[ Log In ]
[ Register ]
NEW: CNC Router PLANS Available for all of our Newest CNC Models!! Click here to "Design Your CNC".

Question #: 14224

Question: How do I wire two motors parallel

Current Solution

To have two stepper motors move simultaneously, connect the two stepper motor drivers to the same CP (step pulse) and CW (direction) pins for that axis.

Additional Information:
Can you send me a wiring diagram
kkitching@hughes.net

Respond:

Other Possible Solutions to this Question

  • How do I wire to nema 23 motors parallel

    Wiring two motors in parallel is pretty easy.

    Here are the steps:
    - You need to have two stepper motors and two stepper motor drivers.
    - Each stepper motor will be connected to its own stepper motor driver.
    - Both stepper motor drivers are connected to the same CP and CW pins on the interface so the same signal is delivered to both drivers.

    Click the link to respond:
    How do I wire to nema 23 motors parallel

  • I need wiring diagram to wire two nema motors parallel

    To move two stepper motors simultaneously with the same signal, simply wire the two stepper motor drivers to the same interface board signal terminals (CP and CW).

    Click the link to respond:
    I need wiring diagram to wire two nema motors parallel

  • How do I wire two stepper motors for one axis?

    Yes, you can use 2 motors in the same axis output, however you will still need a driver for that motor! Also depending on the orientation on which you mount the motor you might have to invert the direction of the motor, and that will be simple by swapping the A+,A-, to the B+,B- locations and vice versa, from the driver to the motor wiring.

    Also you can run a slave motor using another axis on the board, and setting it up in the Planet-CNC settings.

    Planet-CNC/File/Settings/Axes, here you will enter 3 in the Number of Axes location, and then change the Function of the Axis 4 to Slave 1. There you will have the 4th axis or A-axis be a slave for the x-axis.
    Slave 1 - X-Axis
    Slave 2 - Y-Axis
    Slave 3 - A-Axis
    Slave 4 - B-Axis
    Etc...

    Click the link to respond:
    How do I wire two stepper motors for one axis?

  • I have my motors wired like the wiring diagram I have two motors on Y axis how do I wire the second motor

    To move two stepper motors simultaneously with the same signal, simply wire the two stepper motor drivers to the same interface board signal terminals (CP and CW).

    Click the link to respond:
    I have my motors wired like the wiring diagram I have two motors on Y axis how do I wire the second motor

  • How do I put two motors on the same axis

    Yes, you can use 2 motors in the same axis output, however you will still need a driver for that stepper motor. Also depending on the orientation on which you mount the motor you might have to invert the direction of the motor, and that will be simple by swapping the A+,A-, to the B+,B- locations and vice versa, from the driver to the motor wiring.

    The wiring scheme would look like this:
    The step and direction output terminals on the CNC controller interface for the axis you want to have two motors would connect to both drivers of the two stepper motors on that axis.

    Additional Information:
    I have been running two motors from the same driver for 10 years on my 3m x 1.6m router. Both motors driving the gantry are wired together. I see no reason to use two drivers. The motors are high torque Nema 34. I've had no issues.

    Click the link to respond:
    How do I put two motors on the same axis

  • Can i wire my drivers and motors in parallel to your laser controll system to add a laser unit on my router?

    It is possible to add the laser control system to an existing CNC router but there are a few considerations:

    All of the signal wires from the laser controller that connect to the drivers drivers and all of the signal wires from the CNC controller that go to the drivers will need to first pass through a tri-state gate buffer chip that will allow one set of signal wires to be switched off and the other set switched on.

    We have a board that does this in development, but If you wish to accomplish this on your own, you will need:

    - 3 Quad buffer line drivers (each one can receive 4 signal wires): https://newbiehack.com/categories/newbiehack-integrated_circuits-buffer-quad-buffer-line-driver-throughhole
    - Some perf board, solder and a soldering iron, and some hookup wire.

    If this doesn't scare you, please feel free to submit additional information and let me know if you would like more information.


    Additional Information:
    You will also need a physical switch to select laser control or CNC control.

    Click the link to respond:
    Can i wire my drivers and motors in parallel to your laser controll system to add a laser unit on my router?

  • how do I connect the parallel breakout board?

    You can go here to find the diagrams and instruction on connecting the parallel breakout board:

    https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay

    Also, please make sure to watch all of the electronics tutorial videos here:
    https://www.buildyourcnc.com/CNCElectronicsandWiring.aspx

    Click the link to respond:
    how do I connect the parallel breakout board?

  • Regarding the heavy gantry electronics combo. When choosing the parallel breakout board option, how many axis/motors does the breakout board support? Thank you!
  • How can I have two stepper motors on one axis

    Yes, you can use 2 motors in the same axis output, however you will still need a driver for that motor! Also depending on the orientation on which you mount the motor you might have to invert the direction of the motor, and that will be simple by swapping the A+,A-, to the B+,B- locations and vice versa, from the driver to the motor wiring.

    Also you can run a slave motor using another axis on the board, and setting it up in the Planet-CNC settings.

    Planet-CNC/File/Settings/Axes, here you will enter 3 in the Number of Axes location, and then change the Function of the Axis 4 to Slave 1. There you will have the 4th axis or A-axis be a slave for the x-axis.
    Slave 1 - X-Axis
    Slave 2 - Y-Axis
    Slave 3 - A-Axis
    Slave 4 - B-Axis
    Etc...

    Click the link to respond:
    How can I have two stepper motors on one axis

  • How do you connect the spindle VFD to the parallel breakout board

    The parallel board contains a relay that is connected to pin #16. You can use this relay as the start/stop by connecting the relay to the FOR and it's related digital GND pin on the VFD.

