Can you send me a link to the digitizer you are using?

Click the link to add information to this solution:
Hi my names is Minh Truong I would like to said thank you very much for your video I got the system mach3 working fine but one thing I can NOT set and config the digitizer on the board IN4 I am not sure how to setup because in the Mach3 pin 14 for digitizer Please shoe me hoe to set it up for the digitizer.

Yes, the 651 oz/in motor requires a driver that is compatible to the motors (the motor will draw 6 amps max and the driver paired with this motor will be able to allow for a 6 amp draw). I would also recommend a 36 volt power supply for better high velocity performance.

Click the link to add information to this solution:
I HAVE ONE OF YOUR SMALLER STEPPER MOTORS RUNNING MY X AXIS BRIDGE CRANE AND IF IT IS MOVED TO FAST THE MOTOR SOUNDS LIKE SKIPPING STEPS WILL 651OZ REQUIRE A DIFFERENT POWER SUPPLY CONTROLER?

Yes, the 651 oz/in motor requires a driver that is compatible to the motors (the motor will draw 6 amps max and the driver paired with this motor will be able to allow for a 6 amp draw). I would also recommend a 36 volt power supply for better high velocity performance.

Click the link to add information to this solution:
I have one of your smaller stepper motors running my X AXIS bridge crane and if it is moved to fast the stepper motor sounds like it is skipping steps will the 651oz stepper motor require a different power supply and controler?

The leadscrew length for the greenBull long Z-axis is 47 inches.

Additional Information:

Click the link to add information to this solution:
BUILDING ONE OF YOUR GREENBULL 6X LONG AND 2.2 KILOWATT SPINDLE DOES NOT FIT. SEEMS LEAD SCREW YOU SENT WITH KIT IS SHORT 42" LOOKS LIKE IT NEEDS TO BE 5 OR 6 INCH LONGER. THIS CORRECT? WHAT THE NEEDED LENGTH FOR UNIT?

The firmware update for the USB board is done by PlanetCNC. with your board hooked up to the computer via USB cable, log into PlanetCNC. Then, from the Machine tab on the toolbar choose firmware from the drop down and click on update.

Click the link to add information to this solution:
Is there a firmware update in the last two years for your USB board? If so how do we get it and install? If not do you expect any updates? If updates are released how do we find out?

If you would like to come to the office, please call the office at 281-815-7701 to request a visit at your specified time within our business hours so we can make sure that the right person will be there to assist you.

Click the link to add information to this solution:
I am considering the purchase of a Black foot or Green Bull CNC router and would like to come and visit your facility to see them in person and to discuss my requirements. Please can you tell me your address. I am based in NW Houston. Many thanks.

In the tracking for that package, it says it was "Delivered, Garage or Other Location at Address". The package was probably too large to insert it in the mail box. If it was delivered on your porch or garage as stated in the tracking, then a person may have walked away with it. Call your local USPS office and inform then that your package was not where it stated on the tracking.

Click the link to add information to this solution:
I have not received my order even though USPS says they delivered it to my home. Its nowhere to be found. The tracing number is 9405511699000140422765, please help me.

The USB interface only works with momentary switches unfortunately. If you have extensive knowledge of digital electronics, you can apply a receiver that uses a microcontroller and a transmitter with another microcontroller that produces the pulsing signal with the controls that you need.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
I would like to make a handheld remote for the USB CNC Board using a joystick instead of momentary switches. Could you suggest one that will work with your board.

The relay is only used for devices like routers, spindles, coolant, mist, etc. The relay works like an automatic switch and will allow current to pass when the relay is engaged.

Click the link to add information to this solution:
The relay doesn't have a A+ B - it has signal in god. 5v. / 0 S P. This has to go to my USB motion card wiring shows v+ goes to top of coil no number and comes out the bottom to #2 the relay I got from you is not that simple

First, see Jack's build: https://www.buildyourcnc.com/JackRehak.aspx

The difference between mounting the electronics in the gantry is that the connection from the computer (signal level) is long. The alternative, where the electronics is near the computer, the motor cables are long (to reach from the drivers to the motors).

Mounting the breakout board, drivers and power supply within the gantry will cause you to have a long signal connection from the computer to the breakout board. That is fine as long as the cable is long enough, possibly shielded, and can carry the signal at long cable lengths. Make sure to have the cable well away from the motor cables as these will cause quite a bit of interference.

Click the link to add information to this solution:
Provided they will fit and I install a ventilation/cooling fan, is there any reason why I should NOT mount the electronics (breakout board, stepper drivers and power supply) inside the gantry box in my BlackToe 2x4?

Your steps per inch will vary. I suggest watching my calibration video.

Click the link to add information to this solution:
I AM CURRENTLY HAVING SOME PROBLEM SQUARING THE GANTRY AND MY STEPS PER INCH ARE NOT 1422.22 ACCORDING TO YOUR CALCULATIONS IN AUTO SET UP THEY COME OUT LIKE 1416.#### THIS A BIG DEAL?

