFUELING AT A GAS STATION?

    I can't think of any reason that it would be dangerous. However, I checked with the Cellular Telecommunications Industry Association. The Chairman of the Association sent the following memo on 18 June 1999, to the Associations' Board of Directors and others:
    "You may have received inquiries about wireless phones causing fires or explosions at gas stations. In particular, you may have been asked about an alleged explosion at a gas station in Indonesia. We have been unable to verify any such occurrence in Indonesia or anywhere else. Moreover, in our discussions with Shell Oil they have stated they have attempted to verify these reports and also have not been able to document any such occurrence."
    Nonetheless, in an abundance of caution, some manufacturers have included language in the owner's manuals for their products that recommends wireless phone users turn off their phones while at refueling points (gas stations). In addition, we have received information that Exxon will begin issuing warning signs at all domestic gas stations advising drivers to turn off all wireless communications devices when entering Exxon gas stations.

    While wireless phone owners should always consult their owner's manual for information on the use of the phone, we are not aware of any incident that would justify these concerns."

    Gen Roessler, Editor
    HPS website

    Click the link to add information to this solution:
    WHY IT DANGEROUS TO HAVE YOUR MOBILE PHONE IN OPERATION DURING REFUELING AT A GAS STATION?

  • THE CNC MACHINE IS UNSAFE WITH EXPOSED SPROCKETS THAT CAN DAMAGE FINGERS AND HAVE CLOTHING CAUGHT IN IT.

    These machines are inherently dangerous. Before the machine moves, the machine should be clear of any person by a dimension of at the distance of a persons reach plus a few more feet. This is the policies we institute in our shop and what is recommend to all of our customers. Treat these machines as you would treat any major power tool in the shop.

    With that said, you can certainly add some protective parts, but still keep folks away even with those installed. I would use the gantry side to do all of the mounting of the protective parts. Consider using sheet metal that you can bend and make a simple installation right on the gantry side.

    Click the link to add information to this solution:
    THE CNC MACHINE IS UNSAFE WITH EXPOSED SPROCKETS THAT CAN DAMAGE FINGERS AND HAVE CLOTHING CAUGHT IN IT.

  • HOW MANY STEPS PER INCH DO I SET IN MOTOR TUNING?

    blueChick:

    X-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    blackToe:

    X-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    blackFoot:

    X-axis
    “CW8060 (6.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100 (“0”=down, “1”=up)
    Mach3 Motor Tuning: 914.29 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    greenBull:

    X-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/16 Microstep
    Dipswitches: 01100110 (“0”=down, “1”=up)
    Mach3 Motor Tuning: 914.29 steps/in

    Y-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/16 Microstep
    Dipswitches: 01100110
    Mach3 Motor Tuning: 914.29 steps/in

    Z-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/4 Microstep
    Dipswitches: 01100100
    Mach3 Motor Tuning: 1600 steps/in


    Scratch-Build / Book-Build Kit:

    X-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100 (“0”=down, “1”=up)
    Mach3 Motor Tuning: 1600 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    Additional Information:


    Additional Information:
    Scratch built/book CNC with NEMA 34 motors and CW8060 microstep driver

    Additional Information:

    Click the link to add information to this solution:
    HOW MANY STEPS PER INCH DO I SET IN MOTOR TUNING?

  • Do you have 1/8 collet matched with Dewalt DW611?

    At this time we carry router collets that are compatible with the Porter Cable 690/7500 series and the Bosch 1617/1618/1619 series of routers.

    Our current selection of collets can be seen at this page of our website: https://buildyourcnc.com/collets.aspx

    You might also consider one of our spindles, found here: https://buildyourcnc.com/SpindlesAndAccessories.aspx for which we carry a full range of collets.



    Additional Information:
    http://www.elairecorp.com/dewaltroutercollets.html MAKE SURE of model # (scroll down for DWP611)

    Click the link to add information to this solution:
    Do you have 1/8 collet matched with Dewalt DW611?

Get Help with:
This Product
Orders
Tech Support
Sales
This Product
Order Query
Tech Support
Sales
Not logged in. Log In Register
Track Order(s)
View Order(s)
I Want to Schecule a One-On-One Paid Tech Support Session
Book an Appointment Pertaining to a BuildYourCNC Product (Free)
Ask a Quesion Below (Free):
Book an Appointment Pertaining Other Equipment ($60/half hour)
Book an Immedite Appointment Pertaining Other Equipment ($120/half hour)
Ask a Quesion Below (Free):
Waiting for response... I may not answer immediately, but I was notified on my cellular phone so my response is forthcoming. If I don't respond immediately, you can always go to the [My Account] page to see all of our chats at any time.