    Click the link to respond:
    How do you connect the spindle VFD to the parallel breakout board

  • IF MY COMPUTER DOESN'T HAVE A PARALLEL PORT, HOW DO I RUN THE MACHINE?

    If your computer does not have a parallel port, all you will need is a low cost PCI parallel adapter card (these can be found on amazon for $15-$20). If you plan on using a laptop (not recommended) you can try to find a PCMCIA parallel adapter, but many people have frequent issues with this setup. A more expensive solution would be to purchase a USB smooth stepper board. Unfortunately, we do not supply any of these adapters and cannot attest to their reliability.

    Additional Information:
    ur gay

    Click the link to respond:
    IF MY COMPUTER DOESN'T HAVE A PARALLEL PORT, HOW DO I RUN THE MACHINE?

  • MY COMPUTER DOES NOT HAVE A PARALLEL PORT. HOW DO I INTERFACE WITH THE MACHINE?

    If your computer does not have a parallel port, all you will need is a low cost PCI parallel adapter card (these can be found on amazon for $15-$20). If you plan on using a laptop (not recommended) you can try to find a PCMCIA parallel adapter, but many people have frequent issues with this setup. A more expensive solution would be to purchase a USB smooth stepper board. Unfortunately, we do not supply any of these adapters and cannot attest to their reliability.

    Additional Information:
    ur gay

    Click the link to respond:
    MY COMPUTER DOES NOT HAVE A PARALLEL PORT. HOW DO I INTERFACE WITH THE MACHINE?

  • how do I determine the steps per inch for the motors?

    blueChick:

    X-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    blackToe:

    X-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    blackFoot:

    X-axis
    “CW8060 (6.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100 (“0”=down, “1”=up)
    Mach3 Motor Tuning: 914.29 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    greenBull:

    X-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/16 Microstep
    Dipswitches: 01100110 (“0”=down, “1”=up)
    Mach3 Motor Tuning: 914.29 steps/in

    Y-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/16 Microstep
    Dipswitches: 01100110
    Mach3 Motor Tuning: 914.29 steps/in

    Z-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/4 Microstep
    Dipswitches: 01100100
    Mach3 Motor Tuning: 1600 steps/in


    Scratch-Build / Book-Build Kit:

    X-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100 (“0”=down, “1”=up)
    Mach3 Motor Tuning: 1600 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    Additional Information:


    Additional Information:
    Scratch built/book CNC with NEMA 34 motors and CW8060 microstep driver

    Additional Information:

    Click the link to respond:
    how do I determine the steps per inch for the motors?

  • MY COMPUTER DOES NOT HAVE A PARALLEL PORT. HOW DO I INTERFACE WITH THE BREAKOUT BOARD?

    If your computer does not have a parallel port, all you will need is a low cost PCI parallel adapter card (these can be found on amazon for $15-$20). If you plan on using a laptop (not recommended) you can try to find a PCMCIA parallel adapter, but many people have frequent issues with this setup. A more expensive solution would be to purchase a USB smooth stepper board. Unfortunately, we do not supply any of these adapters and cannot attest to their reliability.

    Additional Information:
    ur gay

    Click the link to respond:
    MY COMPUTER DOES NOT HAVE A PARALLEL PORT. HOW DO I INTERFACE WITH THE BREAKOUT BOARD?

  • DO I HAVE TO A PARALLEL PORT?

    If your computer does not have a parallel port, all you will need is a low cost PCI parallel adapter card (these can be found on amazon for $15-$20). If you plan on using a laptop (not recommended) you can try to find a PCMCIA parallel adapter, but many people have frequent issues with this setup. A more expensive solution would be to purchase a USB smooth stepper board. Unfortunately, we do not supply any of these adapters and cannot attest to their reliability.

    Additional Information:
    ur gay

    Click the link to respond:
    DO I HAVE TO A PARALLEL PORT?

  • how to connect parallel port breakout board for medium kit

    The very best way to explain how to connect the parallel breakout board is to follow these tutorials on this site: https://buildyourcnc.com/CNCElectronicsandWiring.aspx#prettyPhoto

    Click the link to respond:
    how to connect parallel port breakout board for medium kit

  • DO I NEED A PARALLEL PORT?

    If your computer does not have a parallel port, all you will need is a low cost PCI parallel adapter card (these can be found on amazon for $15-$20). If you plan on using a laptop (not recommended) you can try to find a PCMCIA parallel adapter, but many people have frequent issues with this setup. A more expensive solution would be to purchase a USB smooth stepper board. Unfortunately, we do not supply any of these adapters and cannot attest to their reliability.

    Additional Information:
    ur gay

    Click the link to respond:
    DO I NEED A PARALLEL PORT?

  • If motors are wired for Bipolar series which leads do you swap for rotation?

    For our motors, drivers and power supplies, we recommend bipolar parallel (relating to motors with more than 4 wires). The current draw and voltage combination under bipolar parallel results in better performance.

    To reverse the motor spin direction for both bipolar series or bipolar parallel, switching the "A" wires with the "B" wires will do the trick.

    Click the link to respond:
    If motors are wired for Bipolar series which leads do you swap for rotation?

  • IF I DON'T HAVE A PARALLEL PORT, WHAT DO DO?

    If your computer does not have a parallel port, all you will need is a low cost PCI parallel adapter card (these can be found on amazon for $15-$20). If you plan on using a laptop (not recommended) you can try to find a PCMCIA parallel adapter, but many people have frequent issues with this setup. A more expensive solution would be to purchase a USB smooth stepper board. Unfortunately, we do not supply any of these adapters and cannot attest to their reliability.

    Additional Information:
    ur gay

    Click the link to respond:
    IF I DON'T HAVE A PARALLEL PORT, WHAT DO DO?