What controller are you using to control the cnc machine (Mach3 usb, parallel breakout board, etc.)?

The spindle VFD has an input for 0-10 volts to control the speed and can be used with the MAch3 USB or the Pokeys57CNC board. There are also other terminals in the VFD to control the forwared/reverse and start and stop. Mach3 has parameters to control these output and you need to specify which pins are used for these.

You can also use the TX/RX RS-485 connection on the VFD to have total control using an FTDI USB to serial connector board to connect the computer directly to the VFD.

How to connect the USB to Serial adapter to the VFD:
https://www.buildyourcnc.com/FAQ/13790

FTDI USB to Serial:
https://www.buildyourcnc.com/item/Interfaces-newbiehack-Interfaces-TTL232R-USB-UART-Serial

Pokeys57CNC board:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Mach3 USB board:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Parallel Breakout board:
https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay



Additional Information:
I do apologize for leaving out the parts list.
Leadshine MX4660 4-Axis Digital Stepper Motor Driver
Ethernet SmoothStepper
YL600-2S-2K20 VFD
4 Relay control board
Has anyone had any success getting Mach3 to control the spindle speed and direction?

Click the link to add information to this solution:
I have the 2.2KW VFD. I would like to have it controlled through software. What are the Mode parameters that need to be changed that will allow FWD/ REV, START/STOP and RPM control?

Currently our USB breakout board is only compatible with Planet-CNC software as it has to be registered with Planet-CNC.

Click the link to add information to this solution:
Hi, I have watched your vids on YouTube and I am interested in purchasing one of your USB Break-Out Boards. I currently own and use FlashCut CNC software, which is USB based, on all of my machines. I'm wondering if you could tell if the Flashcut software will talk with the USB Break-Out Board? Thank You

I haven't delved into using encoders with stepping motors too much. From my research, you need to have a controller that can provide the closed loop control, rather than software handling that process. I have also found from my research that using encoders on stepping motors is generally used to stop the machine in the case that the motor failed to achieve the commanded position for some reason and gives the user the chance to correct and continue with the job.

If you want proper closed loop control, it may be best to go with servos and servo controller that provide the closed loop control within the real of those two components.

Click the link to add information to this solution:
I HAVE NOT SEEN ANY REFERENCES TO STEPPING MOTOR ENCODER FEED-BACK FOR CLOSED LOOP CAPABILITY IN OF THE HARDWARE YOU SELL. THIS A SUPPORTED FEATURE WITH HARDWARE/SOFTWARE SELL?

I just sent you the commercial invoice via email. Thanks.

Click the link to add information to this solution:
Could you please e-mail us the invoice for the order, shipment is currently at the customs and your invoice is needed so it can be cleared. As I can't seem to find any order number or other reference in your system, the only reference I have is the tracking number LZ676176940US and the order date is 12/26/2017. Thanks!

Can you provide the model number of your VFD?

Yes, I have the "YL600 - 2S - 2K20"

It just came with a small booklet that is all in Chinese...

Click the link to add information to this solution:
I WIRED MY VFD (2.2KW VERSION) AND TRIED TEST RUNNING THE SPINDLE. CONFIGURED TO YOUR SPECS ON THIS WEBSITE, ONLY ISSUE IS WE GOT AN ERROR CODE. ERR 02, DO YOU KNOW WHAT IS? OR HAVE A LIST OF CODES? THANK

Is this CNC related. If so, what controller are you using?

Additional Information:
I'm using the Mach 3/USB CNC interface board, with the Mach 3 software.

Additional Information:
Does the LED on the controller light up, or blink?

Additional Information:
I believe I've corrected the issue. I found that their are 2 spring like tabs on the female USB port. And take a sharp point like on a compass and gentle raise those tabs a bit. This tighten up the connection, and I never received an error from losing connection.

Click the link to add information to this solution:
It appears I have a connection issue with the USB port on my computer with the USB cord. I purchased a new cord but has the same issue. Is there anything I can do to correct this issue?

Do you have any intention to upgrade to Mach4? If you will be staying with Mach3 for a while, then the Mach3 USB interface is fine. If you intend to change to Mach4, then I would go with the Pokeys57CNC interface.

Click the link to add information to this solution:
Hi Patrick right now I have a parallel port cnc machine that I built in 2013. I want to update my system to use a usb. Do you recommend changing my interface board to a Mach3 USB interface board or purchasing the UC 100 parallel port to USB adapter?

Yes, our porter cable collets and nuts will fit the porter cable 7518.

Additional Information:

Click the link to add information to this solution:
HAVE PORTER CABLE 7518 ROUTER ON MY CNC AND WOULD LIKE TO KNOW IF YOUR ER20 COLLET NUT, FOR THE CABLE, WILL FIT ROUTER.